Lutron LECL-153PH-LA X-10 Kompatibel Lysdæmper Brugermanual

Indledning

This manual provides detailed instructions for the safe installation, operation, and maintenance of your Lutron LECL-153PH-LA X-10 Compatible Dimmer Switch. This device is designed to control incandescent, halogen, and certain fluorescent lighting loads up to 600 watts at 120 Volts, utilizing X-10 powerline communication for dimming and switching functions. Please read all instructions thoroughly before proceeding with installation or use.

Vigtige sikkerhedsoplysninger

• ADVARSEL: For at undgå brand, stød eller dødsfald skal du slukke for strømmen ved afbryderen eller sikringsboksen og kontrollere, at strømmen er afbrudt, før du tilslutter ledninger.
• Installer i overensstemmelse med alle nationale og lokale elektriske koder.
• This dimmer is for use with permanently installed incandescent, halogen, or compatible fluorescent fixtures only. Do not use with low-voltage lighting with a magnetic transformer, motor-driven appliances, or non-dimmable fluorescent fixtures.
• Kun til indendørs brug.
• Hvis du er i tvivl om nogen del af disse instruktioner, skal du kontakte en kvalificeret elektriker.

Pakkens indhold

• Lutron LECL-153PH-LA X-10 Compatible Dimmer Switch (Light Almond)
• Mounting Screws (typically included)
• Wire Connectors (typically included)
• Instruktionsmanual (dette dokument)

Billede: Forside view of the Lutron LECL-153PH-LA X-10 Compatible Dimmer Switch in Light Almond color, showing the rocker switch and slide dimmer control.

Specifikationer

Installation (Opsætning)

This dimmer is an X-10 compatible device. Proper installation requires understanding of both standard electrical wiring and X-10 addressing. If you are unfamiliar with X-10 systems, please consult an X-10 expert or a qualified electrician.

Nødvendige værktøjer:

• Skruetrækkere (Phillips og flathead)
• Afisoleringstænger
• Elektrisk tape
• Voltage tester

Ledningsinstruktioner:

1. Sluk for strømmen: Locate the circuit breaker or fuse that controls the light switch you are replacing. Turn it OFF. Verify power is off at the switch box using a voltage tester.
2. Fjern eksisterende switch: Fjern forsigtigt vægpladen, og skru den eksisterende afbryder af vægdåsen. Frakobl ledningerne fra den gamle afbryder.
3. Identificér ledninger:
   • Line/Hot Wire: Fører strøm fra afbryderen.
   • Indlæs ledning: Forbindes til lysarmaturet.
   • Neutral ledning: (If present, typically white) Not always required for dimmers, but check dimmer specifications.
   • Jordledning: (Bare copper or green) Connects to the metal electrical box or ground wire bundle.
   • Traveler Wires: (For 3-way installations, typically red or black) Connects between two switches controlling the same light.
4. Connect the Dimmer:
   • Tilslut jordledning from the wall box to the green or bare copper wire on the dimmer.
   • Tilslut Line/Hot wire to the designated Line terminal on the dimmer.
   • Tilslut Læg ledning i to the designated Load terminal on the dimmer.
   • Ved 3-vejs installationer skal du tilslutte traveler wires to the appropriate traveler terminals on both the dimmer and the companion switch. Refer to the specific wiring diagram provided with your dimmer for 3-way configurations.
   • Ensure all wire connections are secure using wire connectors.
5. Set X-10 Address: Before mounting, set the X-10 House Code and Unit Code on the dimmer. This is typically done via small rotary switches or dip switches on the dimmer module. Refer to the specific instructions on the dimmer itself or a separate X-10 setup guide for your system.
6. Monter lysdæmperen: Carefully fold the wires into the wall box and secure the dimmer to the box with the provided screws.
7. Installer vægplade: Fastgør vægpladen.
8. Gendan strøm: Tænd for strømmen igen ved afbryderen.

Operation

The Lutron LECL-153PH-LA dimmer switch offers both manual control and X-10 powerline control.

Manuel kontrol:

• Til/fra: Press the bottom rocker switch to turn the lights ON or OFF.
• Dæmpning: Use the vertical slide control to adjust the light level. Slide up to brighten, slide down to dim.

X-10 Control:

Once the X-10 House Code and Unit Code are set, the dimmer will respond to X-10 commands sent over the powerline from an X-10 controller (e.g., a remote, wall-mounted keypad, or computer interface). Common X-10 commands include:

• "PÅ": Turns the light on to the last set dim level or full brightness.
• "SLUKKET": Slukker lyset.
• "BRIGHT": Gradually brightens the light.
• "DIM": Gradually dims the light.

Refer to your X-10 system's documentation for specific programming and command details.

Opretholdelse

• Rensning: For at rengøre lysdæmperen skal du tørre den af ​​med en blød klud.amp klud. Brug ikke kemiske rengøringsmidler eller slibende materialer.
• Ingen dele, der kan serviceres af brugeren: There are no user-serviceable parts inside the dimmer. Do not attempt to open or repair the unit.

Fejlfinding

Garanti og support

This Lutron product is covered by a warranty. For detailed warranty information, please refer to the warranty card included with your product or visit the official Lutron website. For technical support, troubleshooting assistance, or to inquire about replacement parts, please contact Lutron customer service directly.

Lutron Webwebsted: www.lutron.com