1. Introduktion
This manual provides essential information for the safe and efficient operation, setup, and maintenance of your Holzmann Professional Miter Saw KAP 305JL and the accompanying Machine Stand USK 2760. Please read this manual thoroughly before initial use to ensure proper handling and to prevent injury or damage to the equipment.
The Holzmann KAP 305JL is a professional sliding miter saw designed for precise cutting of various materials, featuring a quiet belt drive and a laser guide for accuracy. The USK 2760 machine stand provides a stable and versatile platform for your saw, enhancing portability and workspace efficiency.
2. Sikkerhedsinstruktioner
Prioritér altid sikkerheden, når du bruger elværktøj. Manglende overholdelse af disse instruktioner kan resultere i alvorlig personskade eller materielle skader.
- Læs manualen: Gør dig bekendt med alle betjeningselementer, justeringer og betjeningsprocedurer inden brug.
- Brug personlige værnemidler (PPE): Always wear safety glasses, hearing protection, and a dust mask. Gloves are recommended for handling materials but should be avoided near rotating parts.
- Ensure Stable Work Area: Operate the saw on a firm, level surface. The USK 2760 stand is designed for stability, but ensure its legs are fully extended and locked.
- Sikkert arbejdsemne: Altid clamp the workpiece firmly before cutting. Never hold it by hand.
- Hold vagter på plads: Ensure all safety guards are properly installed and functioning before operation.
- Tag stikket ud før justeringer: Frakobl saven fra strømkilden, før du foretager justeringer, skifter klinger eller udfører vedligeholdelse.
- Undgå at overrække: Oprethold korrekt fodfæste og balance til enhver tid.
- Hold området ryddet: Sørg for, at arbejdsområdet er rent, godt oplyst og fri for forhindringer.
- Brug det rigtige blad: Only use sharp, correctly sized blades suitable for the material being cut.
- Elektrisk sikkerhed: Ensure the power supply matches the tool's requirements (230 Volts). Do not use in damp eller våde forhold.
3. Pakkens indhold
Upon unpacking, verify that all components are present and undamaged. If any items are missing or damaged, contact your dealer immediately.
- Holzmann KAP 305JL Professional Miter Saw
- Holzmann USK 2760 Universal Machine Stand
- Tungsten Carbide Circular Saw Blade (pre-installed or separate)
- Laser Guide (integrated)
- Table Spreader / Workpiece Support
- Dybdestop
- Telescopic Backstop
- Brugervejledning (dette dokument)
Figure 3.1: Holzmann KAP 305JL Miter Saw and USK 2760 Machine Stand as a complete set.
4. Opsætning
4.1 Assembling the USK 2760 Machine Stand
- Unfold the main frame of the stand. Ensure all locking mechanisms for the legs are securely engaged.
- Attach the telescopic workpiece supports to both ends of the main frame. These supports can be extended and adjusted for height to accommodate longer workpieces.
- Verify the stand is stable and level on your work surface. Adjust leg extensions if necessary.
Figure 4.1: The Holzmann USK 2760 Universal Machine Stand, ready for saw mounting.
4.2 Mounting the KAP 305JL Miter Saw to the Stand
- Position the KAP 305JL miter saw onto the mounting brackets of the USK 2760 stand.
- Secure the saw to the stand using the provided bolts and nuts. Ensure the saw is firmly attached and does not wobble.
- Adjust the height of the telescopic workpiece supports on the stand so they are level with the saw's cutting table.
Figur 4.2: Nærbillede view of the Holzmann KAP 305JL Miter Saw, showing the blade and angle adjustment mechanisms.
5. Betjeningsvejledning
5.1 Grundlæggende betjening
- Strømtilslutning: Tilslut saven til en passende 230V stikkontakt.
- Placering af emne: Place the workpiece firmly against the fence and on the saw table. Use the telescopic backstop for repetitive cuts.
- Clamping: Secure the workpiece with the integrated clamp to prevent movement during cutting.
- Activating Laser Guide: Turn on the laser guide for precise cut line indication.
- Start af saven: Tryk på tænd/sluk-knappen for at starte motoren. Lad klingen nå fuld hastighed, før du begynder at save.
