APC Back-UPS Pro 1350VA UPS Batteribackup og overspændingsbeskytter BX1350M Brugermanual

Indledning

This manual provides essential instructions for the installation, operation, maintenance, and troubleshooting of your APC Back-UPS Pro 1350VA Uninterruptible Power Supply (UPS). This device is designed to provide battery backup power and surge protection for electronic equipment, ensuring continuous operation during power outages and protection against damaging power fluctuations.

Figure 1: APC Back-UPS Pro 1350VA UPS, angled view.

Pakkens indhold

Bekræft, at din pakke indeholder følgende varer:

• APC Back-UPS Pro 1350VA UPS Unit
• Brugervejledning (dette dokument)
• USB kommunikationskabel
• Koaksial kabel

Opsætning

1. Første batteritilslutning

The UPS is shipped with the battery disconnected for safety during transit. Before initial use, the internal battery must be connected.

1. Place the UPS in its desired location. Ensure adequate ventilation around the unit.
2. Refer to the battery compartment access instructions (typically located on the bottom or rear of the unit) to connect the internal battery.
3. Luk batterirummet forsvarligt.

2. Tilslutning af udstyr

The UPS features two types of outlets: Battery Backup & Surge Protection, and Surge Protection Only.

Figure 2: Rear panel with outlets and communication ports.

• Battery Backup & Surge Protection Outlets (5 outlets): Connect critical equipment such as your computer, monitor, external hard drives, and network router to these outlets. These devices will receive power from the battery during an outage.
• Surge Protection Only Outlets (5 outlets): Tilslut ikke-kritisk udstyr som printere, scannere eller skrivebordscomputereamps to these outlets. These devices are protected from surges but will not receive battery power during an outage.

3. Tilslutning til strømforsyningen

Plug the UPS power cord into a grounded 120V AC wall outlet. Avoid using extension cords or surge protectors with the UPS.

4. Første opladning

Allow the UPS to charge for at least 24 hours before connecting any equipment to ensure maximum battery runtime. The UPS will provide surge protection even if the battery is not fully charged.

5. Beskyttelse af datalinjer

For network dataline protection, connect your network cable from the wall outlet to the 'IN' port on the UPS, and then connect a second network cable from the 'OUT' port to your device (e.g., computer, router). Similarly, use the coaxial cable ports for cable modem or TV protection.

Betjening af UPS'en

Frontpanel display og kontroller

Figure 3: Front panel with LCD display and control buttons.

The front panel features an LCD display and control buttons for monitoring and managing the UPS.

• Power knap: Tænder eller slukker UPS'en.
• Display knap: Cycles through various display screens showing information such as battery charge, estimated runtime, input/output voltage, and load.
• Mute-knap: Dæmper hørbare alarmer.

Automatisk voltage Forordning (AVR)

The UPS is equipped with Automatic Voltage-regulering (AVR) for at korrigere mindre volumentage fluctuations without switching to battery power. This extends battery life by reducing the frequency of battery usage.

PowerChute software

For advanced management and automatic shutdown capabilities, connect the UPS to your computer using the provided USB cable. Download and install the PowerChute software from the APC webwebsted. Denne software giver dig mulighed for at:

• Overvåg UPS-status og strømforhold.
• Configure automatic, graceful shutdown of your computer during extended power outages.
• View energy usage and cost.

For Mac OS, use native "Energy Saver" settings for UPS management.

Opretholdelse

Udskiftning af batteri

The APC Back-UPS Pro 1350VA features a user-replaceable battery (model APCRBC123, sold separately). Batteries typically last 3-5 years depending on usage and environmental conditions. Replace the battery when the UPS indicates a battery fault or when runtime significantly decreases.

1. Turn off all connected equipment and the UPS.
2. Afbryd UPS'en fra stikkontakten.
3. Follow the instructions provided with the replacement battery for safe removal of the old battery and installation of the new one.
4. Genbrug gamle batterier ansvarligt.

Rensning

Rengør regelmæssigt UPS'ens yderside med en blød, tør klud. Brug ikke flydende rengøringsmidler eller opløsningsmidler. Sørg for, at ventilationsåbningerne er fri for støv og snavs.

Fejlfinding

If the UPS is not operating correctly, consult the following table for common issues and solutions.

If problems persist after attempting these solutions, contact APC customer support.

Specifikationer

Garanti og support

For information regarding the manufacturer's warranty, please refer to the documentation included with your product or visit the official APC webwebsted. Udvidede beskyttelsesplaner kan muligvis også købes.

For technical assistance or customer support, please visit the APC by Schneider Electric Store or contact APC customer service directly.