Indledning
This manual provides detailed instructions for the installation, operation, and maintenance of your Planet Audio TR5000.1D Class D Monoblock Car Amplifier. Please read this manual thoroughly before attempting installation or operation to ensure proper use and to prevent damage to the unit or your vehicle.
Sikkerhedsoplysninger
- Frakobl altid bilens negative batteripol, inden du påbegynder nogen form for installation.
- Sørg for, at alle ledninger er korrekt ført og fastgjort for at forhindre skader eller kortslutninger.
- Brug passende ledningsføring til strøm- og jordforbindelser som angivet i denne manual.
- Installer amplifier in a location that allows for adequate ventilation and is protected from moisture and excessive heat.
- Professionel installation anbefales for optimal ydeevne og sikkerhed.
Pakkens indhold
Bekræft at alle varer er til stede i pakken:
- Planet Audio TR5000.1D Monoblock Amplivligere
- Fjernbetjening af subwoofer
- Instruktionsmanual (dette dokument)
- Mounting Hardware (screws, etc. - assumed, not explicitly listed in "whats_in_the_box" but implied for installation)
Produktegenskaber
- Strømudgang: 5000 Watts Max x 1 @ 1 Ohm, 2500 Watts Max x 1 @ 2 Ohms, 1250 Watts Max x 1 @ 4 Ohms. Strapping capable for 10,000 Watts x 1 @ 2 Ohms.
- Klasse D topologi: High efficiency design reduces power loss and heat generation.
- MOSFET strømforsyning: Ensures precise control of output voltage og nuværende.
- 1 Ohm Stabil: Capable of continuously powering 1 Ohm loads, ideal for demanding subwoofers.
- Strapping Capable: Allows two TR5000.1D amplifiers to be linked for double the power output.
- Fasestyring: Adjusts speaker phase to optimize sound alignment with other audio components.
- Variable Subsonic Filter: Protects subwoofers by filtering out frequencies below their safe operating range.
- Fjernbetjening af subwoofer: Provides convenient bass level adjustment from the driver's seat.
- Low Level Inputs: RCA inputs for connecting to head units.
- Variable Gain Control: Adjusts input sensitivity to match the head unit's output.
Komponentidentifikation
Amplifier Overview
Figur 1: Øverst view of the Planet Audio TR5000.1D Monoblock Ampløfter, showcasing its sleek design and illuminated logo.
Control Panel (Front View)
Figure 2: Front panel of the amplifier showing RCA inputs, gain controls, crossover adjustments, and status indicators.
- Strøm/Beskyt LED: Angiver amplifier status. Green for power, Red for protection mode.
- Input Level (Gain) Control: Justerer inputfølsomheden.
- Subsonisk filter: Adjustable filter to remove ultra-low frequencies.
- Bass Boost: Adjustable bass equalization.
- Low Pass Freq (LPF): Adjustable low-pass crossover frequency.
- Fasestyring: Switch to adjust output phase (0° or 180°).
- Amp Mode Switch: Selects Master or Slave mode for strapping.
- Højttalerterminaler: Connects to subwoofers.
- Line Out (RCA): Provides a full-range output for connecting additional amplivførere.
- Indgange (RCA): Connects to the head unit's low-level outputs.
Power Connection Panel (Rear View)
Figure 3: Rear panel of the amplifier showing power, ground, remote, and remote subwoofer level control connections.
- +12V Power Terminal: Connects to the vehicle's positive battery terminal.
- Fjernterminal: Connects to the head unit's remote turn-on lead.
- Jordterminal: Connects to a solid chassis ground point.
- Remote Subwoofer Level Control Port: Connects the wired remote control.
Fjernbetjening af subwoofer niveaukontrol
Figure 4: Wired remote control for adjusting subwoofer output level.
This control allows for convenient adjustment of the subwoofer output level from the driver's seat. Connect it to the "REMOTE SUBWOOFER LEVEL CONTROL" port on the ampliferens bagpanel.
Opsætning og installation
Generelle betragtninger
- Choose a mounting location that is dry, well-ventilated, and secure. Avoid mounting on carpet or in enclosed spaces without airflow.
- Ensure sufficient clearance around the ampvarmebeholder til afkøling.
- Keep power and RCA cables separated to minimize noise interference.
Ledningsforbindelser
Vigtig: Disconnect the vehicle's negative battery terminal before making any power connections.
- Strøm (+12V): Connect a heavy-gauge cable (e.g., 4 AWG or larger for 5000W) from the amplifier's +12V terminal directly to the vehicle's positive battery terminal. Install an in-line fuse holder within 18 inches (45 cm) of the battery. The fuse rating should match the amplifier's requirements (e.g., 200 Amp ANL).
- Jord (GND): Connect a heavy-gauge cable (same as power) from the amplifier's GND terminal to a clean, unpainted metal point on the vehicle's chassis. Ensure a good electrical connection by scraping away any paint or rust.
- Fjernbetjening (REM): Tilslut en ledning med mindre diameter (f.eks. 18 AWG) fra ampFjernbetjeningens REM-terminal til fjernbetjeningens tændingsudgang på din hovedenhed. Denne ledning tænder amptænd og sluk for sprøjten med hovedenheden.
