Simplex 4099-9004 Enkeltvirkende adresserbar manuel trækstation brugermanual

1. Introduktion

This manual provides essential information for the proper installation, operation, and maintenance of the Simplex 4099-9004 Single Action Addressable Manual Pull Station. This device is designed to initiate a fire alarm signal upon manual activation, integrating seamlessly into compatible fire alarm control panels.

The Simplex 4099-9004 is a robust and reliable component of a comprehensive fire detection system, ensuring prompt notification in emergency situations. It features a single-action pull mechanism for straightforward activation.

2. Sikkerhedsoplysninger

ADVARSEL: Installation and servicing of this device must be performed by qualified personnel only, in accordance with all local and national electrical codes, fire codes, and the manufacturer's instructions. Failure to do so may result in property damage, serious injury, or death.

Always disconnect power to the fire alarm control panel before installing, servicing, or removing the pull station.
Ensure all wiring connections are secure and comply with wiring diagrams.
Do not paint over the pull station or obstruct its operation in any way.
Regular testing is crucial to ensure proper functionality.
This device is not intended for outdoor use unless specifically rated for such environments.

3. Opsætning og installation

The Simplex 4099-9004 pull station is designed for indoor surface or flush mounting. Proper installation is critical for reliable operation.

3.1 Udpakning og inspektion

Upon receiving the product, carefully inspect the packaging and the device for any signs of damage. The product packaging includes key identification information such as the Product ID (PID), Description, Part Number, and Serial Number.

Simplex 4099-9004 Pull Station product box with label showing PID, description, part number, and serial number.

Figure 1: Packaging for the Simplex 4099-9004 Pull Station, displaying product identification details including PID: 4099-9004, Description: STATION-LED, SA ADDR, Part No. 06501205, and Serial No. 0650120516047/997.

3.2 Montering

Mount the pull station at the height specified by local codes (typically 42-48 inches from the floor to the operating handle). Ensure the mounting surface is flat and secure. Use appropriate screws and anchors for the wall material.

3.3 Ledningsføring

Connect the pull station to the fire alarm control panel's Signaling Line Circuit (SLC) using appropriate gauge wire as specified by the system's design and local codes. The 4099-9004 is an addressable device, meaning it communicates digitally with the control panel. Refer to the specific wiring diagram provided with your fire alarm control panel for detailed connection instructions. Ensure proper polarity and secure all connections within the terminal block.

4. Betjeningsvejledning

The Simplex 4099-9004 is a single-action pull station. To activate the fire alarm:

Locate the manual pull station.
Firmly grasp the handle and pull it down.
The handle will latch in the down position, indicating activation.
The pull station will send a signal to the fire alarm control panel, initiating the alarm sequence (e.g., sounding horns, flashing strobes, notifying monitoring station).

To reset the pull station after activation, insert the appropriate key into the keyhole and turn it to release the handle. The handle will return to its original position. Remove the key.

Video 1: A demonstration of the Simplex 4099-9004 pull station, showcasing its design and how it appears from various angles. This video provides a visual overview of the product's physical characteristics.

5. Vedligeholdelse

Regular maintenance ensures the longevity and reliability of your Simplex 4099-9004 pull station.

5.1 Rutinemæssig rengøring

Clean the exterior of the pull station periodically with a soft, damp klud. Brug ikke slibende rengøringsmidler eller opløsningsmidler, da disse kan beskadige overfladen eller de indvendige komponenter.

5.2 Funktionstest

Functional testing should be performed regularly as required by local fire codes and NFPA standards (e.g., annually, semi-annually). During testing, activate the pull station to ensure it sends an alarm signal to the control panel. Reset the device after testing. All tests should be conducted by trained and authorized personnel.

6. Fejlfinding

This section addresses common issues you might encounter with the Simplex 4099-9004 pull station. For complex issues, contact a qualified fire alarm technician.

Problem	Mulig årsag	Løsning
Trækstationen aktiverer ikke alarmen.	Forkert ledningsføring. Defekt enhed. Control panel issue.	Verify wiring connections and polarity. Test the device with a multimeter (if qualified). Check control panel status and error logs.
Trækstationen kan ikke nulstilles.	Incorrect key used. Internal mechanism jammed.	Ensure the correct reset key is used. Do not force the mechanism; contact a technician for repair or replacement.
False alarms from pull station.	Physical damage or tampering. Environmental factors (e.g., excessive vibration). Wiring issues (e.g., short circuit).	Undersøg for skader. Ensure stable mounting. Check wiring for shorts or loose connections.

7. Specifikationer

Attribut	Detalje
Mærke	Simplex
Modelnummer	4099-9004
Varenummer	4099-9004
Beskrivelse	Single Action Addressable Manual Pull Station
Strømkilde	Manual (System Powered)
Farve	Rød
Alarmtype	Audible (via connected system)
Varens vægt	13.7 ounce
Produktdimensioner	6 x 5 x 4 tommer
UPC	647358696167

8. Garanti og support

For warranty information and technical support regarding your Simplex 4099-9004 Pull Station, please contact Simplex customer service or your authorized Simplex distributor. Keep your purchase receipt and product serial number handy for any inquiries.

Fabrikant: Simplex Grinnell

For further assistance, refer to the official Simplex webwebstedet eller kontakt deres supportkanaler direkte.

	Simplex IDNet/MAPNET II adresserbare manuelle brandalarmcentraler - Produktdata Detaljeret information om Simplex 4099-seriens adresserbare manuelle brandalarmcentraler, kompatible med IDNet- og MAPNET II-systemer. Funktioner, specifikationer, monteringsmuligheder og produktvalg til forskellige modeller, herunder enkeltvirkende, dobbeltvirkende (glasbrud og tryk) og NO GRIP-muligheder. Overholder ADA-krav og er godkendt af UL, ULC, FM og CSFM.
	Simplex adresserbare manuelle stationer: IDNet/MAPNET II periferiudstyr Udforsk Simplex adresserbare manuelle brandalarmcentraler, med detaljerede oplysninger om deres funktioner, enkelt-/dobbeltvirkende typer, NO GRIP-muligheder og kompatibilitet med IDNet/MAPNET II-systemer. Inkluderer monterings- og specifikationsoplysninger.
	Datablad for Simplex 2099-seriens enkelt- og dobbeltvirkende manuelle brandalarmcentraler Datablad for Simplex 2099-seriens ikke-kodede, ikke-adresserbare manuelle brandalarmcentraler. Dækker funktioner, driftstyper, applikationsreferencer, produktvalg, monteringsmuligheder og specifikationer.
	Datablad for Simplex 4007ES branddetekterings- og kontrolenhed Detaljeret datablad for Simplex 4007ES branddetekterings- og kontrolenheden, der dækker dens MX Digital Addressable Initiation og Addressable Notification-funktioner, funktioner, specifikationer og installationsdetaljer.
	Simplex 4010ES: System for commande d'extinction automatique pour gicleurs Vejledningsteknik Simplex 4010ES detaljering af kommandomoduler for automatiske systemer til udryddelse af gicleurer, couvrant les modes déluge og préventif, med specifikationer, homologationer og câblage skemaer.
	Simplex 4090-9007 IDNet Signal IAM: Adresserbart modul til brandalarmsystemer Detaljerede tekniske specifikationer og funktioner for Simplex 4090-9007 IDNet Signal Individual Addressable Module (IAM), designet til forbedret selektiv signalering og lydstyring i Simplex 4100ES, 4010ES, 4100U og 4008-serien af brandalarmcentraler. Indeholder oplysninger om ledningsføring, betjening og montering.