Indledning
This manual provides essential instructions for the safe installation, operation, and maintenance of your APC Smart-UPS SRT 10KVA Rackmount Uninterruptible Power Supply (UPS) system, model SRT10KRMXLT-5KTF2. This system includes two 208V to 120V 2U 5KVA Step-Down Transformers. Please read this manual thoroughly before installing or operating the equipment.
Vigtige sikkerhedsinstruktioner
Overhold alle advarsler og betjeningsinstruktioner i denne manual. Undladelse af at gøre dette kan medføre personskade eller beskadigelse af udstyret.
- Denne UPS indeholder interne batterier og kan udgøre en risiko for elektrisk stød, selv når den er frakoblet vekselstrømskilden.
- Service af batterier bør udføres eller overvåges af personale, der har kendskab til batterier og de nødvendige forholdsregler.
- Bortskaf ikke batterier i åben ild. Batterierne kan eksplodere.
- Batterier må ikke åbnes eller ødelægges. Frigivet elektrolyt er skadelig for hud og øjne. Det kan være giftigt.
- Et batteri kan udgøre en risiko for elektrisk stød og høj kortslutningsstrøm.
- Refer to local codes for all wiring.
Opsætning og installation
1. Udpakning og inspektion
Carefully unpack the UPS system and its components. Inspect for any shipping damage. Report any damage to the carrier and your dealer. Retain the packaging materials for future use.
2. Fysisk installation
The APC Smart-UPS SRT 10KVA system supports both rack mount and tower configurations. Ensure adequate ventilation around the unit.
- Rack montering: Secure the UPS and step-down transformers into a standard 19-inch equipment rack using the provided mounting hardware. Ensure proper weight distribution.
- Tårn: If installing in a tower configuration, use the supplied tower stands to ensure stability.
Figur 1: APC Smart-UPS SRT 10KVA Rackmount System. This image displays the APC Smart-UPS SRT 10KVA system, configured for rack mounting. It includes the main UPS unit with its front panel display, and additional rack-mountable components, likely battery packs or step-down transformers, all featuring a black mesh design and the APC logo.
3. Elektriske forbindelser
Connect the UPS to a dedicated electrical circuit. Ensure the input voltage matches the UPS requirements (208V nominal). Connect your equipment to the output receptacles of the UPS and the 208V to 120V step-down transformers as needed.
- Indgangseffekt: Connect the UPS input power cord to a properly grounded 208V AC outlet.
- Udgangseffekt: Connect critical equipment to the UPS output receptacles. For 120V loads, connect them to the output receptacles of the 208V to 120V 5KVA Step-Down Transformers.
- Batteriforbindelse: Ensure all internal and external battery connections are secure.
4. Første opstart
After all connections are made, press the power button on the front panel to turn on the UPS. The UPS will perform a self-test and then enter online mode.
Operation
1. Front Panel Display (LCD)
The LCD display provides real-time information about the UPS status, load, battery charge, and various settings. Use the navigation buttons (ESC, OK, Up, Down) to browse menus and adjust settings.
- Statusskærm: Displays current output voltage, belastningsprocenttage, battery status, and operational mode (Online, On Battery, Bypass).
- Konfigurationsmenu: Allows adjustment of settings such as output voltage, alarm thresholds, and network parameters.
2. Grundlæggende betjening
- Tænder: Tryk på tænd/sluk-knappen, og hold den nede, indtil displayet lyser.
- Slukker: Press and hold the power button until the UPS initiates shutdown.
3. Understanding Status Indicators
The UPS uses various indicators (LEDs and LCD messages) to communicate its operational status and any potential issues. Refer to the troubleshooting section for specific error codes.
Opretholdelse
1. Udskiftning af batteri
The UPS batteries are user-replaceable. Replace batteries when indicated by the UPS or after their service life (typically 3-5 years). Use only APC-approved replacement battery cartridges.
- Sikkerhed først: Disconnect the UPS from AC power and turn it off before attempting battery replacement.
- Procedure: Follow the specific instructions provided with the replacement battery cartridge for safe removal and installation.
2. Rensning
Keep the ventilation openings clear of dust and debris to ensure proper airflow. Use a dry cloth to clean the exterior of the UPS.
Fejlfinding
Dette afsnit indeholder løsninger på almindelige problemer. Kontakt APC's tekniske support ved mere komplekse problemer.
| Problem | Mulig årsag | Løsning |
|---|---|---|
| UPS'en tænder ikke | No input power; discharged battery | Check AC input connection; allow battery to charge for several hours. |
| UPS'en bipper konstant | On battery mode; overload condition | Check AC input; reduce connected load. |
| Battery indicator shows low charge | Battery needs charging or replacement | Allow UPS to charge; perform a battery self-test; replace battery if necessary. |
Specifikationer
- Mærke: APC
- Model: SRT10KRMXLT-5KTF2
- Produktdimensioner: 1 x 1 x 1 tommer
- Varens vægt: 2 pund
- Materiale: Metal
- Kompatible enheder: Server
- Monteringstype: Rack mount, Tower
- Dato først tilgængelig: 23. januar 2017
Garanti og support
APC products are backed by a limited warranty. For detailed warranty information, please refer to the documentation included with your product or visit the official APC website. For technical assistance, troubleshooting, or to inquire about replacement parts, please contact APC customer support.
Online ressourcer: www.apc.com
