1. Introduktion
This manual provides comprehensive instructions for the installation, operation, and maintenance of the FEIG ID ISC.PR100 Proximity Reader. Please read this manual thoroughly before using the device to ensure proper functionality and safety.
The FEIG ID ISC.PR100 is a high-performance proximity reader designed for various applications requiring reliable RFID tag detection. It operates at 13.56MHz and offers a significant reading range.
2. Sikkerhedsoplysninger
Overhold altid følgende sikkerhedsforanstaltninger for at forhindre personskade eller beskadigelse af enheden:
- Ensure the power supply matches the device's specifications (12-24VDC).
- Udsæt ikke enheden for ekstreme temperaturer, fugt eller direkte sollys.
- Undgå at tabe eller udsætte enheden for kraftige stød.
- Forsøg ikke at åbne eller reparere enheden selv. Overlad al service til kvalificeret personale.
- Afbryd strømmen, før du udfører nogen form for installation eller vedligeholdelse.
3. Produktet er slutview
The FEIG ID ISC.PR100 Proximity Reader is a compact and robust device. Key features include:
- Driftsfrekvens: 13.56MHz
- Input bindtage: 12-24VDC
- Maximum Signal Range: 180mm
- Interface: RS-232 / RS-485
- Supported Transponders: ISO-tags 15639
- Flash Memory: 64 kByte
- Beskyttelsesklasse: IP 30
Figure 3.1: FEIG ID ISC.PR100 Proximity Reader. This image shows the compact grey rectangular device with a visible connector port on one end, indicating its robust design for industrial applications.
4. Opsætning og installation
Follow these steps for proper installation of your ISC.PR100 Proximity Reader:
- Montering: Securely mount the reader in the desired location using appropriate fasteners. Ensure adequate ventilation and avoid mounting near strong electromagnetic interference sources.
- Strømtilslutning: Connect the 12-24VDC power supply to the designated power input terminals. Observe correct polarity.
- Datagrænsefladeforbindelse: Connect the reader to your host system using either the RS-232 or RS-485 interface, as required by your application. Refer to the device's pinout diagram for correct wiring.
- Antenneplacering: Position the reader's antenna (if external) or the integrated antenna area to optimize read range and performance for your specific transponders.
- Indledende opstart: Once all connections are secure, apply power to the device. The reader should perform a self-test and indicate readiness (e.g., via an LED indicator).
5. Betjeningsvejledning
The ISC.PR100 operates by detecting ISO-tags 15639 transponders within its read range. Operation is typically controlled by a host system via the connected interface (RS-232/RS-485).
5.1 Grundlæggende betjening
- Ensure the reader is powered on and connected to the host system.
- Place an ISO-tag 15639 transponder within the reader's effective range (up to 180mm).
- The reader will detect the transponder and transmit its data to the host system according to the configured communication protocol.
5.2 Kommunikationsprotokol
Detailed information regarding the communication protocol (commands, responses, data formats) for RS-232 and RS-485 interfaces can be found in the technical documentation provided by FEIG. It is essential to configure your host system to match the reader's communication settings (e.g., baud rate, parity, data bits, stop bits).
6. Vedligeholdelse
The FEIG ID ISC.PR100 Proximity Reader is designed for low maintenance. However, regular care can extend its lifespan and ensure optimal performance.
- Rensning: Use a soft, dry cloth to clean the exterior of the device. Do not use abrasive cleaners, solvents, or excessive moisture.
- Inspektion: Periodically inspect cables and connectors for any signs of wear or damage. Ensure all connections are secure.
- Miljø: Maintain the operating environment within the specified temperature and humidity ranges to prevent damage.
7. Fejlfinding
If you encounter issues with your ISC.PR100, refer to the following common problems and solutions:
| Problem | Mulig årsag | Løsning |
|---|---|---|
| Enheden tænder ikke. | Ingen strømforsyning; forkert lydstyrketage; faulty cable. | Check power connections and supply voltage. Ensure cables are not damaged. |
| Cannot read transponders. | Transponder out of range; incorrect transponder type; interference; faulty reader. | Ensure transponder is within 180mm range. Verify it's an ISO-tag 15639. Check for strong electromagnetic fields nearby. |
| Communication errors with host system. | Incorrect interface settings (baud rate, etc.); faulty data cable; software issue. | Verify communication settings match between reader and host. Check data cable integrity. Consult host system software documentation. |
If the problem persists after attempting these solutions, please contact FEIG technical support.
8. Specifikationer
| Parameter | Værdi |
|---|---|
| Model | ISC.PR100 |
| Operation Voltage | 12-24VDC |
| Strømforbrug | 5VA maksimum |
| Driftsfrekvens | 13.56 MHz |
| Maximum Signal Range | 180 mm |
| Interface | RS-232 / RS-485 |
| Understøttede transpondere | ISO-tags 15639 |
| Flash-hukommelse | 64 kByte |
| Beskyttelsesklasse | IP 30 |
| ASIN | B01E803L08 |
| Fabrikant | FEIG |
| Dato først tilgængelig | 1. april 2016 |
9. Garanti og support
For warranty information and technical support, please refer to the official FEIG website or contact your authorized distributor. Keep your purchase receipt as proof of purchase for warranty claims.
FEIG is committed to providing high-quality products and excellent customer service. Should you require assistance beyond the scope of this manual, do not hesitate to reach out to their support channels.
