Hubbell Lighting LHIRS1-G-WH LightHAWK vægafbrydersensor brugermanual

1. Introduktion

This manual provides detailed instructions for the installation, operation, and maintenance of the Hubbell Lighting LHIRS1-G-WH LightHAWK Wall Switch Sensor. This device is designed to automatically control lighting based on occupancy and ambient light levels, enhancing energy efficiency in various indoor environments.

2. Sikkerhedsoplysninger

ADVARSEL: Risk of electric shock. Installation should only be performed by a qualified electrician in accordance with all national and local electrical codes. Always turn off power at the circuit breaker or fuse box before installing or servicing this device. Failure to follow these instructions may result in serious injury or death.

• Sørg for, at strømmen er afbrudt før installation.
• Do not install with wet hands or while standing on wet surfaces.
• Denne enhed er kun til indendørs brug.
• Use only with compatible lighting loads as specified.

3. Produktet er slutview

3.1 Nøglefunktioner

• Digital Passive Infrared (PIR) sensor for accurate occupancy detection.
• IntelliDAPT self-adaptive technology for optimized performance.
• Supports Occupancy (auto-on) and Vacancy (manual-on) operating modes.
• Integrated photocell for daylight harvesting capabilities.
• Single circuit control for lighting.
• Designed for 120/277VAC applications.
• Covers up to 1000 sq. ft.

3.2 Komponenter

The Hubbell LightHAWK Wall Switch Sensor consists of the following primary components:

• PIR-sensorlinse: Registrerer bevægelse inden for sit felt view.
• Kontrolknap: Allows for manual override or mode selection.
• Indikatorlys: Provides visual feedback on sensor status.
• Fotocelle: Measures ambient light levels to optimize lighting control.

Figur 1: Forside view of the Hubbell LightHAWK Wall Switch Sensor. This image displays the front of the white Hubbell LightHAWK Wall Switch Sensor. It features a large rectangular sensor lens at the top, a smaller rectangular button below it, and a small indicator light at the bottom center, all set within a standard wall plate.

4. Installation og opsætning

Proper installation is crucial for optimal performance. This sensor requires a Universal Voltage Power Pack (Models UVPP or UVPPM) for operation, which is sold separately.

4.1 Trin før installation

1. Sluk for strømmen: Locate the circuit breaker or fuse controlling the light fixture and turn off the power. Verify power is off using a voltage tester.
2. Forbered ledningsføring: Ensure the electrical box has the necessary wiring (line, load, neutral, ground) for the sensor and power pack.
3. Consult Power Pack Manual: Refer to the instruction manual for your specific Universal Voltage Power Pack (UVPP or UVPPM) for detailed wiring diagrams and instructions, as this sensor integrates with it.

4.2 Wiring the Sensor

Connect the sensor to the Universal Voltage Power Pack and the lighting load according to the wiring diagram provided with the power pack. Typically, connections will include:

• Lav voltage wires from the sensor to the power pack.
• Høj voltage wires from the power pack to the lighting load and line voltage.

Ensure all wire connections are secure and insulated with wire nuts.

4.3 Montering

Mount the sensor in a standard wall box. Ensure the sensor lens has an unobstructed view of the area to be controlled. Avoid mounting near heat sources, air vents, or in direct sunlight, which can interfere with sensor performance.

5. Betjeningsvejledning

The LightHAWK sensor offers flexible operation modes to suit different needs.

5.1 driftstilstande

• Occupancy (Auto-ON): In this mode, the lights automatically turn ON when occupancy is detected and turn OFF after a preset time delay when the space becomes vacant. This is ideal for high-traffic areas.
• Vacancy (Manual-ON): In this mode, the lights must be manually turned ON using the control button. They will then automatically turn OFF after a preset time delay when the space becomes vacant. This mode is suitable for areas where manual control of initial lighting is preferred.

5.2 Adjusting Settings (IntelliDAPT and Photocell)

The sensor features IntelliDAPT technology, which continuously analyzes the environment and automatically adjusts sensitivity and time delay settings for optimal performance. The integrated photocell also contributes to energy savings by preventing lights from turning on if sufficient natural light is present.

Specific adjustments for time delay, sensitivity, and photocell settings are typically performed via the control button or through a dedicated programming method. Refer to the detailed programming guide for the LHIRS1-G-WH sensor for precise instructions on how to configure these settings.

6. Vedligeholdelse

The Hubbell LightHAWK Wall Switch Sensor requires minimal maintenance.

• Rensning: Periodically wipe the sensor lens with a soft, dry cloth to remove dust or debris that may obstruct its view. Brug ikke slibende rengøringsmidler eller opløsningsmidler.
• Inspektion: Regularly check for any visible damage to the sensor or wiring. If damage is found, disconnect power and have it inspected by a qualified electrician.

7. Fejlfinding

If the sensor is not functioning as expected, review følgende almindelige problemer:

If problems persist after attempting these solutions, contact Hubbell Lighting technical support or a qualified electrician.

8. Specifikationer

9. Garanti og support

For specific warranty information, please refer to the documentation included with your product at the time of purchase or visit the official Hubbell Lighting website. Technical support and further assistance can be obtained by contacting Hubbell Lighting directly.

You can find more products and information from the brand at the Hubbell Store.