Byron Belyst Kablet Ringetryk 7960B Brugsanvisning

1. Introduktion

Thank you for choosing the Byron 7960B Illuminated Wired Bell Push. This manual provides essential information for the safe installation, operation, and maintenance of your new bell push. Please read these instructions carefully before installation and retain them for future reference.

2. Produktet er slutview

The Byron 7960B is a surface-mounted, wired bell push featuring a durable brass finish and an illuminated button for enhanced visibility. It is designed to be connected to an existing wired doorbell chime system.

Et nærbillede view of the Byron 7960B Illuminated Wired Bell Push, featuring a polished brass rectangular housing and a central clear push button with a brass center. The design is suitable for surface mounting.

3. Sikkerhedsoplysninger

• Always disconnect power to the doorbell circuit at the main fuse box or circuit breaker before attempting any installation or maintenance.
• Hvis du er usikker på nogen del af installationsprocessen, skal du kontakte en kvalificeret elektriker.
• This product is designed for low-voltage wired doorbell systems. Do not connect to mains voltage direkte.
• Ensure all wiring connections are secure and insulated to prevent short circuits.
• Hold emballagemateriale væk fra børn.

4. Pakkens indhold

• Byron 7960B Illuminated Wired Bell Push
• Monteringsskruer
• Micro LED Bulb (for illumination)

5. Opsætning og installation

5.1. Nødvendigt værktøj

• Screwdriver (appropriate for mounting screws)
• Bor (hvis der er behov for nye monteringshuller)
• Trådstrippere
• Blyant

5.2. Ledningsinstruktioner

1. Afbryd strømmen: Before starting, ensure the power to your existing doorbell system is turned off at the main electrical panel.
2. Remove Old Bell Push (if applicable): Carefully remove your old bell push, noting how the wires are connected.
3. Forbered ledninger: Gently strip a small amount of insulation (approximately 1/4 inch) from the ends of the two low-voltage doorbell wires.
4. Tilslut ledninger: Connect one doorbell wire to each of the two terminals on the back of the Byron 7960B bell push. Ensure connections are tight and secure.

5.3. Connecting the Illumination LED

The micro LED bulb for illumination needs to be connected manually. This process can be delicate:

1. Locate the two small wires extending from the micro LED bulb.
2. Carefully connect these LED wires to the same two terminals where the main doorbell wires are connected. The LED is typically non-polarised, so the orientation of its wires usually does not matter for basic function, but if it doesn't light up, try reversing the LED wire connections.
3. Ensure all four wire connections (two doorbell, two LED) are securely fastened to the two terminals on the bell push.

5.4. Monteringsvejledning

1. Placering: Hold the bell push in the desired mounting location. Use a pencil to mark the positions for the mounting screws.
2. Bor pilothuller: If necessary, drill small pilot holes at the marked positions.
3. Secure Bell Push: Feed the doorbell wires through the opening in the back of the bell push. Align the bell push with the pilot holes and secure it firmly to the surface using the provided mounting screws. Do not overtighten.
4. Gendan strøm: Once the bell push is securely mounted and all connections are made, restore power to the doorbell circuit at your main electrical panel.

6. Betjening

After successful installation and power restoration, the LED in the bell push should illuminate, indicating it is ready for use. Press the button firmly to activate your doorbell chime. The bell push is designed for momentary contact, meaning the chime will sound only while the button is pressed.

7. Vedligeholdelse

• Rensning: To maintain the brass finish, wipe the bell push regularly with a soft, dry cloth. Avoid abrasive cleaners or chemicals that could damage the finish.
• Inspektion: Periodically check the mounting screws for tightness and the wiring for any signs of wear or damage.
• No user-serviceable parts are inside the sealed unit.

8. Fejlfinding

9. Specifikationer

• Modelnummer: 7960B
• Type: Wired Bell Push
• Montering: Overflademonteret
• Slutte: Messing
• Belysning: Yes (Micro LED)
• Strømkilde: Lav voltage (from doorbell transformer)
• Pakkedimensioner: 5.59 x 3.7 x 1.26 tommer
• Varens vægt: 1.44 ounce
• Batterier påkrævet: Ingen

10. Garanti og support

Byron products are manufactured to high standards. For specific warranty details and customer support, please refer to the documentation provided at the time of purchase or visit the official Byron webwebsted. Gem din købsbevis til garantikrav.