1. Introduktion
Thank you for choosing the Ferm CDM1135 Cordless Rechargeable Screwdriver Kit. This manual provides essential information for the safe and efficient use of your new tool. Please read these instructions carefully before operating the screwdriver and retain them for future reference. This tool is designed for light-duty screwing tasks and is not intended for heavy professional use.
2. Sikkerhedsinstruktioner
Overhold altid grundlæggende sikkerhedsforanstaltninger for at reducere risikoen for brand, elektrisk stød og personskade.
- Sikkerhed på arbejdsområdet: Hold dit arbejdsområde rent og godt oplyst. Rodede eller mørke områder indbyder til ulykker. Brug ikke elværktøj i eksplosive atmosfærer, f.eks. i nærheden af brandfarlige væsker, gasser eller støv.
- Elektrisk sikkerhed: Udsæt ikke elværktøj for regn eller våde forhold. Vand, der trænger ind i et elværktøj, øger risikoen for elektrisk stød.
- Personlig sikkerhed: Vær opmærksom, hold øje med, hvad du laver, og brug din sunde fornuft, når du betjener et elværktøj. Brug ikke elværktøj, mens du er træt eller påvirket af stoffer, alkohol eller medicin.
- Brug og pleje af værktøj: Tving ikke elværktøjet. Brug det korrekte elværktøj til dit formål. Det vil udføre arbejdet bedre og mere sikkert med den hastighed, det er designet til. Frakobl batteriet fra elværktøjet, før du foretager justeringer, skifter tilbehør eller opbevarer elværktøj.
- Brug og pleje af batteripakken: Genoplad kun med den oplader, der er specificeret af producenten. En oplader, der er egnet til én type batteripakke, kan skabe en brandrisiko, når den bruges sammen med en anden batteripakke.
3. Pakkens indhold
Verify that all items listed below are present and in good condition upon unpacking.
- Ferm CDM1135 Cordless Rechargeable Screwdriver
- 4V 1.5Ah Li-ion Battery (integrated)
- USB opladningskabel
- 28-piece Screw Tip Set (26 x 25mm, 2 x 50mm)
- 2 Screwing Adapters (45-degree angle adapter, edge strip adapter)
- Instruktionsmanual
4. Produktet er slutview
The Ferm CDM1135 is a compact and ergonomic cordless screwdriver designed for convenience and versatility in various household and DIY tasks. It features a magnetic chuck for easy bit changes, a spindle lock for manual tightening, and a double LED worklight for improved visibility.
Figure 1: Ferm CDM1135 Cordless Screwdriver illustrating the integrated LED worklight.
Nøglefunktioner omfatter:
- Integrated 4V 1.5Ah Li-ion battery
- No-load speed of 0-200 RPM
- Maximum torque of 4 Nm
- LED battery charge indication
- Left/right rotation function
- Kompakt og ergonomisk design
Figure 2: The Ferm CDM1135 Cordless Screwdriver shown with its complete accessory kit, including the charger, various screw tips, and the angle and eccentric adapters.
5. Opsætning
5.1. Opladning af batteriet
The screwdriver is powered by an integrated 4V 1.5Ah Li-ion battery. Before first use, fully charge the battery.
- Connect the USB charging cable to the charging port on the screwdriver.
- Sæt den anden ende af USB-kablet i en kompatibel USB-strømadapter (medfølger ikke) eller en USB-port.
- The LED battery charge indicator will illuminate to show charging status. A full charge is indicated when all LED segments are lit or the indicator changes color (refer to specific LED behavior on your device).
- Når det er fuldt opladet, skal du frakoble ladekablet.
Note: Do not overcharge the battery. Unplug the charger once the battery is fully charged to prolong battery life.
5.2. Attaching Screw Tips and Adapters
The screwdriver features a magnetic chuck for quick and secure attachment of screw tips and adapters.
- Select the appropriate screw tip for your task.
- Insert the screw tip directly into the magnetic chuck until it is firmly seated.
