Fuers TL-2600 Fake Camera Instruction Manual

1. Produktet er slutview

The Fuers TL-2600 is a high-quality, durable dummy surveillance camera designed to deter potential intruders. It features a realistic appearance, a flashing LED light, and is suitable for both indoor and outdoor use. This device provides a cost-effective solution to enhance security visibility without the complexity of a real surveillance system.

Nøglefunktioner:

• Realistisk design: High resemblance to actual security cameras.
• Blinkende LED lys: Simulates active surveillance, powered by 2 AAA batteries (not included).
• Holdbar konstruktion: Made from high-quality ABS material, weather-resistant for outdoor use.
• Justerbar vinkel: Features a mounting bracket allowing for 90° vertical and 360° horizontal rotation.
• Nem installation: No wiring required, mounts quickly to walls or ceilings.

Image 1.1: The Fuers TL-2600 Fake Camera featuring a red flashing LED light, simulating active operation.

Image 1.2: The camera's adjustable bracket allows for 90-degree vertical and 360-degree horizontal rotation for optimal positioning.

2. Pakkens indhold

Kontroller venligst, at alle nedenstående varer er inkluderet i din pakke:

• 1 x Fuers TL-2600 Dummy Camera Unit
• 1 x monteringsbeslag (formonteret)
• 3 x monteringsskruer
• 3 x Vægstik
• 1 x CCTV Warning Sticker

Note: 2 x AAA batteries are ikke inkluderet og skal købes separat.

Image 2.1: Contents of the package including the dummy camera, mounting hardware, and a CCTV sticker. Dimensions are also shown.

3. Opsætning

3.1 Batteriinstallation

1. Locate the battery compartment on the underside of the camera body.
2. Åbn forsigtigt dækslet til rummet.
3. Sæt to (2) AAA-batterier (medfølger ikke) i batterirummet, og sørg for at polerne vender korrekt (+/-).
4. Close the battery compartment cover securely. The LED light should begin flashing immediately.

Billede 3.1: View of the battery compartment opened to insert two AAA batteries.

Image 3.2: Step-by-step guide for installing batteries into the dummy camera.

3.2 Montering af kameraet

1. Choose a suitable location for installation, such as a wall or ceiling, ensuring good visibility and deterrence.
2. Position the mounting bracket at the desired location and mark the three screw holes.
3. Drill pilot holes at the marked spots. For masonry or drywall, insert the provided wall plugs.
4. Fastgør monteringsbeslaget til overfladen med de medfølgende skruer.
5. Adjust the camera angle as needed (refer to Section 4.1).
6. Affix the included CCTV warning sticker in a prominent location nearby to further enhance deterrence.

4. Betjeningsvejledning

4.1 Adjusting Camera Angle

The camera's mounting bracket allows for flexible positioning:

• Lodret justering: Loosen the side screw on the bracket to tilt the camera up or down (up to 90°). Tighten the screw once the desired angle is achieved.
• Vandret justering: The base of the bracket allows for full 360° rotation. Simply rotate the camera body to face the desired direction.

4.2 LED blinker

Once batteries are correctly installed, the red LED light will automatically begin to flash continuously. There is no separate on/off switch for the LED. The flashing LED simulates the operation of a real security camera, enhancing its deterrent effect.

5. Vedligeholdelse

• Udskiftning af batteri: Replace the two AAA batteries when the LED light stops flashing or becomes dim. Always use fresh batteries for optimal performance.
• Rensning: Wipe the camera body and lens area with a soft, damp klud til at fjerne støv og snavs. Undgå at bruge skrappe kemikalier eller slibende rengøringsmidler.
• Vejrbestandighed: While designed for outdoor use, extreme weather conditions (e.g., heavy storms, prolonged direct sunlight) may affect its lifespan. Periodically check the unit for any signs of wear or damage.

6. Fejlfinding

• LED blinker ikke:
  • Kontroller, om batterierne er installeret korrekt med den rigtige polaritet.
  • Udskift med nye AAA-batterier.
• Camera Feels Loose After Mounting:
  • Sørg for, at alle monteringsskruer er spændt forsvarligt.
  • If mounted on drywall, ensure wall plugs are properly seated.

7. Specifikationer