IBO OHI 25-60/180 Circulation Pump User Manual

1. Produktet er slutview

The IBO OHI 25-60/180 circulation pump, also known as a heating pump, facilitates the movement of heating water within a heating system. This pump model features a manual 3-speed regulator, allowing for system adaptation. It is suitable for use in heating and air conditioning systems with fluid temperatures ranging from +2°C to +110°C.

Nøglefunktioner omfatter:

• Manual 3-speed regulator for optimal system adaptation.
• Suitable for heating and air conditioning systems with fluid temperatures from +2°C to +110°C.
• Constructed with a ceramic shaft, graphite radial bearing, stainless steel bearing plate and rear pot, and a grey cast iron pump housing.
• Kompakt design for nem installation.
• Stille betjening.

Image 1: IBO OHI 25-60/180 Circulation Pump. This image displays the orange-colored pump unit with its black control panel, showing the speed selector and technical specifications. Two black rubber seals are visible at the bottom.

2. Sikkerhedsoplysninger

Læs alle instruktioner omhyggeligt før installation og betjening. Manglende overholdelse af disse instruktioner kan resultere i elektrisk stød, brand eller alvorlig personskade.

• Elektrisk sikkerhed: Ensure the power supply is disconnected before any installation, maintenance, or repair work. All electrical connections must be performed by a qualified electrician in accordance with local regulations. The pump requires a 230V, 50Hz power supply.
• Vandtemperatur: The pump handles fluid temperatures between +2°C and +110°C. Exercise caution when working with hot water to prevent burns.
• Tryk: The maximum operating pressure is 10 bar. Ensure the system components can withstand this pressure.
• Installationsmiljø: Install the pump in a dry, well-ventilated area, protected from frost and direct weather exposure.
• Personligt beskyttelsesudstyr: Always wear appropriate personal protective equipment (e.g., gloves, safety glasses) during installation and maintenance.

3. Installationsvejledning

Proper installation is crucial for the pump's efficient and safe operation.

3.1 Kontrol før installation

• Verify that the pump's specifications (voltage, frequency, pressure) match your system requirements.
• Ensure the installation location provides adequate space for mounting and future maintenance.
• Confirm that the piping system is clean and free of debris.

3.2 Montering af pumpen

1. The pump has an installation length of 180 mm. Ensure sufficient space between pipe connections.
2. Install the pump in the return line of the heating system, if possible, to extend its lifespan by operating at lower temperatures.
3. Ensure the motor shaft is horizontal to allow for proper lubrication of the bearings.
4. Use the provided seals (gaskets) to ensure a watertight connection to the piping. The connection diameter is 1 1/2"/1".
5. Tighten all connections securely but avoid over-tightening.

3.3 Elektrisk tilslutning

1. Sørg for, at hovedstrømforsyningen er afbrudt ved afbryderen.
2. Connect the pump to a 1 x 230 V, 50 Hz power supply.
3. The pump has an IP44 protection rating. Ensure the electrical connections are protected from moisture.
4. Follow the wiring diagram provided on the pump's terminal box cover.
5. Sørg for korrekt jording.

3.4 Systempåfyldning og udluftning

1. After installation, fill the heating system with water.
2. Vent the system thoroughly to remove any trapped air. Air in the system can cause noise and reduce pump efficiency.
3. The pump may have a manual vent screw; open it carefully until water flows out, then close it.

4. Betjeningsvejledning

The IBO OHI 25-60/180 pump features a manual 3-speed selector to adjust performance.

4.1 Første opstart

1. Ensure the system is filled with water and properly vented.
2. Turn on the main power supply to the pump.
3. Select a speed setting using the rotary switch on the pump's control panel.

4.2 hastighedsindstillinger

The pump offers three speed levels, each with different power consumption, maximum flow rate (Q max), and maximum head (H max):

• Niveau I: 46 W power consumption, 22 l/min maximum flow, 3 m maximum head.
• Niveau II: 63 W power consumption, 38 l/min maximum flow, 5 m maximum head.
• Niveau III: 93 W power consumption, 55 l/min maximum flow, 6 m maximum head.

Adjust the speed setting based on the heating system's requirements to achieve optimal circulation and energy efficiency.

5. Vedligeholdelse

Regular maintenance ensures the longevity and efficient operation of your circulation pump.

5.1 Rutinemæssige kontroller

• Visuel inspektion: Kontrollér pumpen regelmæssigt for tegn på lækager, korrosion eller skader på casing eller elektriske forbindelser.
• Støjniveau: Listen for any unusual noises during operation, which could indicate air in the system or a mechanical issue.
• Temperatur: Ensure the pump is not overheating.

5.2 Rengøring

Keep the exterior of the pump clean and free from dust and debris to ensure proper heat dissipation.

5.3 Vinterklargøring (hvis relevant)

If the heating system is to be shut down for an extended period in freezing temperatures, ensure the system, including the pump, is drained to prevent frost damage.

6. Fejlfinding

This section provides guidance for common issues. For complex problems, consult a qualified technician.

7. Tekniske specifikationer

8. Garanti og support

Information regarding the product warranty is not provided in the available data. For warranty claims, technical support, or spare parts inquiries, please contact the original seller or the manufacturer, 4U-Onlinehandel, directly. Keep your purchase receipt as proof of purchase.