- Gør snittet:
- For straight cuts, gently push the saw head down through the workpiece.
- For sliding cuts (crosscuts on wider material), pull the saw head towards you, lower it into the workpiece, and then push it smoothly through the material.
- Færdiggørelse af snittet: Når savningen er færdig, slip tænd/sluk-knappen og lad klingen stoppe helt, før savhovedet hæves.
5.2 Vinkeljusteringer
The KAP 305JL allows for precise miter and bevel angle adjustments:
- Miter Angle (Horizontal): Loosen the miter lock knob, rotate the turntable to the desired angle (up to 45° left/right), and re-tighten the knob. Common detents are provided for quick setting.
- Bevel Angle (Vertical): Loosen the bevel lock lever, tilt the saw head to the desired angle (up to 45° left/right), and re-tighten the lever.
- Sammensatte snit: Combine both miter and bevel adjustments for compound angle cuts.
6. Vedligeholdelse
Regular maintenance ensures the longevity and optimal performance of your Holzmann miter saw.
- Rensning: After each use, unplug the saw and use a brush or vacuum to remove sawdust and debris from the motor vents, blade guard, and table. Do not use solvents.
- Udskiftning af knive:
- Tag stikket ud af saven.
- Raise the blade guard.
- Brug den medfølgende skruenøgle til at løsne spindelmøtrikken, mens du holder spindellåseknappen nede.
- Fjern forsigtigt det gamle blad, og monter det nye blad, og sørg for, at tænderne er vendt korrekt.
- Spænd spindelmøtrikken forsvarligt.
- Smøring: Periodically apply a light coat of machine oil to the sliding rails to ensure smooth operation.
- Inspektion: Regularly inspect the power cord for damage, check all fasteners for tightness, and ensure the blade is sharp and free of damage.
7. Fejlfinding
Dette afsnit omhandler almindelige problemer, du kan støde på. Kontakt kvalificeret servicepersonale ved problemer, der ikke er nævnt her.
| Problem | Mulig årsag | Løsning |
|---|---|---|
| Saven starter ikke | No power supply; Faulty switch; Overload protection tripped | Check power connection; Test switch; Reset circuit breaker |
| Blade not cutting smoothly / Burning wood | Dull blade; Incorrect blade for material; Workpiece not secured | Replace blade; Use appropriate blade; Secure workpiece firmly |
| Overdreven vibration | Løst blad; Beskadiget blad; Ustabilt stativ | Tighten blade arbor nut; Replace damaged blade; Ensure stand is stable and locked |
| Laservejledning ikke synlig | Laser dirty; Laser malfunction | Clean laser lens; Contact service if malfunction persists |
8. Specifikationer
Technical data for the Holzmann KAP 305JL Miter Saw:
- Model: KAP 305JL
- Strømforsyning: 230 volt
- Magt: 1.8 kW (1800 watt)
- Hastighed uden belastning: 4500 rpm
- Bladets diameter: (Typically 305mm for KAP 305JL, not explicitly stated in specs but implied by model number)
- Geringskapacitet: -45° til +45°
- Skråningskapacitet: -45° til +45° (venstre/højre)
- Særlige funktioner: Laser guide, Belt drive, Bevel capacity, Telescopic backstop
- Weight (Saw): Cirka 28 kg
- Håndtag Materiale: Plast eller gummi
- Anbefalet overflade: Aluminium (implies suitability for non-ferrous metals and wood)
Technical data for the Holzmann USK 2760 Machine Stand:
- Model: USK 2760
- Type: Universal Machine Stand
- Funktioner: Telescopic workpiece supports, Foldable design
9. Garanti og support
Holzmann products are manufactured to high-quality standards. For warranty information, please refer to the documentation provided at the time of purchase or contact your authorized Holzmann dealer.
For technical support, spare parts, or service inquiries, please contact the retailer where you purchased the product or visit the official Holzmann website for contact information. Please note that information regarding spare parts availability for this specific model is not readily available in general product specifications, so direct inquiry is recommended.
Always provide the model number (KAP 305JL, USK 2760) and serial number (if applicable) when contacting support.
