1. Introduktion
The KSE-LIGHTS KS-8810 is a robust, handheld LED lamp designed for use in potentially explosive atmospheres. It is an essential tool for professionals in fire and rescue services, industrial settings, and other specialized applications where safety and reliable illumination are paramount. This manual provides detailed instructions for the safe and effective use, maintenance, and troubleshooting of your KS-8810 lamp.
Figur 1.1: The KSE-LIGHTS KS-8810 LED Lamp. This image shows the yellow body of the flashlight with the KSE-LIGHTS logo, black rubberized head, and the clear lens of the LED light source.
2. Sikkerhedsoplysninger
ADVARSEL: Læs alle sikkerhedsadvarsler og instruktioner, før du bruger dette produkt. Manglende overholdelse af advarsler og instruktioner kan resultere i elektrisk stød, brand og/eller alvorlig personskade.
- ATEX-certificering: Denne lamp is ATEX certified for Zone 0 (II 1G Ex ia IIC T4 & Ex ia IIC T4 Ga), meaning it is approved for use in areas where explosive gas atmospheres are present continuously or for long periods. Always ensure the lamp's certification matches the requirements of your operating environment.
- Batterisikkerhed: Use only specified AA alkaline batteries. Do not mix old and new batteries, or different types of batteries. Do not expose batteries to excessive heat or fire. Do not short-circuit batteries.
- Miljøforhold: Lamp is IP68 rated and waterproof up to 3 meters. However, avoid prolonged submersion beyond specified limits. Do not operate the lamp if it appears damaged.
- Opretholdelse: Any maintenance or repair should only be performed by qualified personnel. Unauthorized modifications can compromise safety and void the ATEX certification.
3. Pakkens indhold
Bekræft at alle varer er til stede i pakken:
- 1 x KSE-LIGHTS KS-8810 Handheld Lamp
- 1 x Brugermanual (dette dokument)
Batterier er ikke inkluderet og skal købes separat.
4. Opsætning
4.1 Batteriinstallation
- Sørg for at lamp er slukket.
- Unscrew the rear cap of the lamp ved at dreje den mod uret.
- Insert four (4) AA alkaline batteries into the battery compartment, observing the correct polarity (+/-) as indicated inside the compartment.
- Carefully screw the rear cap back on clockwise until it is securely tightened. Ensure the O-ring seal is properly seated to maintain the lamp's waterproof integrity.
Figur 4.1: Proper grip for handling the KSE-LIGHTS KS-8810 LED Lamp. This image shows a hand, possibly gloved and soiled, firmly grasping the yellow body of the flashlight, demonstrating its ergonomic design for practical use.
5. Betjeningsvejledning
The KS-8810 features a wear-free magnetic on/off switch and offers three distinct light modes.
5.1 Turning On/Off and Changing Modes
- At tænde: Press the magnetic switch located on the side of the lamp. Den lamp will activate in the default Strong Light mode.
- For at ændre lystilstande: Briefly press the magnetic switch again to cycle through the available modes: Strong Light > Work Light > Flashing Light.
- At slukke: Press the magnetic switch once more after cycling through all modes, or hold the switch for approximately 2 seconds from any mode.
The precision lens ensures ideal and homogeneous light distribution across all modes.
6. Vedligeholdelse
6.1 Rengøring
Tør lamp's exterior with a damp cloth. Do not use abrasive cleaners or solvents, as these may damage the housing or seals. Ensure the lens is clean for optimal light output.
6.2 Udskiftning af batteri
Replace all four AA batteries simultaneously when the light output diminishes significantly. Refer to Section 4.1 for battery installation instructions. Always dispose of used batteries according to local regulations.
6.3 Opbevaring
Hvis lamp will not be used for an extended period, remove the batteries to prevent leakage and corrosion. Store the lamp på et køligt, tørt sted væk fra direkte sollys og ekstreme temperaturer.
7. Fejlfinding
| Problem | Mulig årsag | Løsning |
|---|---|---|
| Lamp tændes ikke. | Døde eller forkert installerede batterier. | Udskift batterierne, og sørg for korrekt polaritet. |
| Lysudgangen er svag. | Lav batteristrøm. | Udskift batterierne. |
| Lamp flimrer. | Løs batteriforbindelse eller lav batteristrøm. | Check battery installation; replace batteries if necessary. Ensure end cap is tightly secured. |
| Vand inde i lamp. | Improperly sealed end cap or damaged O-ring. | Immediately remove batteries. Dry the interior thoroughly. Check O-ring for damage and proper seating. If damage persists, contact support. |
If the problem persists after attempting these solutions, please contact KSE-LIGHTS customer support.
8. Specifikationer
| Modelnummer | KS-8810 |
| Mærke | KSE-LYS |
| Dimensioner (L x B x H) | 20 x 7 x 6 cm |
| Vægt | 140 gram |
| Strømkilde | Battery Powered (4 x AA Alkaline batteries, not included) |
| Voltage | 6 volt |
| Pære type | LED |
| Lysstrøm | Up to 180 lumens (Strong Light mode) |
| Køretid | Op til 30 timer |
| Materiale | Aluminium |
| Farve | Gul |
| Beskyttelsesvurdering | IP68 (Waterproof up to 3 meters) |
| ATEX certificering | II 1G Ex ia IIC T4 & Ex ia IIC T4 Ga (Zone 0) |
9. Garanti og support
Information regarding the product warranty and specific customer support contact details is not provided within this manual. For warranty claims or technical assistance, please refer to the product packaging, the point of purchase, or the official KSE-LIGHTS webwebsted.