- To attach an adapter (e.g., 45-degree angle adapter or edge strip adapter), align the adapter with the chuck and push it on until it clicks into place. Ensure it is securely fastened.
- To remove, pull the adapter or screw tip straight out from the chuck.
6. Betjeningsvejledning
6.1. Grundlæggende betjening
Before operating, ensure the battery is charged and the correct screw tip or adapter is installed.
- Rotation frem/tilbage: Locate the direction switch (usually near the trigger). Push it to the left for forward (tightening) rotation and to the right for reverse (loosening) rotation. Ensure the switch is in the neutral (middle) position when not in use to prevent accidental activation.
- Starting the Screwdriver: Press the trigger switch to activate the screwdriver. The double LED worklight will illuminate the work area automatically.
- Stopping the Screwdriver: Release the trigger switch to stop the screwdriver.
- Spindellås: When the trigger is released, the spindle automatically locks, allowing for manual tightening or loosening of screws if additional torque is required.
6.2. Using Adapters
The included adapters enhance the versatility of your screwdriver:
- 45-degree Angle Adapter: Use this adapter for driving screws in tight corners or confined spaces where a straight approach is not possible.
- Edge Strip Adapter: This adapter allows you to drive screws very close to an edge or surface, providing precise control in delicate applications.
Always ensure adapters are securely attached before use.
7. Vedligeholdelse
Regelmæssig vedligeholdelse sikrer optimal ydeevne og forlænger levetiden på dit værktøj.
- Rensning: Hold værktøjets ventilationsåbninger rene for at forhindre overophedning. Tør værktøjshuset af med en blød, tør klud.amp klæde. Brug ikke skrappe kemikalier eller slibende rengøringsmidler.
- Opbevaring: Store the screwdriver and its accessories in a dry, secure place, out of reach of children. Avoid storing in direct sunlight or extreme temperatures.
- Batteripleje: For long-term storage, charge the battery to approximately 50% and recharge every 3-6 months to prevent deep discharge.
8. Fejlfinding
If you encounter issues with your Ferm CDM1135 screwdriver, refer to the following common problems and solutions:
| Problem | Mulig årsag | Løsning |
|---|---|---|
| Skruetrækkeren tænder ikke. | Battery is discharged. Direction switch is in neutral position. | Charge the battery. Ensure the direction switch is set to forward or reverse. |
| Reduceret effekt eller kort driftstid. | Batteriet er lavt eller næsten ved slutningen af sin levetid. | Recharge the battery. If the problem persists after charging, the battery may need replacement (contact support). |
| Screw tip falls out. | Tip not fully inserted. Magnetic chuck is dirty. | Ensure tip is fully inserted into the magnetic chuck. Clean the magnetic chuck area. |
| Screwdriver overheats. | Blokerede ventilationsåbninger. Vedvarende kraftig brug. | Ensure ventilation openings are clear. Allow the tool to cool down during prolonged use. |
9. Specifikationer
| Feature | Specifikation |
|---|---|
| Model | CDM1135 |
| Mærke | Ferm |
| Strømkilde | Batteridrevet |
| Batteritype | 4V 1.5Ah Lithium-Ion (integrated) |
| Hastighed uden belastning | 0-200 RPM |
| Max drejningsmoment | 4 Newtonmeter |
| Chuck-type | Magnetisk |
| Vægt | 1.2 kilo |
| Dimensioner (LxBxH) | 28.5 x 26.5 x 26.5 cm |
| Inkluderede komponenter | Screwdriver, 28 Screw Tips, 2 Screwing Adapters, USB Charging Cable |
10. Garanti og support
Ferm products are manufactured to high-quality standards. In the unlikely event of a defect, please contact your retailer or the official Ferm customer support for assistance. Keep your proof of purchase for warranty claims. For detailed warranty terms and conditions, please refer to the warranty card included with your product or visit the official Ferm webwebsted.
For yderligere hjælp eller forespørgsler, besøg venligst Ferm official webwebsted eller kontakt deres kundeservice.
