1. Introduktion
This manual provides essential information for the safe and effective operation, setup, and maintenance of your FERM TDM1026 Pillar Drill. Please read these instructions carefully before using the machine to ensure proper function and to prevent injury or damage.
Image 1: The FERM TDM1026 Pillar Drill, showcasing its robust construction and key components.
2. Sikkerhedsinstruktioner
Overhold altid grundlæggende sikkerhedsforanstaltninger for at reducere risikoen for brand, elektrisk stød og personskade. Gem denne manual til senere brug.
- Sikkerhed på arbejdsområdet: Hold arbejdsområdet rent og godt oplyst. Rodede eller mørke områder indbyder til ulykker. Brug ikke elværktøj i eksplosive atmosfærer, f.eks. i nærheden af brandfarlige væsker, gasser eller støv.
- Elektrisk sikkerhed: Stik på elværktøj skal passe til stikkontakten. Modificer aldrig stikket på nogen måde. Undgå kropskontakt med jordforbundne overflader, såsom rør, radiatorer, komfurer og køleskabe.
- Personlig sikkerhed: Always wear eye protection. Use hearing protection when operating the drill for extended periods. Do not overreach. Maintain proper footing and balance at all times.
- Brug og pleje af værktøj: Tving ikke elværktøjet. Brug det korrekte elværktøj til din anvendelse. Tag stikket ud af strømkilden, før du foretager justeringer, skifter tilbehør eller opbevarer elværktøj.
- Nødstop: The machine is equipped with a red emergency stop button for immediate shutdown.
- Sikkerhedsvagt: A transparent safety guard is provided over the chuck area to protect against flying debris. Ensure it is always in place during operation.
3. Opsætning
3.1 Udpakning og montering
Carefully remove all components from the packaging. Ensure all parts listed in the packing contents are present. Assemble the pillar drill according to the provided assembly diagram (not included in this document, refer to separate assembly sheet if applicable).
3.2 Mounting the Drill
The drill press features pre-drilled holes in its base for secure mounting to a workbench. This is highly recommended to ensure stability and safety during operation.
3.3 Justering af arbejdsbordet
The 160x160mm work table can be adjusted in height and tilted from -45° to 45°. Loosen the locking mechanism to adjust the table to the desired height and angle, then securely tighten it before drilling.
Image 2: Close-up of the adjustable work table and its angle indicator.
3.4 Installing the Drill Bit
The drill is equipped with a keyed chuck for securing various types of drill bits up to 13mm in diameter. Insert the drill bit into the chuck and tighten it firmly using the provided chuck key. Ensure the bit is centered and secure.
Image 3: The chuck key being used to tighten a drill bit in the chuck.
4. Betjeningsvejledning
4.1 Tænd/sluk
The drill press features a main power switch. Press the green button to turn the machine on and the red button to turn it off. In case of emergency, press the large red emergency stop button.
Image 4: The main power switch with green 'on' and red 'off' buttons.
4.2 Justering af hastighedsindstillinger
The FERM TDM1026 offers 5 different speed settings (500, 890, 1400, 1900, 2500 RPM). To change the speed, open the metal belt housing on top of the drill. Adjust the V-belt position on the pulleys to achieve the desired speed. Refer to the diagram inside the housing for correct belt placement. Ensure the machine is unplugged before adjusting the belt.
Image 5: The belt drive system for adjusting drilling speeds.
4.3 Indstilling af boredybde
Utilize the drilling depth stop to precisely control the depth of your drill hole, up to a maximum of 52mm. Adjust the depth stop mechanism to the required depth before starting the drilling operation.
Image 6: Close-up of the depth stop mechanism with measurement scale.
4.4 Boreoperation
Secure the workpiece firmly to the work table using clamps if necessary. Lower the drill bit slowly into the material using the feed handles. Apply steady, even pressure. The transparent safety guard provides visibility while protecting against debris.
Image 7: The pillar drill in use, demonstrating a drilling operation on a wooden workpiece.
Image 8: The transparent safety guard covering the drill chuck area.
5. Vedligeholdelse
Regular maintenance ensures the longevity and safe operation of your pillar drill. Always disconnect the power supply before performing any maintenance.
- Rensning: Keep the machine clean, especially the work table and column, to prevent accumulation of dust and debris. Use a dry cloth or soft brush.
- Smøring: Smør de bevægelige dele regelmæssigt som angivet i den detaljerede servicemanual (hvis relevant).
- Bælteinspektion: Regularly check the V-belt for wear and proper tension. Adjust or replace if necessary.
- Vedligeholdelse af borepatron: Hold spændepatronens kæber rene og fri for snavs for at sikre korrekt greb om borehovederne.
6. Fejlfinding
This section addresses common issues you might encounter with your pillar drill.
- Maskinen starter ikke:
- Kontroller, om netledningen er tilsluttet korrekt til en funktionel stikkontakt.
- Ensure the main power switch is in the 'on' position.
- Verify that the belt housing cover is fully closed, as a safety interlock prevents operation when open.
- Check if the emergency stop button is engaged; twist to release if pressed.
- For kraftig vibration under drift:
- Ensure the drill bit is properly installed and tightened in the chuck.
- Check the V-belt tension and condition. A loose or worn belt can cause vibration.
- Verify that the machine is securely mounted to the workbench.
- Drill bit not cutting effectively:
- Ensure the drill bit is sharp and appropriate for the material being drilled.
- Check that the correct speed setting is selected for the material and drill bit size.
- Apply adequate, but not excessive, downward pressure.
7. Specifikationer
| Feature | Specifikation |
|---|---|
| Model | TDM1026 |
| Strømindgang | 350 W |
| Voltage | 230 V |
| Frekvens | 50 Hz |
| Antal hastigheder | 5 (500, 890, 1400, 1900, 2500 RPM) |
| Arbejdsbord størrelse | 160 x 160 mm |
| Bordhældningsvinkel | -45° til 45° |
| Maks. borepatronkapacitet | 13 mm |
| Maks. Boredybde | 52 mm |
| Max. Spindle to Table Distance | 215 mm (lowest position) |
| Max. Spindle to Base Distance | 303 mm |
| Samlet højde | 600 mm |
| Strømkabellængde | 2 m |
| Vægt | 13.7 kg |
| Dimensioner (L x B x H) | 44 x 36 x 23 cm |
8. Garanti og support
For warranty information, technical support, or spare parts availability, please refer to the documentation provided with your purchase or contact FERM customer service directly. Specific details regarding warranty periods and service procedures are not included in this general instruction manual.
