PAC LP5-2 LOC PRO-seriens 2-kanals linjeudgangskonverter brugermanual

Indledning

The PAC LP5-2 L.O.C. PRO Series 2-Channel Line Output Converter is engineered to optimize audio levels between your vehicle's radio and an aftermarket amplifier. This device ensures the best audio performance and helps to avoid unwanted noise, making it ideal for integrating an amplifier into an OEM (Original Equipment Manufacturer) audio system. It features a full 20-20kHz +/-1.5dB frequency response and a single-dial, precision-matched stereo gain adjustment.

Sikkerhedsoplysninger

• Always disconnect the vehicle's battery negative terminal before installing any electrical components to prevent electrical shock or damage.
• Sørg for, at alle ledningsforbindelser er sikre og korrekt isolerede for at forhindre kortslutninger.
• Do not install the device in locations where it may be exposed to excessive heat, moisture, or direct sunlight.
• Kontakt en professionel installatør af bilstereo, hvis du er usikker på nogen del af installationsprocessen.
• This product is designed for 12V DC automotive electrical systems only.

Pakkens indhold

Image: The PAC LP5-2 Line Output Converter unit, a multi-wire harness with RCA connectors, and a small blue-handled screwdriver.

• PAC LP5-2 Line Output Converter Unit
• Wiring Harness with RCA Outputs
• Small Screwdriver (for gain adjustment)

Opsætning og installation

The LP5-2 converts speaker-level audio signals from your factory radio into low-level RCA signals, which are required by most aftermarket amplifiers. Follow these general steps for installation:

1. Afbryd batteriet: Før start skal du frakoble den negative pol på dit køretøjs batteri.
2. Identificér højttalerledninger: Locate the speaker output wires from your factory radio or amplifier. You will need to identify the positive and negative wires for the left and right channels.
3. Tilslut indgangsledninger: Connect the speaker-level input wires from the LP5-2 harness to the corresponding speaker wires from your factory system. Ensure correct polarity (positive to positive, negative to negative).
   • Typically, the LP5-2 harness will have clearly labeled wires for Left Speaker (+/-) and Right Speaker (+/-).
4. Tilslut strøm og jord: Connect the LP5-2's power wire (usually red) to a switched 12V power source, and the ground wire (usually black) to a solid chassis ground point.
5. Connect Remote Turn-On: The LP5-2 features a remote turn-on output (usually blue wire) that can be used to turn on your aftermarket amplifier. Connect this wire to the remote input of your amplivligere.
6. Tilslut RCA-udgange: Plug the RCA cables from the LP5-2's output into the RCA input jacks of your aftermarket amplifier. Ensure left output connects to left input and right output to right input.
7. Monter enheden: Securely mount the LP5-2 unit in a dry, accessible location, away from excessive heat or moving parts.
8. Gentilslut batteri: Når alle tilslutninger er foretaget og verificeret, skal du tilslutte bilens batteris negative pol igen.

Betjeningsvejledning

The PAC LP5-2 features a single-dial gain adjustment to match the output level of the converter to the input sensitivity of your amplifier. This adjustment is crucial for achieving optimal sound quality and preventing distortion.

1. Indledende forstærkningsindstilling: Start with the gain adjustment dial on the LP5-2 set to its minimum (fully counter-clockwise) position.
2. AmpIndstilling af forstærkning: Set the gain control on your aftermarket amplifier to its minimum position as well.
3. Afspil lyd: Play a familiar piece of music through your vehicle's audio system at a moderate volume level (around 75% of maximum radio volume).
4. Juster LP5-2 forstærkning: Slowly turn the gain adjustment dial on the LP5-2 clockwise using the provided screwdriver until you hear a slight distortion in the audio. Then, back off the gain slightly until the distortion disappears. This sets the optimal output level from the converter.
5. Tilpasse Amplifier gevinst: Now, slowly increase the gain on your aftermarket amplifier until the desired volume and sound quality are achieved without distortion.
6. Finjustering: Listen carefully for any distortion at higher volumes. If distortion occurs, slightly reduce the gain on either the LP5-2 or the amplifier until the sound is clear.

Note: Proper gain matching is essential for clear, powerful audio. Incorrect settings can lead to distorted sound or damage to your speakers and amplivligere.

Opretholdelse

The PAC LP5-2 is designed for maintenance-free operation. To ensure its longevity:

• Hold enheden fri for støv og snavs.
• Sørg for, at alle ledningsforbindelser forbliver fastgjorte og fri for korrosion.
• Undgå at udsætte enheden for ekstreme temperaturer eller fugt.

Fejlfinding

Specifikationer

• Model: LP5-2
• Kanaler: 2-kanal
• Indgangstype: Højttaler niveau
• Outputtype: RCA Level
• Frekvensrespons: 20Hz - 20kHz (+/-1.5dB)
• Forstærkningsjustering: Single dial, precision matched stereo
• Dimensioner: Cirka 4 x 8 x 1.25 tommer (10.16 x 20.32 x 3.175 cm)
• Vægt: Cirka 0.11 kg
• UPC: 606523109437

Garanti og support

For warranty information or technical support, please refer to the official PAC webwebstedet eller kontakt deres kundeserviceafdeling. Gem din købskvittering som købsbevis i tilfælde af garantikrav.

Note: Product specifications and features are subject to change without notice. Always refer to the latest information provided by the manufacturer.