- RCA-indgange: Connect RCA cables from the head unit's low-level outputs to the amplifier's "INPUTS" (L and R).
- Højttaler output: Tilslut din(e) subwoofer(e) til amplifier's "SPEAKER" terminals. Observe correct polarity (+ to + and - to -). Ensure the total impedance of your subwoofer(s) matches the amplifier's stable operating range (1 to 8 Ohm).
- Fjernbetjening af subwooferniveau: Plug the remote control cable into the dedicated port on the amplivligere.
Montering af Amplivligere
Monter sikkert amplifier using appropriate screws. Ensure the mounting surface is strong enough to support the amplifier's weight and that no vehicle wiring or fuel lines are damaged during drilling.
Betjeningsvejledning
Initial Setup and Adjustments
- Gain Control (Input Level):
Start med amplifier's gain control set to minimum (fully counter-clockwise). Turn your head unit volume to about 75% of its maximum. Slowly increase the amplifier's gain control until you hear distortion, then back it off slightly. This matches the ampsenderens indgangsfølsomhed i forhold til din hovedenheds udgang.
- Lavpasfilter (LPF):
Adjust the LPF frequency to filter out high frequencies from reaching your subwoofer. A common starting point is 80-100 Hz. Experiment to blend the subwoofer output seamlessly with your main speakers.
- Subsonisk filter:
Set the subsonic filter to a frequency just below your subwoofer's resonant frequency or port tuning frequency (if ported). This protects the subwoofer from playing frequencies too low for it to reproduce safely, typically around 20-30 Hz.
- Bass Boost:
Use the bass boost sparingly. Excessive bass boost can lead to distortion and potential damage to your subwoofer. Start at minimum and increase only if desired, listening carefully for distortion.
- Fasestyring:
Switch between 0° and 180° to find the setting that provides the most impactful and cohesive bass response with your main speakers. This often involves listening from the driver's seat.
Using the Remote Subwoofer Level Control
Når amplifier's gain is set, the remote subwoofer level control allows you to adjust the subwoofer's output volume independently from the head unit's main volume. This is useful for quick adjustments based on music genre or personal preference.
Fejlfinding
| Problem | Mulig årsag | Løsning |
|---|---|---|
| Ingen strøm (strøm-LED slukket) | Sprunget sikring, dårlig strøm-/jordforbindelse, intet fjerntændingssignal. | Check in-line fuse, verify +12V, GND, and REM connections. |
| Protection Mode (Protect LED On) | Kortslutning i højttalerledninger, for lav impedans, overophedning, DC-offset. | Check speaker wiring for shorts, verify speaker impedance, ensure adequate ventilation, allow ampvarmebeholder til afkøling. |
| Ingen lyd | RCA cables disconnected, gain too low, head unit settings, speaker wires disconnected. | Verify RCA connections, adjust gain, check head unit output, ensure speaker wires are connected. |
| Forvrænget lyd | Gain set too high, bass boost excessive, poor ground connection, damaged speaker. | Reduce gain, lower bass boost, check ground connection, inspect speaker. |
| Motorstøj/Hylen | Poor ground, RCA cables routed near power cables, faulty head unit. | Improve ground connection, re-route RCA cables away from power, consider a ground loop isolator. |
Specifikationer
| Specifikation | Værdi |
|---|---|
| Modelnummer | TR5000.1D |
| Udgangseffekt (maks.) | 5000 watt x 1 @ 1 ohm |
| Udgangseffekt (RMS) | 2500 Watts x 1 @ 2 Ohms, 1250 Watts x 1 @ 4 Ohms |
| Strapped Power (Max) | 10,000 Watts x 1 @ 2 Ohms |
| Højttalerimpedans | 1 til 8 Ohm |
| THD @ RMS Output | 0.01 % |
| S/N-forhold | 105 dB |
| Frekvensrespons | 20 Hz til 250 Hz |
| Sikringsmængde | 1 x 200 Amp ANL |
| Dimensioner (L x B x H) | 18.5 cm x 9.5 cm x 2.13 cm |
| Varens vægt | 13.49 lbs. |
| Voltage | 8 volt (driftsspændingtage rækkevidde) |
| Forbindelsesteknologier | RCA |
Opretholdelse
- Behold ampFjerneren er ren og fri for støv og snavs. Brug en blød, tør klud til rengøring.
- Ensure ventilation openings are not obstructed to prevent overheating.
- Kontrollér regelmæssigt alle ledningsforbindelser for tæthed og korrosion.
- Undgå at udsætte amplifier til ekstreme temperaturer eller fugt.
Garanti og support
Planet Audio provides a 6-year Platinum Online Dealer Warranty for this product when purchased through Amazon.com. For warranty claims or technical support, please refer to the official Planet Audio website or contact their customer service department. Professional installation is strongly encouraged to ensure proper and safe functionality, which may also be a condition for warranty validity.
For yderligere hjælp, besøg Planet Audio Store on Amazon.
