STRONG Powerline Wi-Fi 500 Duo Kit Brugermanual

Indledning

This manual provides comprehensive instructions for the installation, operation, and maintenance of your STRONG Powerline Wi-Fi 500 Duo Kit. This kit allows you to extend your internet network using your home's existing electrical wiring, providing both wired Ethernet and wireless Wi-Fi connectivity.

Figure 1: STRONG Powerline Wi-Fi 500 Duo Kit components.

Pakkens indhold

• 1x Powerline Wi-Fi 500 Adapter (with antennas)
• 1x Powerline 500 Adapter (with pass-through socket)
• 2x Ethernet RJ45 Cables
• 1x hurtig installationsvejledning

Figure 2: Packaging of the STRONG Powerline Wi-Fi 500 Duo Kit.

Opsætningsvejledning

1. Initial Placement and Connection

For optimal performance, plug the Powerline adapters directly into a wall outlet. Avoid power strips, surge protectors, or extension cords, as these can interfere with the Powerline signal.

1. Connect the Main Adapter: Plug the Powerline 500 Adapter (the one without antennas, with the pass-through socket) into a wall outlet near your internet router. Connect one end of an Ethernet cable to a LAN port on your router and the other end to the Ethernet port on this Powerline adapter.
2. Connect the Wi-Fi Adapter: Plug the Powerline Wi-Fi 500 Adapter (the one with antennas) into a wall outlet in the room where you need extended Wi-Fi or wired internet access.

Figure 3: Basic Powerline network setup diagram.

2. Pairing the Adapters

The adapters should automatically pair. If they do not, or if you are adding new adapters to an existing Powerline network, follow these steps:

1. Press the "Pair" button on the Powerline 500 Adapter (the one connected to your router) for 2 seconds. The Power LED will start blinking.
2. Within 2 minutes, press the "Pair" button on the Powerline Wi-Fi 500 Adapter (the one with antennas) for 2 seconds. The Power LED will also start blinking.
3. Wait for a few moments. The Power LEDs on both adapters should turn solid green, indicating a successful connection. The House icon LED on both units should also illuminate.

3. Wi-Fi-konfiguration

The Powerline Wi-Fi 500 Adapter broadcasts a Wi-Fi network. The default Wi-Fi network name (SSID) and password are printed on a label on the adapter itself.

• Opret forbindelse til Wi-Fi: On your Wi-Fi enabled device (smartphone, tablet, laptop), search for available Wi-Fi networks. Select the network name (SSID) corresponding to your Powerline Wi-Fi 500 Adapter.
• Indtast adgangskode: Enter the Wi-Fi password (WPA/WPA2-PSK) found on the adapter's label.
• Optional: Clone Wi-Fi Settings: To seamlessly extend your existing Wi-Fi network, you can use the Wi-Fi Clone function. Press the WPS button on your main router, then within 2 minutes, press the Wi-Fi Clone button on the Powerline Wi-Fi 500 Adapter. This will copy your router's SSID and password to the Powerline adapter.

Figure 4: Powerline Wi-Fi 500 Adapter front panel with indicators and buttons.

Betjeningsvejledning

LED-indikatorer

Tilslutning af enheder

Once the Powerline network is established, you can connect devices:

• Kablet forbindelse: Use an Ethernet cable to connect devices like desktop computers, smart TVs, gaming consoles, or network printers to the LAN ports on the Powerline Wi-Fi 500 Adapter.
• Trådløs forbindelse: Connect Wi-Fi enabled devices (smartphones, tablets, laptops) to the Wi-Fi network broadcast by the Powerline Wi-Fi 500 Adapter using the configured SSID and password.

Figur 5: Eksample of devices connected via Powerline adapter.

Figure 6: Powerline adapters in typical home and office environments.

Figure 7: Powerline Wi-Fi adapter highlighting 500 Mbps speed.

Opretholdelse

The STRONG Powerline Wi-Fi 500 Duo Kit requires minimal maintenance. Follow these guidelines to ensure optimal performance and longevity:

• Rensning: Use a soft, dry cloth to clean the exterior of the adapters. Do not use liquid cleaners or aerosols.
• Ventilation: Ensure that the ventilation slots on the adapters are not blocked. Adequate airflow is essential to prevent overheating.
• Firmwareopdateringer: Tjek regelmæssigt den officielle STRONG-ansvarlige website for any available firmware updates for your model. Firmware updates can improve performance, add features, or fix bugs.
• Strømbesparelsestilstand: The adapters are designed to enter a power-saving mode when no data is being transmitted, reducing energy consumption.

Figure 8: Power-saving feature illustration.

Fejlfinding

If you encounter issues with your Powerline Wi-Fi 500 Duo Kit, refer to the following common problems and solutions:

• No Powerline Connection (House LED Off):
  • Sørg for, at begge adaptere er tilsluttet direkte til stikkontakter, ikke til strømskinner eller forlængerledninger.
  • Prøv at tilslutte adapterne til forskellige stikkontakter inden for det samme elektriske kredsløb.
  • Perform the pairing process again as described in the "Setup Guide" section.
  • Check for electrical interference from other high-power appliances.
• No Internet Access via Powerline:
  • Bekræft, at din primære router har en aktiv internetforbindelse.
  • Ensure the Ethernet cable connecting the main Powerline adapter to the router is securely plugged in.
  • Check the Ethernet LED on the Powerline adapter to confirm a wired connection to your device.
• Wi-Fi Not Broadcasting or Accessible:
  • Ensure the Wi-Fi LED on the Powerline Wi-Fi 500 Adapter is solid green.
  • Verify you are entering the correct Wi-Fi SSID and password.
  • If you used Wi-Fi Clone, ensure the cloning process was successful. You may need to reset the Wi-Fi adapter and re-clone or manually configure.
• Langsom hastighed:
  • Powerline performance can be affected by the quality of your electrical wiring. Older or complex wiring can reduce speeds.
  • Avoid plugging adapters into outlets on different electrical phases if your home has a multi-phase electrical system.
  • Ensure no high-power appliances (e.g., washing machines, refrigerators) are on the same circuit as the Powerline adapters, as they can cause interference.

Resetting the Adapters

If problems persist, you can reset the adapters to their factory default settings. This will erase all custom configurations, including Wi-Fi settings.

1. With the adapter powered on, use a paperclip or a similar pointed object to press and hold the "Reset" button (usually a small pinhole) for approximately 10 seconds until all LEDs briefly flash.
2. Release the button. The adapter will restart with factory default settings. You will then need to re-pair the adapters and reconfigure Wi-Fi settings.

Specifikationer

Figure 9: Compatibility with Homeplug AV standards.

Garanti og support

For warranty information and technical support, please refer to the official STRONG webwebstedet eller kontakt deres kundeservice. Gem din købskvittering som købsbevis i tilfælde af garantikrav.

• Officiel Webwebsted: www.strong.tv
• Kundesupport: Se supportafsnittet på den officielle webwebsted for kontaktoplysninger, der er specifikke for din region.

Figur 10: Netværkssikkerhedsfunktioner.