1. Introduktion
This manual provides comprehensive instructions for the installation, operation, and maintenance of your Lutron Lumea 150W Dimmer Switch, model LECL-153PH-WH. This dimmer is designed to control dimmable LED, incandescent, and halogen light sources, offering adjustable light levels for enhanced comfort and energy savings.
2. Vigtige sikkerhedsoplysninger
- ADVARSEL: For at undgå brand, stød eller dødsfald skal du slukke for strømmen ved afbryderen eller sikringsboksen og kontrollere, at strømmen er afbrudt, før du tilslutter ledninger.
- Installer i overensstemmelse med alle nationale og lokale elektriske koder.
- Use only with permanently installed fixtures with dimmable LED, incandescent, or halogen lamps.
- Do not use with non-dimmable light sources, motor-driven appliances, or transformers.
- Hvis du er i tvivl om nogen del af disse instruktioner, skal du kontakte en kvalificeret elektriker.
3. Pakkens indhold
- One (1) Lutron Lumea 150W Dimmer Switch (Model LECL-153PH-WH)
- Note: Wall plate is not included and is sold separately.
4. Installationsvejledning
- Sluk for strømmen: Locate the circuit breaker or fuse box that controls the lighting circuit you will be working on. Turn off the power completely. Verify power is off using a voltage tester.
- Fjern eksisterende switch: Fjern forsigtigt vægpladen, og skru den eksisterende afbryder af vægdåsen. Frakobl ledningerne fra den gamle afbryder.
- Identificér ledninger: Identify the following wires in your wall box: Line (hot), Load (to light fixture), and Ground. If installing in a 3-way application, identify the traveler wires.
- Tilslutning af lysdæmperen: Connect the wires to the Lutron Lumea dimmer switch using the screw terminals. Refer to the wiring diagram below for typical connections. Ensure all connections are secure.
- Monter lysdæmperen: Gently fold the wires into the wall box and secure the dimmer switch to the wall box using the provided screws.
- Installer vægplade: Attach the new wall plate (sold separately) over the dimmer switch.
- Gendan strøm: Tænd for strømmen igen ved afbryderen.
Figure 1: Lutron Lumea Dimmer Switch. Dette billede viser forsiden og siden views of the dimmer switch, highlighting the slider control, the on/off button, and the wiring terminals. Labels such as "POWER", "OFF", "TURN", "UP", "COURANT", "ARRÊTEZ" are visible on the metal frame, along with wattage ratings for incandescent/ballast (600W) and LED (150W).
Wiring Diagram (Typical Single-Pole Installation)
- Grøn ledning: Connect to Ground wire from wall box.
- Sort ledning: Connect to Line (hot) wire from wall box.
- Rød ledning: Connect to Load wire (to light fixture).
- Red/White Stripe Wire (if present): Used for 3-way applications. Cap if not used.
5. Operating Your Dimmer Switch
- Tænd/sluk lys: Press the bottom button to turn the lights on or off.
- Juster lysstyrke: Move the slider control up to increase light brightness and down to decrease light brightness.
6. Pleje og vedligeholdelse
To clean your dimmer switch, wipe with a soft, damp cloth. Do not use chemical cleaners or abrasive materials, as these may damage the finish.
7. Fejlfinding
| Problem | Mulig årsag | Løsning |
|---|---|---|
| Lysene tænder ikke. | Power is off at breaker; loose wiring; bulb burned out. | Check circuit breaker; verify wiring connections; replace bulb. |
| Lysene flimrer eller brummer. | Non-dimmable bulbs; incompatible bulbs; loose wiring. | Ensure bulbs are dimmable; try different dimmable bulbs; check wiring. |
| Lights do not dim properly. | Non-dimmable bulbs; dimmer capacity exceeded; incompatible bulbs. | Use dimmable bulbs; ensure total wattage does not exceed 150W LED or 600W Incandescent/Halogen; try different dimmable bulbs. |
8. Produktspecifikationer
- Model: LECL-153PH-WH
- Mærke: Lutron
- Driftstilstand: TÆND SLUK
- Nuværende vurdering: 1.25 Amps
- Operation Voltage: 120 volt
- Wattage: 150W (LED), 600W (Incandescent/Halogen)
- Kontakttype: Normalt åben
- Connector Type: Clamp
- Terminal: Skrue
- Dimensioner (L x B x H): 2 x 4 x 6 tommer
- Kredittype: Lysdæmper
- Monteringstype: Vægmontering
- Aktuatortype: Skyder
- Kontaktmateriale: Plast
- International beskyttelsesvurdering: IP54
- Kontrolmetode: Røre
- Farve: Hvid
- Varens vægt: 3.52 ounce
- Type pære: LED, Incandescent, Halogen
- Særlige funktioner: Wall plate Not Included (Sold Separately)
9. Garanti og kundesupport
This Lutron product is covered by a warranty. For specific warranty details, please refer to the documentation included with your purchase or visit the official Lutron website. For technical assistance or customer support, please contact Lutron at:
- Telefon: 1-800-523-9466
- Webwebsted: www.lutron.com
