PHOENIX CONTACT UTME 6 Testafbrydelsesklemme Brugermanual

Produkt overview

The PHOENIX CONTACT UTME 6 is a high-quality test disconnect terminal block designed for reliable electrical connections in industrial applications. Featuring 2 connections, it is rated for 30 Amps and 500 Volts, accommodating wires up to 6 MM². Its screw connection method ensures secure and durable wiring. This terminal block is ideal for circuits requiring easy testing and disconnection without interrupting the main circuit flow.

Figure 1: PHOENIX CONTACT UTME 6 Test Disconnect Terminal Block, showing its compact design and screw terminals.

Sikkerhedsoplysninger

Always disconnect power before installing, servicing, or removing the terminal block.
Installation should only be performed by qualified personnel in accordance with local and national electrical codes.
Ensure proper wire gauge and insulation are used for the specified current and voltage vurderinger.
Do not exceed the maximum current (30A) or voltage (500V) ratings.
Verify all connections are secure to prevent loose contacts and potential hazards.
Protect the terminal block from moisture, dust, and extreme temperatures.

Opsætning og installation

Follow these steps for proper installation of the UTME 6 terminal block:

Udpakning: Carefully remove the terminal block from its packaging. Inspect for any visible damage.
Montering: The UTME 6 is designed for DIN rail mounting. Snap the terminal block onto a standard DIN rail (e.g., NS 35/7.5 or NS 35/15) by pressing it down firmly until it clicks into place.
Forberedelse af ledning: Strip approximately 9-10 mm of insulation from the end of the wire. For stranded wires, it is recommended to use ferrules for optimal connection integrity.
Ledningsforbindelser:
- Using a suitable screwdriver, open the screw clamp på klemrækken.
- Insert the prepared wire fully into the clamping enhed.
- Tighten the screw firmly to secure the wire. Ensure no bare wire strands are exposed outside the clamping enhed.
- Repeat for all necessary connections.
Test: After all connections are made, perform continuity and insulation resistance tests as required by local regulations before applying power.

Betjeningsvejledning

The UTME 6 features a test disconnect function, allowing for easy isolation of circuits for testing or maintenance without disturbing the main wiring.

Normal drift: In its standard configuration, the terminal block provides a continuous electrical path.
Disconnecting for Test: To disconnect the circuit, simply open the disconnect knife or lever (if applicable to the specific variant, for UTME 6, it's typically a screw-operated disconnect). This isolates the circuit section connected to the terminal block.
Forbinder igen: To restore the connection, close the disconnect knife or lever. Ensure it is fully engaged for proper electrical contact.

Note: Always ensure power is off before performing any disconnect or reconnect operations if there is a risk of arc flash or other electrical hazards.

Opretholdelse

Regular maintenance ensures the longevity and reliable performance of your UTME 6 terminal block.

Rensning: Periodically clean the terminal block using a dry, lint-free cloth. Avoid using solvents or abrasive cleaners that could damage the plastic housing.
Inspektion: Visually inspect the terminal block for any signs of damage, discoloration, or loose connections. Check for corrosion on metal parts.
Efterspændingsskruer: Over time, screw connections can loosen due to vibration or thermal cycling. Periodically retighten the screw connections to the recommended torque (refer to PHOENIX CONTACT technical documentation for specific torque values, generally 0.5-0.8 Nm for M3 screws).

Fejlfinding

If you encounter issues with your UTME 6 terminal block, consider the following common problems and solutions:

Problem	Mulig årsag	Løsning
No continuity through the block	Disconnect knife/lever is open. Løs ledningsforbindelse. Damaged terminal block.	Ensure disconnect knife/lever is fully closed. Check and retighten wire screws. Undersøg for skader; udskift om nødvendigt.
Overheating/Discoloration	Overstrømstilstand. Løse forbindelser. Incorrect wire gauge.	Verify circuit current does not exceed 30A. Retighten all wire connections. Ensure wire gauge is appropriate for the load (e.g., 6 MM² or 8 AWG).
Difficulty inserting wire	Skrue clamp ikke helt åben. Wire end not properly prepared (e.g., frayed strands).	Loosen screw further. Re-strip and prepare wire end, consider using a ferrule.

Specifikationer

Modelnummer	UTME 6
Mærke	PHOENIX KONTAKT
Nuværende vurdering	30 Amps
Voltage Bedømmelse	500 volt
Trådtværsnit	6 MM² (approx. 8 AWG)
Antal forbindelser	2
Connector Type	Skrue
Antal polakker	2
Overholdelse	RoHS
Pakkedimensioner	2 x 2 x 2 tommer
Varens vægt	1.47 pund

Garantioplysninger

PHOENIX CONTACT products are manufactured to the highest quality standards. This product is covered by the standard manufacturer's warranty against defects in materials and workmanship. For specific warranty terms and conditions, please refer to the official PHOENIX CONTACT webwebstedet eller kontakt deres kundesupport direkte. Behold din købskvittering som købsbevis.

Kundesupport

For technical assistance, product inquiries, or support, please contact PHOENIX CONTACT customer service:

Webwebsted: Visit the official PHOENIX CONTACT website for comprehensive product documentation, FAQs, and contact information. www.phoenixcontact.com
Teknisk support: Der henvises til website for regional technical support contact details (phone numbers, email addresses).

	Phoenix Contact PTTB 2.5-PE beskyttelsesleder dobbeltniveau-klemrække installationsvejledning Installationsvejledning og tekniske specifikationer for Phoenix Contact PTTB 2.5-PE beskyttelsesleder dobbeltetagesklemme med push-in-tilslutning, egnet til brug i eksplosionsfarlige områder.
	Phoenix Contact SUNCLIX fotovoltaiske stik - Produktkatalog Udforsk Phoenix Contact SUNCLIX-serien af fotovoltaiske stik, der er designet til pålidelige og effektive solenergisystemer. Dette katalog beskriver apparatstik, DC-stik, Y-fordelere, kabler og printkortforbindelsesløsninger, inklusive tekniske specifikationer, bestillingsoplysninger og applikationsvejledning.
	PTCB E1 24DC/0.63A SI-R: Beskyttelse af elektroniske enheder Phoenix Contact PTCB E1 24DC/0.63A SI-R er en elektronisk apparatbeskytter med én kanal til 12-24 V DC-belastninger. Har en fast nominel strøm på 0.63 A, fjernsignalering, fjernnulstilling og aktiv strømbegrænsning. Designet til DIN-skinnemontering og kompatibel med CLIPLINE-klemmer.
	Guia de Configuração do Node-RED no PLCnext \| Phoenix Contact Tilslut en konfiguration og integrar af Node-RED med PLCnext-kontrollere fra Phoenix Contact til industriel automatisering, IoT og edge computing. Guia técnico detalhado.
	Phoenix Contact EMM 3-24DC/500AC-16-IFS Motorstyring Tekniske specifikationer og funktioner for den elektroniske motorstyringsenhed Phoenix Contact EMM 3-24DC/500AC-16-IFS, inklusive elektriske egenskaber, tilslutningsdata, dimensioner og godkendelser.
	Teknisk vejledning: PLCnext og Compactlogix-kommunikation via Node-RED Lær, hvordan du integrerer PHOENIX CONTACT PLCnext- og Allen Bradley Compactlogix-controllere ved hjælp af Node-RED til industriel automation. Denne vejledning dækker konfiguration, læsning og skrivning af variabler.