1. Introduktion
This manual provides essential instructions for the safe operation, assembly, maintenance, and troubleshooting of your HECHT 135 BTS 2-stroke petrol brush cutter. Please read this manual thoroughly before using the equipment to ensure safe and efficient operation.
2. Sikkerhedsinstruktioner
Operating a petrol brush cutter requires strict adherence to safety guidelines to prevent injury. Always prioritize your safety and the safety of others.
2.1 Personligt beskyttelsesudstyr (PPE)
- Øjenbeskyttelse: Brug altid sikkerhedsbriller eller ansigtsskærm for at beskytte mod flyvende genstande.
- Høreværn: Brug ørepropper eller høreværn for at forhindre høreskader fra motorstøj.
- Håndbeskyttelse: Brug robuste arbejdshandsker for at forbedre grebet og beskytte hænderne.
- Fodbeskyttelse: Wear non-slip, steel-toed boots or sturdy footwear.
- Kropsbeskyttelse: Wear long pants and a long-sleeved shirt to protect skin from debris and sun. Avoid loose clothing that could get caught in moving parts.
2.2 Generelle sikkerhedsforanstaltninger
- Læs manualen: Forstå alle instruktioner og advarsler før brug.
- Area Inspection: Before starting, clear the work area of stones, metal objects, wires, and other debris that could be thrown or entangle the cutting head.
- Tilskuere: Keep all bystanders, children, and pets at a safe distance (at least 15 meters) from the operating area.
- Brændstofhåndtering: Handle petrol with extreme care. Refuel in a well-ventilated area with the engine off and cool. Do not smoke while refueling.
- Stabilt fodfæste: Hold altid et fast fodfæste og en fast balance. Ræk ikke for langt.
- Vejrforhold: Do not operate in rain or wet conditions, or when visibility is poor.
- Træthed: Do not operate the brush cutter when tired, ill, or under the influence of alcohol or drugs.
- Opretholdelse: Always turn off the engine and disconnect the spark plug before performing any maintenance, cleaning, or clearing blockages.
- Transportere: Transport the brush cutter with the engine off and the cutting attachment protected.
3. Pakkens indhold
Upon unpacking your HECHT 135 BTS brush cutter, verify that all components are present and undamaged:
- 1x HECHT 135 BTS Petrol Brush Cutter unit
- 1x 3-tooth Metal Blade (255 mm cutting width)
- 1x Dual-line Spool Head (430 mm cutting width)
- 1x Justerbar skulderrem
- 1x Handlebar assembly
- 1x Cutting Guard
- 1x Tool Kit (for assembly and basic maintenance)
- 1x brugermanual
4. Opsætning og montering
Follow these steps to assemble your brush cutter before first use.
4.1 Montering af styret
- Løsn styret clamp bolts on the main shaft.
- Position the handlebar onto the shaft at a comfortable working height and angle.
- Ensure all control cables are routed correctly and not pinched.
- Spænd clamp bolte sikkert.
4.2 Installing the Cutting Guard
- Slide the cutting guard onto the lower shaft, ensuring it is oriented correctly to protect against debris.
- Secure the guard with the provided screws or bolts. Do not operate the brush cutter without the guard properly installed.
4.3 Mounting the Cutting Head
Your HECHT 135 BTS comes with two interchangeable cutting heads: a 3-tooth metal blade and a dual-line spool head.
- Ensure the engine is off and the spark plug cap is removed.
- Insert the locking pin into the gearbox hole to prevent the shaft from rotating.
- For Metal Blade: Place the blade onto the shaft, ensuring it sits correctly on the support flange. Secure it with the washer and nut, tightening firmly (often left-hand thread).
- For Spool Head: Thread the spool head onto the shaft, turning clockwise until it is securely fastened.
- Fjern låsestiften.
4.4 Fastgørelse af skulderremmen
- Attach the shoulder strap to the designated hook or loop on the main shaft.
- Adjust the strap length so the cutting head is balanced and comfortable for your working posture, allowing for a slight bend in your arms.
4.5 Fueling the Brush Cutter
The HECHT 135 BTS uses a 2-stroke engine, requiring a specific petrol-oil mixture. Refer to the engine manufacturer's recommendations for the correct mixing ratio (typically 25:1 or 50:1, depending on the oil type).
- Use fresh, unleaded petrol and high-quality 2-stroke engine oil.
- Bland brændstoffet i en separat, godkendt brændstofbeholder.
- Sørg for, at motoren er slukket og afkølet, inden du påfylder brændstof.
- Carefully pour the mixed fuel into the fuel tank (capacity 0.7 L), avoiding spills.
- Luk tankdækslet forsvarligt.
5. Betjeningsvejledning
5.1 Start af motoren
- Placer buskrydderen på en plan, stabil overflade.
- Sæt tænd/sluk-kontakten i positionen 'TIL'.
- Aktiver chokeren (hvis motoren er kold).
- Tryk flere gange på primerpumpen, indtil brændstoffet er synligt.
- Hold the brush cutter firmly with one hand on the handlebar and the other on the starter grip.
- Pull the starter cord slowly until resistance is felt, then pull sharply and quickly until the engine fires (usually 1-3 pulls).
