Orbit PC-1F fotocelle 500W ledningsmonteret brugsanvisning

Indledning

This manual provides detailed instructions for the installation, operation, and maintenance of your Orbit PC-1F Photo Cell 500W Wire In. This device is designed to automatically control lighting fixtures based on ambient light levels, providing convenience and energy efficiency.

Image: The Orbit PC-1F Photo Cell, a compact black unit with a light sensor lens and three electrical wires (red, white, black) extending from its base.

Sikkerhedsoplysninger

Læs og forstå alle sikkerhedsinstruktioner, før du installerer eller bruger dette produkt. Manglende overholdelse af disse instruktioner kan resultere i elektrisk stød, brand eller andre farer.

Elektrisk fare: Installationen bør kun udføres af en kvalificeret elektriker eller i overensstemmelse med lokale el-forskrifter.
Afbryd strømmen: Always disconnect power at the circuit breaker or fuse box before installing or servicing the photo cell.
Voltage: Sørg for, at voltage supply matches the requirements of the photo cell and connected fixtures.
Wattage: Overskrid ikke det maksimale wattage rating of 500W for connected lighting.
Udendørs brug: This device is designed for outdoor use. Ensure all connections are properly sealed and protected from moisture.

Opsætning og installation

Proper installation is crucial for the optimal performance of the PC-1F Photo Cell.

Vælg placering: Select a mounting location where the photo cell's sensor will be exposed to natural daylight and not obstructed by eaves, trees, or other structures. Avoid locations where artificial light sources (e.g., streetlights, porch lights) might shine directly onto the sensor, as this can cause erratic operation.
Afbryd strømmen: Turn off the power to the circuit at the main electrical panel before beginning installation.
Ledningsforbindelser:
- Tilslut sort ledning from the photo cell to the incoming 120V AC Line (hot) wire.
- Tilslut hvid ledning from the photo cell to the Neutral wire of the power supply and to the Neutral wire of the lighting fixture.
- Tilslut rød ledning from the photo cell to the Load (hot) wire of the lighting fixture.
Ensure all wire connections are secure and insulated with appropriate wire connectors.
Montering: Securely mount the photo cell using appropriate hardware. Ensure the sensor lens faces the direction of natural light.
Gendan strøm: Once all connections are made and secured, restore power at the circuit breaker.

Betjeningsvejledning

The Orbit PC-1F Photo Cell operates automatically once installed and powered.

Automatisk drift: The photo cell is designed to detect ambient light levels. When natural light diminishes below a certain threshold (e.g., at dusk), the photo cell will automatically activate the connected lighting fixtures.
Daylight Deactivation: Conversely, when sufficient natural light returns (e.g., at dawn), the photo cell will automatically deactivate the connected lighting fixtures.
Tidsforsinkelse: The photo cell typically incorporates a short time delay to prevent false triggering from transient light changes (e.g., car headlights, lightning flashes).

Opretholdelse

Minimal maintenance is required for the PC-1F Photo Cell to ensure continued reliable operation.

Sensorrensning: Periodically inspect the photo cell's sensor lens for dirt, dust, or debris. Gently clean the lens with a soft, damp cloth if necessary. Do not use abrasive cleaners.
Tilslutningskontrol: Annually, or if issues arise, inspect the wiring connections to ensure they remain secure and free from corrosion. Ensure power is disconnected before performing any inspection.
Kontrol af obstruktion: Ensure no new obstructions (e.g., growing foliage, new structures) are blocking natural light from reaching the sensor.

Fejlfinding

Problem	Mulig årsag	Løsning
Lights stay on during the day.	Sensoren er blokeret eller snavset. Artificial light source shining on sensor. Ledningsfejl.	Clean sensor lens; remove obstructions. Relocate photo cell or shield sensor from artificial light. Verify wiring connections (refer to Setup section).
Lysene tændes ikke om natten.	No power to the photo cell. Fejlbehæftet ledningsforbindelse. Photo cell failure. Connected light fixture issue.	Check circuit breaker and power supply. Inspicer og fastgør alle ledningsforbindelser. Replace photo cell if other solutions fail. Test connected light fixture independently.
Lights flicker or cycle rapidly.	Sensor exposed to intermittent light. Løs ledningsforbindelse.	Relocate photo cell or shield sensor from intermittent light sources. Kontroller og fastgør alle ledningsforbindelser.

Specifikationer

Model: PC-1F
Mærke: Orbit
Effektværdi: 500 W (maksimum)
Input bindtage: Standard 120V AC (typical for residential/commercial lighting)
Operation: Automatic Dusk-to-Dawn
Ledningsføring: Wire-in type (Black: Line, White: Neutral, Red: Load)
Fabrikant: Orbit Industrier
ASIN: B072B8D69Q
Dato først tilgængelig: 20. marts 2017

Garanti og support

Specific warranty details are not provided in this document. For warranty information, technical support, or replacement parts, please contact Orbit Industries directly or refer to their official webwebsted.

When contacting support, please have your product model number (PC-1F) and purchase date available.

	Installations- og fejlfindingsvejledning til Orbit Automatic Converter (model 57029, 57030) Comprehensive guide for installing and troubleshooting the Orbit Automatic Converter (Models 57029, 57030) for sprinkler systems. Learn how to convert manual valves to automatic, wire the converter, and resolve common issues.
	Orbit 27752-24 Automatisk Vandingssystem Brugermanual Denne manual indeholder instruktioner til Orbit 27752-24 automatisk vandingssystem, der dækker installation, programmering, manuel vanding og fejlfinding.
	Orbit 2 Outlet Advanced Hose Armature Brugermanual og Programmeringsvejledning Omfattende guide til Orbit 2 Outlet Advanced Hose Faucet Timer, med detaljer om installation, programmering af vandingsplaner, manuel betjening, regnforsinkelsesfunktioner, fejlfindingstips og vigtige sikkerhedsadvarsler.
	Instruktioner til Orbit automatisk havevandingssystem Omfattende instruktioner til opsætning og programmering af Orbit Automatic Havevandingssystem (model 27752), inklusive installation, programmering og fejlfinding.
	Orbit Automatisk Havevandingssystem Brugsanvisning Brugsanvisning til Orbit Model 27752 automatisk havevandingssystem, der dækker installation, programmering og fejlfinding for op til 4 stationer.
	Orbit Automatisk Havevandingssystem Brugsanvisning Omfattende instruktionsmanual til Orbit automatisk havevandingssystem (model 62032, 94932, 62732, 91932), der dækker installation, programmering, driftstilstande, vedligeholdelse og fejlfinding.

Orbit PC-1F