KeylessOption Key Fob Instruction Manual

Indledning

This manual provides detailed instructions for the KeylessOption 3-button key fob remote, model KPT1660, designed as a replacement for compatible Toyota and Pontiac vehicles. It includes information on product components, vehicle compatibility, programming procedures, and general usage.

Billede: Forside view of the KeylessOption 3-button key fob remote, showing Lock, Unlock, and Trunk/Panic buttons.

Hvad er inkluderet

Image: The package contents, including the key fob remote, a ring loop, and a pre-installed CR2032 battery.

• KeylessOption 3-button remote (Model KPT1660)
• Forudinstalleret CR2032 batteri
• Programming instructions guide

Kompatibilitet

This key fob is compatible with specific Toyota and Pontiac vehicle models and years. Please verify your vehicle's original keyless entry system and FCC ID to ensure compatibility.

Image: The front and back of the key fob, highlighting the FCC ID GQ43VT14T and Part Number 89742-AA030 for compatibility verification.

Kompatible køretøjer:

• Toyota Camry: 1999-2006
• Toyota Solara: 1998-2003
• Toyota Matrix: 2003-2008
• Toyota Sienna: 1998-2003
• Pontiac Vibe: 2003-2008

Vigtig bemærkning: This item will not work if your original remote has a red light indicator. Ensure your vehicle is equipped with factory original keyless entry.

FCC ID: GQ43VT14T

Varenummer: 89742-AA030

Opsætning og programmering

The KeylessOption key fob is designed for self-programming. Follow these step-by-step instructions carefully. All steps must be performed within the specified timeframes.

Image: Graphic indicating "DIY Self Programming" for the key fob, emphasizing it is fast, easy, and free.

Programmeringsprocedure:

1. Forberedelse:
   • Ensure the key is out of the ignition.
   • The driver's door must be open, all other doors closed and locked.
   • The driver's door must be unlocked.
2. Initial Key Cycle (within 5 seconds):
   • Insert the key into the ignition (DO NOT Turn). Pull the key out.
   • Insert the key into the ignition (DO NOT Turn). Pull the key out.
3. Door Cycle 1 (within 40 seconds):
   • Close then open the driver's door.
   • Close then open the driver's door.
   • Insert the key into the ignition (DO NOT Turn). Pull the key out.
4. Door Cycle 2 and Ignition (within 40 seconds):
   • Close then open the driver's door.
   • Close then open the driver's door.
   • Sæt nøglen i tændingen, og lad den blive i tændingen.
   • Close the driver's door.
   • Turn the ignition to ON (DO NOT Start) then back to OFF.
   • Fjern nøglen fra tændingen.
5. Programming Mode Confirmation:
   • Within 3 seconds, the power door locks should lock then unlock automatically. This indicates successful entry into programming mode. If locks do not cycle, return to step 1.
6. Remote Programming (within 40 seconds):
   • Tryk på LÅSE og LÅS OP buttons on the remote simultaneously for 1.5 seconds.
   • Immediately after releasing den LÅSE og LÅS OP knapperne, tryk på LÅSE button by itself and hold for 2 seconds.
   • Within 3 seconds, the door locks should lock and then unlock once, indicating successful programming. If the door locks cycle twice, repeat the previous two sub-steps (pressing LOCK and UNLOCK simultaneously, then LOCK alone) as the remote was not accepted.
   • Repeat the previous two sub-steps for each additional new remote you wish to program.
7. Afslut programmeringstilstand:
   • Open the driver's door to exit programming mode.

Operating the Key Fob

The KeylessOption key fob features three distinct buttons for controlling your vehicle's keyless entry functions.

Image: Diagram showing the front of the key fob with labels pointing to the Lock, Unlock, and Trunk/Panic buttons.

• LÅS -knap: Tryk én gang for at låse alle bildøre.
• LÅS OP-knap: Tryk én gang for at oplåse alle bildøre.
• TRUNK / PANIC Button: This button typically activates the trunk release. Holding this button down for a few seconds will activate the vehicle's panic alarm.

Billede: Bagside view of the key fob, showing the red panic button.

Opretholdelse

Udskiftning af batteri:

The key fob uses one CR2032 lithium coin cell battery. When the remote's range decreases or it stops responding, it may be time to replace the battery.

1. Carefully pry open the key fob casing ved hjælp af en lille flad skruetrækker eller et lirkende værktøj.
2. Locate the CR2032 battery inside the casing.
3. Remove the old battery, noting its orientation (positive side up).
4. Indsæt et nyt CR2032-batteri med den positive (+) side opad.
5. Snap the key fob casing forsvarligt sammen igen.

Generel pleje:

• Avoid exposing the key fob to extreme temperatures, direct sunlight for prolonged periods, or moisture.
• Do not drop the key fob or subject it to strong impacts.
• Clean the exterior with a soft, dry cloth if necessary.

Fejlfinding

Specifikationer

• Modelnummer: KPT1660
• FCC ID: GQ43VT14T
• Produktdimensioner: 2 x 0.75 x 4 tommer
• Varens vægt: 0.317 ounce
• Batteritype: 1 x CR2032 (præ-installeret)
• Farve: Sort

Garanti og support

KeylessOption products are designed for reliability and performance. For any issues or questions regarding your key fob, please contact KeylessOption customer support.

While specific warranty details are not provided in this manual, KeylessOption is committed to customer satisfaction. For support, please visit the official KeylessOption store on Amazon or contact their customer service directly through your purchase platform.

You can find more information and contact details by searching for "KeylessOption" on Amazon or by visiting their brand store:

Visit the KeylessOption Amazon Store