1. Introduktion
The Godox XproF is a versatile TTL wireless flash trigger designed for Fujifilm cameras, offering advanced control over your lighting setup. This manual provides detailed instructions for setting up, operating, and maintaining your XproF trigger to ensure optimal performance.
Key features include TTL Autoflash, 1/8000s High-Speed Sync (HSS), Multi Flash, Manual Flash, Flash Exposure Compensation, and the innovative TCM (TTL-Convert-Manual) function. It supports 16 groups and 32 channels for wireless control, features a large dot matrix LCD for simultaneous display of 5 groups, and offers 11 customizable functions for tailored operation.
The XproF also includes a magnification function to display detailed group settings, global adjustments for exposure values in M mode across multiple groups, and selective data transmission to conserve energy. Firmware upgrades are supported via a Type-C USB port, and wireless triggering is possible via a 2.5mm sync cord jack.
2. Opsætning
2.1. Batteriinstallation
The Godox XproF requires two AA batteries for operation. To install the batteries, slide open the battery compartment cover located on the underside of the unit. Insert two AA batteries, ensuring correct polarity (+/-), then close the cover securely.
Figure 2.1: Battery compartment of the Godox XproF, showing two AA batteries correctly inserted. The compartment is located on the underside of the unit.
2.2. Montering på kamera
To mount the XproF on your Fujifilm camera, slide the hot shoe foot of the trigger into the camera's hot shoe. Secure the trigger by rotating the locking ring clockwise until it is firmly attached. Ensure the trigger is securely fastened to prevent accidental detachment during use.
Figure 2.2: The Godox XproF trigger securely mounted on the hot shoe of a Fujifilm camera, ready for operation.
Video 2.1: A demonstration of installing batteries and mounting the Godox XPro TTL Wireless Flash Trigger Transmitter onto a camera. This video shows the physical attachment process and initial power-up.
3. Betjeningsvejledning
3.1. Tænd/sluk
To power on the XproF, slide the power switch located on the side of the unit to the 'ON' position. The LCD screen will illuminate. To power off, slide the switch to the 'OFF' position.
3.2. Interface overview
The XproF features a large dot matrix LCD display and dedicated buttons for intuitive control. The left side of the screen displays five group buttons (A-E), while the bottom features four function buttons (MODE, RST, MENU, TCM) and a central SET dial.
Figur 3.1: Forside view of the Godox XproF, highlighting the large LCD screen and the arrangement of group and function buttons for easy access to settings.
3.3. Group and Channel Control
The XproF supports 16 groups and 32 channels. Use the group buttons (A-E) to select individual flash groups. The central SET dial allows for quick adjustment of power output and other parameters within the selected group. The CH/Zm button allows you to change channels.
3.4. TTL Autoflash and Manual Flash
The trigger supports TTL Autoflash for automatic exposure control and Manual Flash for precise power adjustments from 1/1 to 1/256. Use the MODE button to switch between TTL, Manual, and Multi-Flash modes.
3.5. Højhastighedssynkronisering (HSS)
Achieve shutter speeds up to 1/8000s with High-Speed Sync. This function is accessible through the menu settings or dedicated buttons, allowing for creative control over ambient light.
3.6. TCM (TTL-Convert-Manual) Function
The SMART TCM button allows you to convert the flash value from TTL mode into a power output value in Manual mode. A long press of the TCM button performs this conversion, while a short press switches groups between one-group and multi-group mode.
Figure 3.2: Visual representation of the TCM function, illustrating how a long press on the TCM button translates TTL flash values into manual power settings.
3.7. Indstillinger for trådløst ID
To avoid signal interference, the XproF allows you to set a Wireless ID (01-99). Triggering will only occur when the channels and Wireless IDs of both the master (XproF) and slave units are identical.
Figure 3.3: The XproF display showing options for custom functions, including the 01-99 Wireless ID setting to prevent interference.
3.8. Modellering af Lamp Kontrollere
Styr modelleringen lamp status of your flash units directly from the XproF. This allows you to preview lyseffekter før du tager et billede.
3.9. Adjusting Flash Zoom Coverage
The XproF enables you to adjust the flash zoom coverage for each group, providing precise control over the spread of light.
3.10. Låsefunktion
To prevent accidental changes to settings, the XproF features a locking function. This can be activated or deactivated through the menu or by pressing the power switch.
3.11. Multi-Flash Setting
The Multi-Flash setting allows for stroboscopic effects, firing the flash multiple times during a single exposure. This can be configured via the menu options.
3.12. Custom Function Settings
The XproF offers 11 customizable functions to tailor the trigger's behavior to your specific needs. These settings can be accessed and adjusted through the MENU button.
Video 3.1: An operation video demonstrating various functions of the Godox X3 TTL Wireless Flash Trigger, including power adjustment, group selection, and mode switching. While showing the X3, the core operational principles are similar to the XproF.
Video 3.2: A usage demonstration of the Godox XProII TTL Wireless Flash Trigger, showcasing its interface and how to adjust settings. This video provides a visual guide to the trigger's functionality, which is largely consistent with the XproF.
4. Vedligeholdelse
4.1. Firmware -opgradering
The Godox XproF supports firmware upgrades via its Type-C USB port. Regularly check the official Godox website for the latest firmware versions to ensure optimal performance and access to new features. Follow the instructions provided with the firmware update file for a successful upgrade.
4.2. Almen pleje
Keep the trigger clean and dry. Avoid exposing it to extreme temperatures, humidity, or direct sunlight. Use a soft, dry cloth for cleaning. Do not use harsh chemicals or abrasive materials.
5. Fejlfinding
5.1. Flash Not Firing
- Ensure the XproF is securely mounted on the camera's hot shoe.
- Verify that both the XproF and the slave flash units are powered on.
- Check that the channel and Wireless ID settings on the XproF and all slave units match.
- Confirm that the batteries in both the trigger and flash units have sufficient power.
- Ensure the flash mode (TTL, Manual, Multi) is correctly set on both the trigger and slave units.
5.2. Signal Interference
- Change the channel and Wireless ID to a different combination to avoid interference from other wireless devices.
- Ensure there are no large metallic objects or other sources of strong electromagnetic interference between the trigger and the flash units.
5.3. Skærmen reagerer ikke
- Check if the screen locking function is active. Unlock the screen by pressing the power switch or through the menu.
- Restart the unit by powering it off and then on again.
- Ensure the batteries are properly inserted and charged.
6. Specifikationer
- Produktdimensioner: 2.76 x 2.76 x 1.97 tommer
- Varens vægt: 5.3 ounce
- Varemodelnummer: XProF for Fujifilm
- Mærke: GODOX
- Kompatible monteringer: Fujifilm
- Kamera Flash: Slave
- Flash-synkroniseringshastighed: 1/8000s
7. Hvad er der i æsken
- 1X GODOX XPRO Flash Trigger
- 1X Cleaning Cloth
8. Garanti og support
For garantioplysninger og teknisk support henvises til den dokumentation, der følger med dit produkt, eller besøg den officielle GODOX webwebsted. Behold din købskvittering som købsbevis i tilfælde af garantikrav.
