BLS T01L LED-skabslampe brugermanual

1. Introduktion

The BLS T01L LED Closet Light is a versatile, motion-sensing lighting solution designed for various indoor applications. It features 20 super bright LEDs, offering 180 lumens of soft white light. This light can be powered by 3 AA batteries for wireless operation or via a 5V USB DC input for constant lighting. Its adjustable light beam and motion sensor provide customizable illumination and detection.

Image 1.1: The BLS T01L LED Closet Light, a 14-inch white light bar with a central motion sensor.

2. Hvad er der i æsken

Kontroller venligst, at alle komponenter er til stede, når du åbner pakken:

• 1 x BLS Under Cabinet Light (Model T01L)
• 1 x DC kabel
• 2 x 3M klæbebånd
• 1 x Brugsanvisning (dette dokument)

Image 2.1: The BLS T01L LED Closet Light shown with its packaging, DC cable, and mounting accessories.

3. Specifikationer

4. Opsætning og installation

Follow these steps to set up your BLS T01L LED Closet Light:

4.1. Strømforsyning til enheden

The light can be powered by 3 AA batteries or a 5V USB DC input.

1. Batteri installation:
   • Locate the battery compartment on the back of the light.
   • Gently push to open the center part of the battery compartment cover.
   • Insert three AA batteries (not included). One battery slides into the hole on the left, the second into the hole on the right, and the third goes into the open center between the first two. Ensure correct polarity (+/-).
   • Luk batterirummets dæksel forsvarligt.
2. USB DC Power:
   • Connect the provided DC cable to the light's DC input port.
   • Plug the other end of the DC cable into a 5V USB power source (e.g., USB wall adapter, power bank).
   • Note: If using USB DC power, it is recommended to remove the AA batteries to prevent potential issues or unnecessary battery drain.

Image 4.1: Diagram illustrating the 14-inch length of the light and its power options: 3 AA batteries or USB cable.

4.2. Montering af lyset

The BLS T01L offers multiple installation options:

• Klæbende montering: Peel the backing from the 3M adhesive tapes and firmly press the light onto a clean, dry surface.
• Skrue montering: Use the provided screws to secure the light to the desired surface. This method offers a more permanent installation.

The light can be mounted either horizontally or vertically, depending on your application needs.

Image 4.2: Diagram showing horizontal and vertical installation options using screws or 3M adhesive stickers.

5. Betjeningsvejledning

5.1. Valg af tilstand

The light features a slide switch with three modes:

• AUTO-tilstand: The light will automatically turn on when motion is detected within 10 feet in a dark environment. It will remain on for 20 seconds after motion ceases. The built-in light sensor ensures it only activates when ambient light is low (e.g., at night).
• TIL-tilstand: Lyset vil forblive tændt konstant, uanset bevægelse eller omgivende lysforhold.
• FRA -tilstand: Lyset vil forblive slukket.

5.2. Adjusting Motion Sensor Sensitivity

The motion sensor can be adjusted to modify its detection sensitivity and range:

• The motion sensor module is designed to swivel. Gently rotate the sensor to adjust its detection angle.
• This allows you to fine-tune the area where motion is detected, preventing unwanted activations.

Image 5.1: Illustration of how to adjust the motion sensor to control sensitivity.

5.3. Adjusting Light Beam Angle

The entire light fixture can be adjusted to direct the light beam as desired:

• The light is mounted on a bracket that allows it to swivel.
• Gently pivot the light to achieve the desired illumination angle (e.g., 90°, 120°, 180°).

Billede 5.2: Eks.amples of adjustable light beam angles (90°, 120°, 180°) for optimal illumination.

6. Vedligeholdelse

6.1. Udskiftning af batteri

When the light output diminishes or the motion sensor becomes less responsive, it may be time to replace the batteries.

1. Åbn batteridækslet som beskrevet i afsnit 4.1.
2. Fjern de gamle AA-batterier.
3. Isæt tre nye AA-batterier, og sørg for at polariteten vender korrekt.
4. Luk batterirummets dæksel.

Note: For optimal performance and to avoid frequent battery changes, consider using high-quality alkaline or rechargeable AA batteries. If using the USB DC power option, remove the AA batteries.

6.2. Rensning

For at bevare din lampes udseende og funktionalitet:

• Ensure the light is in the OFF position or disconnected from power before cleaning.
• Tør overfladen af ​​med en blød, tør klud.
• Brug ikke slibende rengøringsmidler, opløsningsmidler eller stærke kemikalier, da disse kan beskadige overfladen eller de elektroniske komponenter.

7. Fejlfinding

If you encounter issues with your BLS T01L LED Closet Light, refer to the following common problems and solutions:

8. Garantioplysninger

The BLS T01L LED Closet Light comes with an extended warranty. For specific details regarding warranty coverage, terms, and conditions, please refer to the warranty card included with your product or contact BLS customer support.

9. Kundesupport

If you have any questions, require technical assistance, or need further support, please contact BLS customer service through the following channels:

• E-mail: Refer to your product packaging or the official BLS webwebsted for den seneste kontakt-e-mail.
• Webwebsted: Visit the official BLS webwebsted for ofte stillede spørgsmål og supportressourcer.
• Amazon Store: Du kan også besøge BLS Store on Amazon for product information and seller contact options.