1. Introduktion
This manual provides detailed instructions for the installation, operation, and maintenance of your Mount-It! MI-2752 Dual Monitor Mount. Please read these instructions carefully before installation to ensure proper setup and safe use. Retain this manual for future reference.
2. Sikkerhedsoplysninger
ADVARSEL: Failure to read and follow all instructions may result in personal injury or property damage. Ensure all mounting surfaces are capable of holding the weight of your mount and monitors. Do not exceed the maximum listed weight capacity.
- Verify that the mounting surface can support the combined weight of the mount and monitors.
- Do not overtighten screws. Overtightening may cause damage to the product or mounting surface.
- Hold små dele væk fra børn.
- If you have any questions or require assistance, contact customer support.
3. Pakkens indhold
Kontroller, at alle komponenter er til stede og ubeskadigede, før du fortsætter med installationen.
- LCD Monitor Pole with Double-Link Swing Arm
- C-Clamp and Grommet Combo Mechanism
- Cable Management Clips and Trim Caps
- Monitor Mounting Screws (various sizes for VESA 75x75mm and 100x100mm)
- Installation Hardware with Instructions and Hex Tool
4. Specifikationer
| Feature | Specifikation |
|---|---|
| Modelnummer | MI-2752 |
| Kompatibilitet mellem skærmstørrelser | 17-27 inches (per screen) |
| Vægt kapacitet | Up to 22 lbs (per screen) |
| VESA-kompatibilitet | 75x75mm, 100x100mm |
| Monteringsmuligheder | C-Clamp (desks up to 4 inches thick), Grommet Base (desks up to 3.25 inches thick) |
| Tilt justering | -45 til + 45 grader |
| Justering af drejning | 180 grader |
| Rotation | 360 grader (portræt/landskab) |
| Højdejustering | Arm assembly adjustable on pole; 1-inch fine adjustment per monitor head |
| Materiale | Legeret stål |
| Farve | Sort |
| Center Post Height | 17.7 tommer |
| Mounting Bracket Span | 28.9 inches (on center) |
5. Installationsvejledning
Follow these steps for proper assembly and installation of your dual monitor mount.
5.1. Attaching the Base to the Pole
- Connect the base (E) to the pole (F) using the provided bolt (I) through the center hole. Tighten until secure.
- Insert the bolt (J) into the remaining hole on the base and tighten.
5.2. Assembling the Clamp
Klamp can be configured for different desk thicknesses.
- For desks 0.4"-1.8" thick: Fastgør Clamp L-Bracket (D) to the Pole Base as shown using two bolts (K). Partially install the two bolts (K) leaving a gap of approximately 0.2 inches (5mm) between the bracket and the base of the screw.
- For desks 1.8"-3.3" thick: Remove the hand knob and flip the bracket so it faces away from the handle, then reinstall the hand knob.
5.3. Fastgørelse af Clamp til skrivebordet
Position the mount on the edge of your desk. Tighten the hand knob until the clamp er forsvarligt fastgjort til skrivebordet.
5.4. Grommet Mounting Option
If your desk has a grommet hole (0.4"-2.4" wide, 0.4"-1.6" thick), you can use the grommet option. Remove the clamp handle and slide the oval plate directly over the grommet bolt. From underneath the desk, slot the grommet handle through the hole and attach the pole on top. Tighten the handle until secure.
5.5. Attaching the Arms to the Pole
- Slide the monitor arms onto the pole.
- Attach the cable clips to the monitor arms and the vertical pole below.
- Adjust the monitor arms to the desired height and tighten the rear bolt using the hex wrench until secure.
5.6. Attaching VESA Plates to Monitors
- Choose the correct mounting bolts and washers for your monitor.
- Attach the VESA plate to the back of the monitor using the selected bolts. Tighten until secure, but do not overtighten.
5.7. Attaching Monitors to Arms
- Slide the VESA plates (with monitors attached) onto the ends of the monitor arms.
- Place the knob onto the height adjustment peg and secure it with the bolt. This allows for fine height adjustments. Do not overtighten.
5.8. Visuel installationsvejledning
6. Betjening og justeringer
The MI-2752 mount offers extensive adjustability to achieve an ergonomic setup.
6.1. Monitor Height Adjustment
The arm assembly height can be adjusted on the pole. Additionally, each monitor head has a 1-inch fine height adjustment. To level the height of the screens, turn the thumb knob on the VESA plate to raise or lower the monitor.
6.2. Vipning, drejning og rotation
The monitor arms allow for:
- Vip: -45 til + 45 grader
- Drejelig: 180 grader
- Rotation: 360 degrees (allowing for portrait or landscape orientation)
Adjust your monitors to the most comfortable viewing position to reduce neck, back, and eye strain.
7. Kabelforvaltning
Integrated cable management clips are provided to keep your desk neat and organized. Route your monitor cables through these clips along the arms and down the pole.
8. Vedligeholdelse
Regelmæssig vedligeholdelse sikrer din skærmbeslags levetid og sikker drift.
- Kontrollér regelmæssigt alle skruer og bolte for at sikre, at de er stramme. Efterspænd efter behov.
- Rengør holderen med en blød kludamp klæde. Undgå slibende rengøringsmidler.
- Store the hex wrenches in the built-in slots on the cable clip for easy access when adjustments are needed.
9. Fejlfinding
If you encounter any issues with your monitor mount, refer to the following common solutions:
- Monitor tilts too easily or won't stay in place: Tighten the bolt behind the VESA bracket.
- Skærme er ikke i vater: Use the 1-inch fine height adjustment on each monitor head by turning the thumb knob on the VESA plate.
- Mount føles ustabil: Sørg for C-clamp or grommet base is securely tightened to the desk. Check all connection points for tightness.
10. Garanti og support
Your Mount-It! Dual Monitor Arm comes with a 5 ÅRS GARANTI.
For any questions or assistance, please contact Mount-It! customer support during normal business hours.
- E-mail: support@mount-it.com
- Telefon: (855) 925-5668
- Webwebsted: www.mount-it.com
