1. Introduktion
This manual provides essential information for the safe and efficient operation, setup, and maintenance of your Holzmann TS315VF-2000-230V Table Saw. Please read these instructions thoroughly before assembly, operation, or maintenance to ensure proper use and to prevent injury or damage to the machine. Keep this manual in a safe place for future reference.
The Holzmann TS315VF-2000-230V is a robust table saw designed for precise cutting of various wood materials. It features a powerful 3000W motor, a 315mm main saw blade, and an integrated 90mm scoring saw for chip-free cuts on delicate panels. The machine is equipped with a 2000mm aluminum sliding carriage and a cast iron work table with extensions for handling large workpieces.
2. Sikkerhedsinstruktioner
Overhold altid de generelle sikkerhedsforskrifter, når du arbejder med elværktøj. Manglende overholdelse af disse instruktioner kan resultere i elektrisk stød, brand og/eller alvorlig personskade.
- Personligt beskyttelsesudstyr (PPE): Always wear safety glasses, hearing protection, and a dust mask. Use appropriate gloves when handling blades.
- Arbejdsområde: Keep the work area clean and well-lit. Cluttered or dark areas invite accidents. Ensure adequate space around the machine for safe operation and material handling.
- Elektrisk sikkerhed: Ensure the power supply matches the machine's requirements (230 V, 50 Hz). Do not operate power tools in explosive atmospheres, such as in the presence of flammable liquids, gases, or dust.
- Maskinens tilstand: Before each use, inspect the machine for damage, loose parts, or worn components. Do not operate a damaged machine.
- Klingesikkerhed: Ensure the blade is sharp, clean, and correctly installed. Never operate the saw without the blade guard in place.
- Håndtering af emne: Always use push sticks or push blocks when cutting small workpieces. Never reach over or around the saw blade while it is running.
- Støvsugning: Connect the machine to a dust extraction system to minimize airborne dust and maintain a clear view af skærelinjen.
- Nødstop: Gør dig bekendt med placeringen og betjeningen af nødstopknappen.
- Tag stikket ud før justeringer: Always disconnect the machine from the power supply before making any adjustments, changing blades, or performing maintenance.
3. Komponenter og funktioner
The Holzmann TS315VF-2000-230V Table Saw is equipped with several key components designed for precision and versatility.
- Main Saw Blade (315mm): For primary cutting operations.
- Scoring Saw (90mm): Located in front of the main blade, it scores the material surface to prevent chipping on laminated or veneered panels.
- Blade Height and Tilt Adjustment: Controlled by two independent handwheels for precise angle and depth settings.
- Cast Iron Work Table: Provides a stable and durable surface for cutting.
- Tabeludvidelser: Side and rear extensions increase the working surface for larger materials. A support leg is included for the side extension.
- 2000mm Aluminum Sliding Carriage: Allows for accurate cross-cutting of large panels.
- Carriage Frame with Telescopic Rule and Cut Stop: Facilitates precise measurement and repeatable cuts.
- Rip hegn: Adjustable fence for accurate rip cuts.
- Precision Miter Gauge: For angled cuts on the main table.
- Bladbeskytter: Essential safety component covering the saw blade.
- Dust Extraction Outlet (100mm): For connecting to a dust collection system.
4. Opsætning
Careful assembly and setup are crucial for the performance and safety of your table saw.
- Udpakning og inspektion: Carefully unpack all components. Check for any shipping damage or missing parts against the packing list.
- Basissamling: Assemble the machine base according to the provided diagrams, ensuring all fasteners are securely tightened.
- Tabeludvidelser: Attach the side and rear table extensions to the main cast iron table. Install the support leg for the side extension to ensure stability.
- Sliding Carriage Assembly: Mount the 2000mm aluminum sliding carriage to the machine. Ensure it glides smoothly and is properly aligned. Attach the carriage frame with the telescopic rule and cut stop.
- Montering af knive: Ensure the machine is unplugged. Install the main 315mm carbide blade and the 90mm scoring saw blade. Ensure they are correctly oriented and securely fastened.
- Bladbeskytter: Install the blade guard over the main saw blade. Ensure it moves freely and provides adequate protection.
- Støvsugning: Connect a 100mm dust extraction hose to the machine's outlet.
