APC SMT750I Smart-UPS 750VA LCD 230V 500W Sort Tower UPS Brugermanual

1. Produktet er slutview

The APC Smart-UPS SMT750I is an Uninterruptible Power Supply (UPS) designed to provide reliable power protection for electronic equipment. It safeguards connected devices from power outages, bindtage fluctuations, and surges, ensuring continuous operation and preventing data loss. This model features a 750VA/500W capacity, 230V output, and an intuitive LCD interface for monitoring and control.

Figur 1: Forside view of the APC SMT750I Smart-UPS, showing the LCD display and control buttons.

2. Sikkerhedsoplysninger

Read these instructions carefully before installing, operating, servicing, or maintaining the equipment. Failure to follow these instructions can result in equipment damage, property damage, or minor to severe injury.

• Fare for elektrisk stød: The UPS contains internal batteries and can produce hazardous voltage even when disconnected from the utility power.
• Batterisikkerhed: Batteries are heavy. Always use proper lifting techniques. Do not dispose of batteries in a fire as they may explode. Do not open or mutilate batteries. Released electrolyte is harmful to the skin and eyes.
• Vægt: The unit is heavy. Use caution when lifting and positioning.
• Miljø: Operate the UPS indoors in a controlled environment, away from excessive moisture, heat, or conductive contaminants.

3. Opsætning og installation

3.1 Pakkens indhold

Bekræft, at følgende varer er inkluderet i din pakke:

• APC Smart-UPS SMT750I-enhed
• Dokumentations-cd
• USB kommunikationskabel
• Serielt kommunikationskabel
• Netledninger (regionsspecifikke)

3.2 Placering

Position the UPS in a location that meets the following criteria:

• Væk fra direkte sollys og varmekilder.
• Adequate airflow around the unit. Do not block ventilation openings.
• On a sturdy, level surface.

3.3 Tilslutning af batteriet

The UPS is shipped with the battery disconnected for safety. Follow these steps to connect the internal battery:

1. Remove the front bezel of the UPS.
2. Connect the battery cables as indicated in the battery compartment. Ensure a secure connection.
3. Udskift frontpanelet.

3.4 Connecting Equipment and Power

1. Plug the UPS power cord into a grounded 230V AC outlet.
2. Connect your computer, monitor, and other critical equipment to the UPS outlets. Ensure that the total load does not exceed the UPS capacity (500W).
3. For network management, connect the USB or Serial cable from the UPS to your computer.

4. Betjening

4.1 Tænd/sluk

• For at tænde: Tryk på tænd/sluk-knappen på frontpanelet. LCD-skærmen lyser, og UPS'en udfører en selvtest.
• For at slukke: Tryk på tænd/sluk-knappen, og hold den nede, indtil UPS'en slukker.

4.2 LCD-skærm og navigation

The LCD display provides real-time information about the UPS status, battery charge, load, and various settings. Use the navigation buttons (up, down, enter, escape) to browse menus and adjust settings.

• Statusskærm: Displays current operational status, input/output voltage og batteriniveau.
• Konfigurationsmenu: Tillader justering af indstillinger såsom udgangsvolumentage, sensitivity, and alarm preferences.

4.3 Forståelse af indikatorer

The UPS uses audible alarms and visual indicators on the LCD to communicate its status:

• På batteri: UPS is providing power from its internal battery.
• Overbelaste: Connected equipment exceeds the UPS capacity. Disconnect non-essential devices.
• Lavt batteri: Battery charge is critically low. Save work and shut down connected equipment.
• Fejl: An internal error has occurred. Refer to the troubleshooting section.

5. Vedligeholdelse

5.1 Batteripleje og udskiftning

The UPS uses a sealed lead-acid battery. The typical battery life is 3-5 years, depending on usage and environmental conditions. Replace the battery when the UPS indicates a "Battery Fault" or "Replace Battery" message.

1. Order a genuine APC replacement battery cartridge (RBC).
2. Power off the UPS and disconnect it from the utility power.
3. Follow the instructions provided with the replacement battery for safe removal and installation.
4. Genbrug gamle batterier ansvarligt.

5.2 Rengøring

Rengør UPS'ens yderside regelmæssigt med en blød, tør klud. Brug ikke flydende rengøringsmidler eller rengøringsmidler på aerosolbasis. Sørg for, at ventilationsåbningerne er fri for støv og snavs.

6. Fejlfinding

This section provides solutions to common issues you may encounter with your UPS.

7. Specifikationer

8. Garanti og support

8.1 Garantioplysninger

APC warrants its products to be free from defects in materials and workmanship for a period specified in the warranty statement included with your purchase. The warranty period typically covers the UPS unit and internal batteries. Please retain your proof of purchase for warranty claims.

8.2 Teknisk support

For technical assistance, troubleshooting beyond this manual, or warranty inquiries, please contact APC customer support. Visit the official APC webwebsted for kontaktoplysninger, der er specifikke for din region.

Note: Product specifications and warranty terms are subject to change without notice. Refer to the official APC website or included documentation for the most current information.