- Once the engine fires, disengage the choke (if applicable).
- Lad motoren varme op i et par øjeblikke, før du giver fuld gas.
5.2 Using the Brush Cutter
Hold the brush cutter firmly with both hands on the handlebar. Maintain a wide stance for balance. The shoulder strap should support the weight of the machine, allowing you to guide it with minimal effort.
- Skæreteknik: Use a sweeping motion from side to side. For dense growth, cut in smaller sections.
- Blade Use: Ideal for thick weeds, brush, and small saplings. Be aware of kickback when using the blade.
- Spool Head Use: Best for grass, light weeds, and trimming around obstacles. Advance the line as needed by tapping the head on the ground (tap-and-go system) or manually.
- Maintain RPM: Operate at a consistent, high RPM for efficient cutting and to prevent engine strain.
- Undgå forhindringer: Do not strike hard objects like rocks, fences, or concrete with the cutting head.
5.3 Standsning af motoren
- Release the throttle to allow the engine to idle.
- Move the ON/OFF switch to the 'OFF' position.
- Wait for all moving parts to come to a complete stop before setting the machine down.
6. Vedligeholdelse
Regular maintenance ensures the longevity and safe operation of your HECHT 135 BTS brush cutter.
6.1 Efter hver brug
- Rengør enheden: Remove grass, dirt, and debris from the engine, cutting head, and guard. Use a brush or compressed air.
- Inspect Cutting Head: Check the blade for sharpness and damage, or the line spool for wear and proper function. Replace or sharpen as needed.
- Kontroller fastgørelseselementer: Sørg for, at alle møtrikker, bolte og skruer er stramme.
6.2 Periodisk vedligeholdelse
- Luftfilter: Clean the air filter regularly (every 5-10 hours of operation, more often in dusty conditions). Wash foam filters in warm, soapy water, rinse, dry, and lightly oil. Replace paper filters if heavily soiled.
- Tændrør: Inspect the spark plug every 20-30 hours. Clean carbon deposits and adjust the gap if necessary. Replace if electrodes are worn or damaged.
- Brændstoffilter: Inspect and replace the fuel filter in the tank annually or if fuel flow issues occur.
- Smøring af gearkasse: Check and replenish the grease in the gearbox (at the cutting head end) as per manufacturer recommendations, typically every 25-50 hours.
- Køleribber: Hold motorens køleribber rene for at forhindre overophedning.
6.3 Opbevaring
- Ved langtidsopbevaring skal brændstoftanken tømmes og motoren køres, indtil den stopper, for at tømme karburatoren for brændstof.
- Rengør hele enheden grundigt.
- Store in a dry, well-ventilated area, away from direct sunlight and heat sources.
7. Fejlfinding
Dette afsnit omhandler almindelige problemer, du kan støde på med din buskrydder.
| Problem | Mulig årsag | Løsning |
|---|---|---|
| Motoren vil ikke starte | No fuel, incorrect choke, fouled spark plug, clogged fuel filter, old fuel. | Check fuel level and mixture. Adjust choke. Clean/replace spark plug. Clean/replace fuel filter. Use fresh fuel. |
| Tab af strøm under drift | Clogged air filter, incorrect fuel mixture, dull cutting head, engine overheating. | Clean air filter. Verify fuel mixture. Sharpen/replace cutting head. Clean cooling fins. |
| Overdreven vibration | Damaged or unbalanced cutting head, loose fasteners, bent shaft. | Inspect and replace damaged cutting head. Tighten all fasteners. If shaft is bent, seek professional service. |
| Skæretråden går ikke fremad | Line tangled, insufficient line, incorrect spool installation. | Turn off engine, clear tangles, reload line, ensure spool is correctly installed. |
8. Specifikationer
Technical data for the HECHT 135 BTS Petrol Brush Cutter:
- Motortype: 2-takts, enkelt cylinder
- Forskydning: 33 cm³
- Nominel effekt: 0.9 kW / 1.2 HK
- Max. Engine Power: 1.1 kW / 1.5 HK
- Nominel motorhastighed: 6500 rpm
- Maks. Motorhastighed: 13000 rpm
- Brændstoftankvolumen: 0.7 L
- Blade Cutting Width: 255 mm (25.5 cm)
- Line Cutting Width: 430 mm (43 cm)
- Max. Line Thickness: 2.5 mm
- Max. Spool Head Speed: 8500 rpm
- Nettovægt: 6.1 kg
- Samlet længde: 1880 mm
- Samlet bredde: 720 mm
- Samlet højde: 400 mm
9. Produktbilleder
Visual references for the HECHT 135 BTS Brush Cutter.
Billedbeskrivelse: This is a placeholder image indicating 'No image available'. A typical product image would show the HECHT 135 BTS 2-stroke petrol brush cutter fully assembled, highlighting its handlebar, engine unit, and interchangeable cutting heads (3-tooth blade and line spool).
10. Garanti og support
Ved garantikrav, teknisk support eller forespørgsler om reservedele bedes du kontakte din forhandler eller producenten direkte. Gem din købsbevis for at validere garantien.
Note: Information regarding the availability of spare parts for this product is currently unavailable.
