SafeWaze FS99281-E Faldsikringssele Brugermanual

1. Introduktion

This manual provides essential instructions for the proper use, inspection, and maintenance of the SafeWaze FS99281-E Fall Protection Harness. This harness is designed to be a component of a personal fall arrest system or a work positioning system. It is crucial to read and understand all instructions before using this equipment. Failure to follow these instructions can result in serious injury or death.

The SafeWaze FS99281-E is a durable and lightweight harness featuring a dorsal D-ring for fall arrest and two side D-rings for work positioning. It includes pass-through leg straps and a chest buckle for easy donning and adjustment, suitable for a universal S-XL size range.

2. Sikkerhedsoplysninger

• Uddannelse: Users must be trained by a competent person in the proper use of fall protection equipment, including this harness, and in the recognition of hazards.
• Inspektion: Always inspect the harness before each use. Do not use if any damage or defects are found.
• Kompatibilitet: Ensure all components of your fall protection system (harness, lanyard, anchor point) are compatible and meet applicable standards.
• Vægt kapacitet: This harness has a maximum weight capacity of 310 lbs (140 kg), including clothing, tools, and any other equipment carried by the user.
• Klarering: Ensure adequate fall clearance is maintained below the work surface to prevent striking a lower level or obstruction in the event of a fall.
• Medicinske tilstande: Consult a physician if you have any medical conditions that could affect your ability to safely use fall protection equipment.
• Forskrifter: Always comply with all applicable local, state, and federal regulations (e.g., OSHA, ANSI) regarding fall protection.

3. komponenter

The SafeWaze FS99281-E harness consists of the following key components:

• WebBing: High-strength polyester webbing forms the main structure of the harness.
• Dorsal D-ring: Located on the back, this D-ring is the primary attachment point for a fall arrest lanyard.
• Side D-ringe: Two D-rings located on the sides of the waist belt, used for work positioning.
• Pass-Through Buckles: Used on the chest and leg straps for quick and secure fastening.
• Adjustment Buckles: Spring-loaded buckles for adjusting shoulder, chest, and leg straps to achieve a proper fit.
• Lanyard Keepers: Loops on the shoulder straps to hold unused lanyard legs.
• Fall Arrest Indicators: Stitching designed to tear or show visible damage if the harness has been subjected to a fall arrest event.

Figur 1: The SafeWaze FS99281-E Fall Protection Harness displayed on a mannequin. The image shows the orange polyester webbing, the dorsal D-ring on the back (not fully visible from this angle), the two side D-rings on the waist, and the pass-through buckles on the chest and leg straps. The harness is designed for universal fit and features black adjustment straps and SafeWaze branding.

4. Setup and Donning Instructions

Follow these steps to properly don the SafeWaze FS99281-E harness:

1. Inspicer selen: Before each use, hold the harness by the dorsal D-ring and shake it to allow all straps to fall into place. Inspect all webbing, D-rings, buckles, and stitching for cuts, fraying, deformation, corrosion, or any other damage. Check fall arrest indicators for activation. If any damage is found, remove the harness from service immediately.
2. Orient the Harness: Ensure the dorsal D-ring is positioned at the top of the back. The shoulder straps should be free of twists.
3. Don skulderstropper: Slip the shoulder straps over your shoulders as if putting on a vest. The dorsal D-ring should rest between your shoulder blades.
4. Tilslut benstropper: Bring the leg straps between your legs and connect them to the corresponding buckles on the waist belt. Ensure the straps are not twisted.
5. Tilslut brystremmen: Fasten the chest strap across your chest using the pass-through buckle. Position it approximately 6-8 inches (15-20 cm) below the top of your shoulders.

5. Justering

Proper adjustment is critical for comfort and safety. Adjust all straps until the harness fits snugly but allows for full range of motion.

• Benstropper: Adjust the leg straps so they are snug around your upper thighs. You should be able to slide your flat hand under the strap, but not your clenched fist.
• Skulderstropper: Adjust the shoulder straps to ensure the dorsal D-ring is positioned between your shoulder blades and the harness webbing is taut.
• Brystrem: Adjust the chest strap to keep the shoulder straps properly positioned and prevent them from slipping off. It should be snug but not restrictive.
• Waist Belt (if applicable): Ensure the waist belt is snug around your waist, providing support for the side D-rings if used for work positioning.
• Overskud WebBing: Secure any excess webbing through the keepers to prevent snagging.

