1. Produktet er slutview
The Steinbach Classic 250N Filtration System is a high-performance sand filter designed to maintain clean and clear water in above-ground pools. This powerful unit is suitable for pools with a capacity of up to 19,000 liters, ensuring efficient removal of impurities. It features a robust pump and a versatile 7-way valve for various operational modes.
2. Sikkerhedsoplysninger
Læs alle sikkerhedsinstruktioner omhyggeligt inden installation og betjening for at forhindre personskade eller beskadigelse. Gem denne manual til senere brug.
- Always disconnect the power supply before performing any maintenance or cleaning on the filter system.
- Ensure the electrical outlet is protected by a Ground Fault Circuit Interrupter (GFCI) for safety.
- Brug ikke pumpen, hvis vandtemperaturen overstiger 35 °C (95 °F).
- Hold børn væk fra filtersystemet under drift.
- Ensure all connections are secure and leak-free to prevent water damage or electrical hazards.
- The pump is not self-priming; ensure it is filled with water before starting.
3. Opsætning og installation
Proper installation is crucial for the optimal performance of your filtration system. Follow these steps carefully:
3.1 Udpakning og komponentkontrol
Kontroller, at alle komponenter er til stede og ubeskadigede:
- Filter Tank (250 mm diameter)
- Pump Unit (230V / 200W)
- 7-Way Multi-Port Valve with Pressure Gauge
- Connecting Hoses (32/38 mm diameter)
- Bundplade
- Clamps and Fittings
3.2 Filter Media Preparation
The system requires approximately 10 kg of filter sand with a granule size of 0.7 - 1.2 mm, or compatible filter balls. Refer to the specific instructions for filling the filter tank with your chosen media.
3.3 Montering og tilslutning
- Place the base plate on a firm, level surface near your pool.
- Mount the filter tank and pump securely onto the base plate.
- Connect the pump to the filter tank and the multi-port valve using the provided hoses and fittings. Ensure all connections are tight to prevent leaks.
- Connect the system to your pool's skimmer and return lines using 32/38 mm hoses.
3.4 Optimal placering
For gravity-fed operation, the water level in the pool should be above the sand filter. Avoid situations where the water level is below the filter, as this can hinder proper flow and operation.
4. Betjeningsvejledning
The 7-way multi-port valve allows for different operational modes. Always turn off the pump before changing the valve position.
- FILTER: This is the standard operating mode for daily filtration. Water is pumped through the filter media, and clean water is returned to the pool.
- TILBAGESKYLNING: Used to clean the filter media. Water flows in reverse through the filter, dislodging trapped debris, which is then discharged to waste. Perform when pressure gauge indicates high pressure.
- SKYLLE: Used after backwashing to flush out any remaining debris from the filter media and lines before returning to FILTER mode. Water is discharged to waste.
- WASTE (EMPTY): Bypasses the filter and pumps water directly out of the pool to waste. Useful for lowering pool water level or vacuuming heavy debris directly to waste.
- RECIRCULATE (CIRCULATE): Bypasses the filter and circulates water directly back to the pool. Useful for distributing chemicals without filtering.
- LUKKET: Closes all flow to the filter. Use only when the pump is off and for maintenance tasks that require isolating the filter.
To start operation, ensure the valve is set to FILTER, then turn on the pump. Monitor the pressure gauge for normal operating pressure.
5. Vedligeholdelse
Regular maintenance ensures the longevity and efficiency of your Steinbach filtration system.
5.1 Bagskylning og skylning
Perform backwashing when the pressure gauge reading is 0.2-0.3 bar (3-5 psi) above the clean filter pressure, or when water flow to the pool decreases significantly. Follow with a rinse cycle.
- Sluk for pumpen.
- Indstil ventilen til BACKWASH.
- Turn on the pump and backwash until the water in the sight glass (if present) runs clear (typically 2-3 minutes).
- Sluk for pumpen.
- Indstil ventilen til SKYL.
- Tænd pumpen og skyl i 30-60 sekunder.
- Sluk for pumpen.
- Set the valve back to FILTER.
- Turn on the pump to resume normal filtration.
5.2 Filter Media Replacement
Filter sand typically needs replacement every 3-5 years, depending on usage and water quality. Filter balls may require periodic cleaning or replacement as per their specific instructions.
5.3 Vinterisering
Before freezing temperatures, drain all water from the pump, filter tank, and hoses. Store the pump and valve in a dry, frost-free location. Cover the filter tank if it remains outdoors.
6. Fejlfinding
Se dette afsnit for almindelige problemer og deres mulige løsninger.
| Problem | Mulig årsag | Løsning |
|---|---|---|
| Lav vandgennemstrømning / Dårlig filtrering | Clogged filter media; Clogged skimmer/pump basket; Air in system; Incorrect valve setting. | Perform backwash/rinse; Clean skimmer/pump basket; Bleed air from system; Set valve to FILTER. |
| Høj trykmåleraflæsning | Beskidte filtermedier. | Udfør tilbageskylnings- og skylningscyklus. |
| Water leaking from valve/connections | Loose connections; Damaged O-rings/gaskets. | Tighten connections; Inspect and replace O-rings/gaskets if necessary. |
| Pumpen spæder ikke | Pump not filled with water; Air leak on suction side; Clogged impeller. | Fill pump with water; Check all suction side connections for leaks; Inspect and clear impeller. |
7. Tekniske specifikationer
| Feature | Specifikation |
|---|---|
| Modelnummer | 040385 |
| Mærke | Steinbach |
| Max poolvolumen | Op til 19,000 liter |
| Cirkulationskapacitet | 4,170 liter/time |
| Pumpekapacitet | 6,000 liters/hour (non-self-priming) |
| Voltage | 230 V |
| Magt | 200 W |
| Maks. Vandtemperatur | 35 °C |
| Boiler Diameter | 250 mm |
| Tilslutningsdiameter | 32/38 mm |
| Recommended Sand Quantity | Ca. 10 kg |
| Recommended Granule Size | 0.7 - 1.2 mm |
| Produktmål (L x B x H) | 43 x 27 x 58 cm |
| Produktets vægt | 8.5 kg |
8. Garanti og support
For specific warranty details and terms, please refer to the documentation provided with your purchase. In general, products purchased through Amazon may be eligible for returns or replacements within 30 days, subject to Amazon's return policy.
For technical support, spare parts, or further assistance, please contact Steinbach customer service. Contact information can typically be found on the manufacturer's webwebstedet eller på produktemballagen.
