1. Introduktion
This manual provides detailed instructions for the proper installation, safe operation, and general maintenance of your Harbor Breeze Model 40412 Candelabra Base Lamp Socket. This product is designed as a replacement light socket for ceiling fans and is intended for indoor use only. It features a candelabra base and threaded socket for secure bulb installation.
2. Vigtige sikkerhedsoplysninger
ADVARSEL: To avoid fire, shock, or serious injury, always turn off power at the circuit breaker or fuse box before installing, servicing, or cleaning this product. Consult a qualified electrician if you are unsure about wiring procedures. Always follow local electrical codes.
- Sørg for, at strømforsyningen er afbrudt, før installationen påbegyndes.
- This product is for indoor use only. Do not expose to water or excessive moisture.
- Overskrid ikke det maksimale wattage rating of 120 watts for the bulb used in this socket.
- Inspect the socket and wiring for any damage before installation.
3. Pakkens indhold
- Harbor Breeze Model 40412 Lysestagefod Lamp Socket with Wires

Figur 1: The Harbor Breeze Model 40412 Candelabra Base Lamp Socket. This image shows the white ceramic socket with internal threading, two metal mounting tabs, and two electrical wires (one white, one black) extending from the top, partially covered by a white braided sleeve.
4. Installationsvejledning
Denne lamp socket is designed for replacement in existing fixtures, typically ceiling fans. Ensure you have basic electrical tools such as wire strippers, screwdrivers, and wire nuts.
- Afbryd strømmen: Before starting, turn off the power to the fixture at the main circuit breaker or fuse box. Verify power is off using a voltage tester.
- Access Existing Socket: Carefully disassemble the light kit portion of your ceiling fan or fixture to access the existing lamp socket and its wiring.
- Remove Old Socket: Disconnect the wires from the old socket. Note which wire (typically black) connects to the "hot" or power wire and which (typically white) connects to the "neutral" wire. Remove any mounting screws or clips holding the old socket in place.
- Prepare New Socket: If necessary, strip a small amount of insulation (approximately 3/8 inch) from the ends of the new socket's wires.
- Tilslut ledninger:
- Connect the black wire from the new socket to the "hot" (usually black) wire from the fixture using a wire nut.
- Connect the white wire from the new socket to the "neutral" (usually white) wire from the fixture using a wire nut.
- Ensure all connections are secure and no bare wire is exposed outside the wire nuts.
- Mount New Socket: Sikre den nye lamp socket into the fixture using its integrated mounting tabs and appropriate screws (not included, typically reused from the old socket or provided with the fixture). Ensure it is firmly in place.
- Saml armaturet igen: Carefully reassemble the light kit and any covers removed during the process.
- Gendan strøm: Tænd for strømmen igen ved afbryderen.
5. Betjening
Once installed, operating the lamp socket is straightforward:
- Indsæt pære: Screw a candelabra base (E12) light bulb into the socket. Ensure the bulb's wattage ikke overstiger 120 watt.
- Aktiver strøm: Turn on the light switch or pull chain connected to the fixture. The bulb should illuminate.
6. Vedligeholdelse
The Harbor Breeze lamp socket requires minimal maintenance. Regular inspection can help ensure continued safe operation.
- Rensning: Ensure power is off before cleaning. Wipe the exterior of the socket with a dry, soft cloth. Do not use liquid cleaners or abrasive materials.
- Inspektion: Periodically check the socket for any signs of damage, such as cracks, discoloration, or loose connections. If any damage is observed, discontinue use and replace the socket.
- Udskiftning af pære: Always turn off power to the fixture before replacing a light bulb. Allow the old bulb to cool completely before removal.
7. Fejlfinding
If the light does not illuminate after installation, consider the following common issues:
- Ingen strøm: Check the circuit breaker or fuse box to ensure power is on. Test the circuit with a voltage tester.
- Loose Bulb: Ensure the light bulb is screwed in firmly.
- Defekt pære: Test the socket with a new, known-good light bulb.
- Forkert ledningsføring: Turn off power and re-check all wire connections. Ensure they are secure and correctly matched (hot to hot, neutral to neutral).
- Damaged Socket: If the socket appears damaged or discolored, it may need replacement.
Hvis fejlfindingstrinene ikke løser problemet, skal du kontakte en kvalificeret elektriker.
8. Specifikationer
| Modelnummer | 40412 |
| Mærke | HAVNEBRIS |
| Produktdimensioner | 4.5 x 1.5 x 3.25 tommer |
| Varens vægt | 1.12 ounce |
| Monteringstype | Loftmontering |
| Maks. Watttage | 120 watt |
| Sokkeltype | Candelabra Base (E12) |
| Tilsigtet brug | Indoor use only, replacement for ceiling fan light kits |
| UPC | 671961404123, 701327283373 |
9. Garanti og support
Specific warranty information for the Harbor Breeze Model 40412 Candelabra Base Lamp Socket is not provided in this manual. For details regarding warranty coverage, please refer to the original product packaging, contact the retailer where the product was purchased, or visit the official Harbor Breeze webwebsted.
For technical support or further assistance, please contact Harbor Breeze customer service through their official channels.





