Defiant 180 Degree Motion Security Light User Manual

Indledning

Thank you for choosing the Defiant 180 Degree Motion Security Light. This outdoor motion-sensing security light is designed to provide enhanced safety and energy efficiency for your property. It features a wide 180-degree, 70 ft. motion sensor for reliable activation and is Energy Star qualified. This manual provides detailed instructions for installation, operation, maintenance, and troubleshooting to ensure optimal performance and longevity of your security light.

Sikkerhedsoplysninger

Læs og forstå alle instruktioner, før du påbegynder installationen. Manglende overholdelse af disse instruktioner kan resultere i elektrisk stød, brand eller andre farer, der kan forårsage personskade eller materielle skader.

• ADVARSEL: Risiko for elektrisk stød. Afbryd strømmen til sikringen eller strømafbryderen før installation eller servicering.
• ADVARSEL: Risk of fire. Use only PAR38 incandescent (dimmable outdoor wet rated) or select PAR38 dimmable LED outdoor rated-wet rated bulbs. Do not exceed 120 watts per bulb.
• Kontakt en kvalificeret elektriker, hvis du er usikker på installationsprocessen.
• Install the fixture in a location suitable for outdoor use, away from flammable materials.
• Sørg for, at alle forbindelser er sikre og korrekt isolerede.
• Operating temperature range: -25°C (-13°F) to +50°C (+120°F).

Pakkens indhold

Kontroller, at alle komponenter er til stede, før installationen påbegyndes:

• Defiant 180 Degree Motion Security Light Fixture
• Monteringsudstyr (skruer, trådmøtrikker)
• Instruktionsmanual
• Note: Bulbs are not included.

Opsætning og installation

1. Montering af armaturet

Choose a suitable mounting location on a wall or eave. The motion sensor works best when mounted 6-10 feet above the ground. Ensure the sensor has an unobstructed view af det område, du ønsker at overvåge.

Figur 1: Front view of the Defiant 180 Degree Motion Security Light, showing the two adjustable light heads and the motion sensor unit below.

1. Sluk for strømmen ved afbryderen eller sikringsboksen.
2. Remove the existing fixture (if any) and disconnect wiring.
3. Fastgør monteringsbeslaget til samledåsen ved hjælp af de medfølgende skruer.
4. Pull the electrical wires through the center hole of the mounting bracket.

2. Ledningsforbindelser

Make sure power is still off before proceeding with wiring.

1. Tilslut sort ledningen fra armaturet til sort (varm) ledning fra samledåsen ved hjælp af en trådmøtrik.
2. Tilslut hvid ledningen fra armaturet til hvid (neutral) ledningen fra samledåsen ved hjælp af en trådmøtrik.
3. Tilslut grøn or bare copper (ground) wire from the fixture to the jord wire from the junction box using a wire nut.
4. Stik forsigtigt alle ledninger ind i samledåsen.

3. Securing the Fixture and Installing Bulbs

Figur 2: Side view of the security light, illustrating the adjustable swivel arms for positioning the light heads and sensor.

1. Juster armaturet med monteringsbeslaget, og fastgør det med de medfølgende skruer.
2. Install two PAR38 bulbs (up to 120 watts each, not included) into the sockets. Ensure bulbs are outdoor wet-rated.
3. Adjust the swivel arms and light heads to direct the light as desired.
4. Adjust the motion sensor's field of vision using its adjustable head.

Figur 3: Close-up of a light fixture, showing the protective bulb shield and the textured reflector surface.

Betjeningsvejledning

Once installed, turn on the power at the circuit breaker. The light will enter a warm-up period for approximately 30-60 seconds before becoming fully operational.

Indstillinger for bevægelsessensor

The motion sensor has adjustable settings, typically located on the bottom or side of the sensor unit.

• Registreringsområde: Adjust the sensitivity to control the detection distance (up to 70 ft.).
• Tidsindstilling: Select how long the light stays on after motion is detected (e.g., 1 minute, 5 minutes, 20 minutes).
• Dusk-to-Dawn-funktion: The light automatically deactivates during daylight hours to conserve energy. It will only activate with motion during nighttime.
• AlertFlash: This feature causes the lights to flash when motion is detected before illuminating to full brightness, providing an additional deterrent.
• DualBrite 2-level lighting: Provides energy-saving accent light at half power and full-power security light when motion is detected. (Note: Some models may not include this feature despite product descriptions.)

Refer to the specific labels on your sensor for exact dial positions and functions.

Opretholdelse

Regular maintenance ensures optimal performance and extends the life of your security light.

• Rensning: Periodically wipe the fixture and sensor lens with a soft, damp klud til at fjerne snavs og rester. Brug ikke slibende rengøringsmidler eller opløsningsmidler.
• Udskiftning af pære:
  1. Turn off power at the circuit breaker before replacing bulbs.
  2. Lad pærerne køle helt af, før de håndteres.
  3. Unscrew the old bulb and screw in a new PAR38 incandescent (dimmable outdoor wet rated) or select PAR38 dimmable LED outdoor rated-wet rated bulb (up to 120 watts).
  4. The bulb-saver feature extends bulb life up to 4 times the life of standard bulbs.
• Inspektion: Annually inspect wiring for any signs of wear or damage.

Fejlfinding

If your security light is not functioning as expected, refer to the following common issues and solutions:

Specifikationer

Garanti og support

Defiant products are manufactured to high-quality standards and are warranted to be free from defects in materials and workmanship for a specified period from the date of purchase. For warranty claims or technical support, please refer to the contact information provided on the product packaging or visit the official Defiant webwebsted.

Gem venligst din købsbevis af garantihensyn.