6. Driftsprincipper

6.1. Fall Arrest System

When used as part of a personal fall arrest system, the dorsal D-ring is the designated attachment point for a fall arrest lanyard or self-retracting lifeline. The system must include an anchor point capable of supporting 5,000 lbs (22.2 kN) per worker, a full-body harness, and a connecting device (lanyard with energy absorber or SRL).

• Vedhæftet fil: Connect the fall arrest lanyard or SRL only to the dorsal D-ring.
• Ankerpunkt: The anchor point should be located directly above the worker whenever possible to minimize swing fall hazards.
• Post-Fall: If a fall occurs, immediately remove the harness from service and have it inspected by a competent person. Do not reuse a harness that has arrested a fall.

6.2. Work Positioning System

The two side D-rings are designed for work positioning, allowing a worker to be supported at a work location and work with both hands free. A work positioning system is not a fall arrest system and must always be used in conjunction with a separate personal fall arrest system.

• Vedhæftet fil: Connect a work positioning lanyard to both side D-rings.
• Støtte: The work positioning system should limit a free fall to no more than 2 feet (0.6 meters).
• Fall Arrest Backup: Always ensure a separate, independent fall arrest system is in place and properly connected when using the harness for work positioning.

7. Eftersyn og vedligeholdelse

7.1. Inspektion før brug

Perform a thorough visual inspection before each use. Check for:

• WebBing: Cuts, fraying, burns, chemical damage, discoloration, excessive wear, or broken fibers.
• Syning: Loose, broken, or pulled stitches.
• D-ringe: Cracks, deformation, corrosion, sharp edges, or excessive wear.
• Spænder: Proper function, deformation, corrosion, sharp edges, or damage to springs (if applicable). Ensure they engage securely.
• Fall Arrest Indicators: Any signs of activation (e.g., torn stitching).
• Etiketter: Sørg for, at alle etiketter er til stede og læselige.

7.2. Periodisk eftersyn

In addition to pre-use inspections, a competent person must perform a detailed inspection of the harness at least every six months, or more frequently depending on use and environmental conditions. Maintain inspection records.

7.3. Rensning

Clean the harness as needed to remove dirt, grease, or other contaminants.

• Metode: Hand wash only. Use a mild soap or detergent and warm water (max 100°F / 38°C).
• Skylning: Skyl grundigt med rent vand.
• Tørring: Hang to air dry in a clean, shaded area away from direct sunlight, heat, or open flames. Do not machine wash or tumble dry.

7.4. Retirement Criteria

The harness must be immediately removed from service and destroyed if:

• It has been subjected to a fall arrest event.
• Inspection reveals any damage, defects, or excessive wear.
• It shows signs of chemical or heat damage.
• Labels are missing or illegible.
• There is any doubt about its safety or integrity.

8. Opbevaring

Store the harness in a cool, dry, clean area, away from direct sunlight, extreme temperatures, corrosive chemicals, and sharp objects. Avoid storing in areas where it could be exposed to moisture or pests.

9. Fejlfinding

If you encounter issues with your harness, consider the following:

• Forkert pasform: Re-read the "Adjustment" section and ensure all straps are snug and correctly positioned.
• Twisted Straps: Remove the harness and re-don it carefully, ensuring no straps are twisted.
• Beskadigede komponenter: If any part of the harness appears damaged or defective during inspection, immediately remove it from service and do not attempt repairs.
• Unsure About Safety: If you have any doubts about the harness's condition or proper use, do not use it. Consult a competent person or contact SafeWaze customer support.

10. Specifikationer

11. Garanti og support

For specific warranty information, technical support, or to report any issues with your SafeWaze FS99281-E harness, please contact SafeWaze customer service directly. Refer to the product packaging or the official SafeWaze webwebstedet for aktuelle kontaktoplysninger.

Fabrikant: SafeWaze

Dato først tilgængelig: 20. marts 2017