Intermatic ET2145CP Elektronisk Timer Brugsanvisning

1. Introduktion

This manual provides comprehensive instructions for the installation, operation, and maintenance of your Intermatic ET2145CP Electronic Timer. This device is designed for 24-hour and 365-day operation, capable of handling up to 30 Amps at 120 to 277Vac. Please read this manual thoroughly before installation and use to ensure safe and proper functionality.

2. Vigtige sikkerhedsoplysninger

ADVARSEL: Risiko for brand eller elektrisk stød

• Afbryd strømmen ved afbryderen/afbryderne eller afbryd kontakten/afbryderne før installation eller servicering.
• Der kan være behov for mere end én afbryder eller afbryderkontakt for at afbryde udstyret før servicering.
• Installation og/eller ledningsføring skal være i overensstemmelse med nationale og lokale elektriske krav.
• Bruge KOBBER conductors ONLY.
• Do IKKE remove the insulator covering the terminals.

3. Produktet er slutview

The Intermatic ET2145CP Electronic Timer features a clear digital display and intuitive controls for programming. Key components include:

• Digital skærm: Shows current time, date, and programming information.
• MODE knap: Used to cycle through different programming modes (e.g., time setting, event programming).
• ENTER/NEXT Button: Confirms selections and advances to the next setting.
• ON/OFF knapper: Used for manual override or to set ON/OFF times for programmed events.
• CLEAR MEM Button: Clears all programmed events or settings.
• CLEAR ENTRY Button: Sletter den aktuelle indtastning under programmering.
• Pil op/ned: Adjust values (time, date, event numbers).
• Klemmeblok: For electrical wiring connections.

4. Installationsvejledning

Follow these steps for proper installation of the Intermatic ET2145CP Electronic Timer:

1. Strømafbrydelse: Before beginning any work, ensure all power to the circuit is disconnected at the main circuit breaker or disconnect switch. Verify with a voltage tester.
2. Access Wiring Terminals: To access the wiring terminals, lift the plastic insulator covering the terminals. You may need to remove a screw and swing the insulator aside.
3. Ledningsforbindelser: Connect the electrical wiring to the appropriate terminals. Ensure all connections are secure and comply with local and national electrical codes. Use only copper conductors.
4. Secure Insulator: Once wiring is complete, replace the plastic insulator covering the terminals and secure it with the screw (if applicable).
5. Gendan strøm: After ensuring all connections are correct and secure, restore power to the circuit.

5. Betjeningsvejledning

5.1. Initial Setup: Setting Time and Date

1. Tryk på MODE button until the time/date setting option appears on the display.
2. Brug Pil op/ned to adjust the current hour. Press ENTER/NÆSTE for at bekræfte.
3. Repeat for minutes, AM/PM (if applicable), year, month, and day.
4. Trykke MODE for at forlade indstillingsmenuen.

5.2. Programmering af TIL/FRA-hændelser

The timer supports multiple ON/OFF events. Refer to the display for available program slots.

1. Tryk på MODE button until 'PROGRAM' or 'EVENT' mode is displayed.
2. Brug Pil op/ned to select an event number (e.g., 1 ON, 1 OFF). Press ENTER/NÆSTE.
3. Indstil den ønskede ON-tid ved hjælp af Pil op/ned og ENTER/NÆSTE.
4. Set the desired OFF time using the Pil op/ned og ENTER/NÆSTE.
5. Select the days of the week for this event to be active (e.g., Mon-Fri, Daily, Weekends). Press ENTER/NÆSTE.
6. Repeat for additional events as needed.
7. Trykke MODE for at afslutte programmeringen.

5.3. Manuel tilsidesættelse

To temporarily override the programmed schedule:

• Tryk på en af ON/OFF buttons to manually switch the output ON or OFF.
• The timer will typically revert to its programmed schedule at the next scheduled event.

5.4. Clearing Memory

To clear all programmed events or reset the timer:

• Tryk og hold på RYD HUKOMMELSE button for a few seconds until the display confirms memory clear.
• Alternativt kan du bruge TYDELIG INDGANG button to clear individual entries during programming.

6. Vedligeholdelse

The Intermatic ET2145CP Electronic Timer requires minimal maintenance. Ensure the unit is kept clean and free from dust and debris. Do not attempt to open the casing or repair the internal components, as there are no user-serviceable parts inside. For cleaning, use a soft, dry cloth. Avoid abrasive cleaners or solvents.

7. Fejlfinding

If you encounter issues with your timer, consider the following common troubleshooting steps:

• Intet display/Ingen strøm: Check the circuit breaker or fuse supplying power to the timer. Ensure all wiring connections are secure.
• Timer Not Switching: Verify that the programmed events are correctly set and enabled. Check if the manual override is active.
• Forkert tidspunkt/dato: Re-enter the correct time and date as per Section 5.1.
• Uregelmæssig adfærd: A power surge or interruption might cause erratic behavior. Try resetting the timer by pressing the RYD HUKOMMELSE button (this will erase all programs, requiring re-programming).

If problems persist after attempting these steps, contact Intermatic customer support for assistance.

8. Tekniske specifikationer

9. Garanti og kundesupport

For information regarding the product warranty, please refer to the warranty card included with your purchase or visit the official Intermatic website. For technical assistance, troubleshooting, or to inquire about replacement parts, please contact Intermatic customer support directly. Contact details can typically be found on the manufacturer's webwebsted eller produktemballage.