Emtek EMP1101US19

Emtek Empowered Motorized Touchscreen Tastatur Smart Deadbolt Brugermanual

Model: EMP1101US19 | Brand: Emtek

1. Introduktion og overview

The Emtek Empowered Motorized Touchscreen Keypad Smart Deadbolt combines Emtek's renowned long-lasting quality with advanced smart home technology. Designed for security and convenience, this deadbolt offers keyless entry, remote access, and intelligent features to enhance your home's safety.

This manual will guide you through the installation, setup, and daily operation of your new smart deadbolt, ensuring you can fully utilize its capabilities.

Emtek Empowered Motorized Touchscreen Keypad Smart Deadbolt, front view

Figur 1.1: Forside view of the Emtek Empowered Motorized Touchscreen Keypad Smart Deadbolt.

2. Nøglefunktioner

Emtek Empowered Smart Deadbolt keypad and interior unit

Figure 2.1: Emtek Empowered Smart Deadbolt exterior keypad and interior unit.

August app interface, August Connect Wi-Fi Bridge, and DoorSense sensor

Figur 2.2: Overview of August connectivity features including the mobile app, Wi-Fi bridge, and DoorSense.

3. Pakkens indhold

Kontroller venligst, at alle komponenter er til stede, før installationen påbegyndes:

Diagram showing included components: Pre-Installed Module, Connect Wi-Fi Bridge, DoorSense, and compatible smart home platforms.

Figure 3.1: Visual representation of included components and smart home compatibility.

4. Opsætning og installation

The Emtek Empowered Smart Deadbolt is designed for simple installation, typically requiring only a screwdriver. It replaces most existing deadbolts and is compatible with standard doors 1-3/4” to 2-1/4” thick with a standard 2-1/8” face bore door prep.

4.1. Kontrol før installation

4.2. Installationstrin

For detailed, step-by-step 3D instructions, it is highly recommended to download and use the BILT app. The app provides visual guidance for each stage af installationsprocessen.

Generelle trin omfatter:

  1. Fjern din eksisterende dødbolt.
  2. Install the new deadbolt latch into the door edge.
  3. Monter det udvendige tastatur.
  4. Installer den indvendige monteringsplade.
  5. Connect the cable from the exterior assembly to the interior escutcheon.
  6. Secure the interior escutcheon.
  7. Install the batteries (4 AA batteries included).
  8. Perform the door handing process as instructed by the lock or BILT app.
  9. Install the August Connect Wi-Fi Bridge and DoorSense according to their respective instructions to enable smart features.
Diagram showing Hassle-Free Set-Up and Customizable Features of the Emtek Smart Deadbolt

Figur 4.1: Overview of hassle-free setup and customizable features.

5. Betjeningsvejledning

5.1. Tastaturbetjening

5.2. August App Control

The August mobile app provides comprehensive control and monitoring capabilities:

Diagram illustrating Home Mode and Away Mode for auto-unlock functionality

Figure 5.1: Home Mode and Away Mode for automatic unlocking and locking.

5.3. Stemmekontrol

Integrate your Emtek smart deadbolt with your preferred voice assistant for hands-free control:

6. Vedligeholdelse

6.1. Udskiftning af batteri

The deadbolt requires 4 AA alkaline batteries. When battery levels are low, the lock will provide an alert. To replace batteries:

  1. Remove the battery cover on the interior escutcheon.
  2. Fjern de gamle batterier.
  3. Isæt nye AA alkaline-batterier, og sørg for at polariteten vender korrekt.
  4. Sæt batteridækslet på igen.

Vigtig: In case of complete battery depletion, a 9V battery port is available on the exterior keypad for temporary power to unlock the deadbolt. Simply hold a 9V battery to the contacts on the bottom of the keypad while entering your code.

6.2. Rensning

Clean the exterior keypad and interior unit with a soft, damp klud. Undgå at bruge slibende rengøringsmidler eller opløsningsmidler, da disse kan beskadige overfladen og de elektroniske komponenter.

7. Fejlfinding

If you encounter issues with your Emtek Empowered Smart Deadbolt, refer to the following common problems and solutions:

ProblemMulig årsagLøsning
Låsen reagerer ikke på tastaturinput.Dead batteries; Keypad not waking up.Replace AA batteries. Ensure you are touching the keypad to activate it. Use 9V battery backup if completely dead.
Deadbolt kan ikke trækkes helt ud/ind.Door misalignment; Low battery; Obstruction in door frame.Check door alignment and strike plate. Replace batteries. Clear any obstructions. Re-run door handing process.
Cannot connect to August app or Wi-Fi.August Connect not properly set up; Wi-Fi signal weak; App issues.Ensure August Connect is plugged in and within range of the lock and Wi-Fi router. Check Wi-Fi signal strength. Restart August Connect and your mobile device. Consult August app help or BILT app.
Auto-unlock not working consistently.Phone location services disabled; App not running in background; Geofencing issues.Ensure location services are enabled for the August app. Keep the app running in the background. Calibrate your home's geofence in the August app settings.
Lock is unresponsive after installation.Incorrect wiring/connection; Missing battery contact; Manufacturing defect.Double-check all cable connections. Verify battery contacts are correctly seated. If issues persist, contact Emtek customer support.

For further assistance, refer to the BILT app or contact Emtek customer support.

8. Specifikationer

FeatureDetalje
MærkeEmtek
ModelnavnEmpowered Motorized Touchscreen Keypad Smart Deadbolt
ModelnummerEMP1101US19
LåsetypeTastatur
Særlige funktionerTouchscreen, Wi-Fi, Motorized, Backlit Keypad
MaterialeMessing
FarveFlat Black Coated (US19)
Varedimensioner (L x B x H)6 x 3 x 3 tommer
Varens vægt4.86 pund
Dørtykkelseskompatibilitet1-3/4” to 2-1/4”
Strømkilde4 AA batterier (medfølger)
Backup Power9V batteriport
ForbindelsesprotokolWi-Fi (via August Connect)
Controller typeAmazon Alexa, Google Assistant, Siri

9. Garanti og support

Emtek products are known for their quality and durability. For specific warranty information regarding your Empowered Motorized Touchscreen Keypad Smart Deadbolt, please refer to the warranty card included in your product packaging or visit the official Emtek webwebsted.

For technical support, troubleshooting assistance, or to inquire about replacement parts, please contact Emtek customer service. You can also find helpful resources and 3D installation guides on the BILT app.