- Elektrisk tilslutning: Connect the machine to a grounded 230 V, 50 Hz power supply.
- Indledende justeringer: Perform initial checks for blade alignment, fence parallelism, and carriage squareness. Refer to the detailed adjustment section in the full manual for precise calibration.
5. Betjeningsvejledning
Følg disse trin for sikker og effektiv betjening af din bordrundsav.
- Forberedelse:
- Brug alt nødvendigt personligt beskyttelsesudstyr.
- Sørg for, at arbejdsområdet er klart og godt oplyst.
- Verify the blade is sharp, clean, and correctly installed.
- Connect the dust extraction system.
- Justering af bladhøjde: Use the dedicated handwheel to adjust the main blade height. For most cuts, the blade should extend approximately 3-6mm above the workpiece.
- Blade Tilt Adjustment: Use the second handwheel to tilt the blade for angled cuts (0° to 45°). Lock the tilt mechanism securely after adjustment.
- Scoring Saw Adjustment: If using the scoring saw, adjust its height to score the bottom surface of the workpiece just enough to prevent tear-out.
- Rip Cuts (using Rip Fence):
- Set the rip fence to the desired width, ensuring it is parallel to the blade.
- Place the workpiece flat on the table, firmly against the fence.
- Turn on the saw and allow the blades to reach full speed.
- Feed the workpiece slowly and steadily through the blade, keeping it pressed against the fence. Use a push stick for the last portion of the cut.
- Cross Cuts (using Sliding Carriage):
- Position the workpiece on the sliding carriage, using the telescopic rule and cut stop for accurate length. Secure the workpiece with the eccentric clamp om nødvendigt.
- Turn on the saw and allow the blades to reach full speed.
- Push the sliding carriage smoothly and steadily through the blades to make the cut.
- Efter skæring: Turn off the saw and wait for the blades to come to a complete stop before removing cut pieces or clearing sawdust.
6. Vedligeholdelse
Regelmæssig vedligeholdelse sikrer din bordrundsavs lange levetid og sikker drift.
- Daglig rengøring: After each use, unplug the machine and clean all sawdust and debris from the table, blade area, and dust extraction ports.
- Bladinspektion: Regularly inspect saw blades for sharpness, damage, or missing teeth. Replace dull or damaged blades immediately.
- Smøring: Periodically lubricate moving parts such as the blade tilt and height mechanisms, and the sliding carriage rails, according to the manufacturer's recommendations.
- Kontrol af fastgørelseselementer: Routinely check all nuts, bolts, and screws for tightness. Tighten any loose fasteners.
- Elektriske komponenter: Inspect the power cord and plug for damage. Ensure all electrical connections are secure.
- Støvudsugningssystem: Ensure the dust extraction system is functioning effectively and clear of blockages.
- Professionel servicering: For complex repairs or internal component checks, consult a qualified service technician.
7. Fejlfinding
Dette afsnit omhandler almindelige problemer, du kan støde på med din bordrundsav.
| Problem | Mulig årsag | Løsning |
|---|---|---|
| Saven starter ikke | No power supply, emergency stop engaged, faulty switch | Check power connection, reset emergency stop, inspect switch |
| Blade binds or stalls | Dull blade, improper feed rate, misaligned fence, warped workpiece | Replace/sharpen blade, reduce feed rate, check fence alignment, use straight material |
| Overdreven vibration | Loose blade, damaged blade, unbalanced motor, loose fasteners | Check blade tightness, replace damaged blade, inspect motor, tighten fasteners |
| Poor cut quality (tear-out, rough edges) | Dull blade, incorrect blade type for material, scoring saw not adjusted/used | Replace/sharpen blade, use appropriate blade, adjust/use scoring saw |
| Støvopsamling ineffektiv | Clogged hose/port, weak dust collector, improper connection | Clear blockages, check dust collector performance, ensure tight connections |
8. Specifikationer
Detailed technical specifications for the Holzmann TS315VF-2000-230V Table Saw.
| Specifikation | Værdi |
|---|---|
| Model | TS315VF-2000-230V |
| Motor Power S1 (100%) | 3000 W |
| Voltage / Frekvens | 230 V / 50 Hz |
| Main Blade Speed | 4000 rpm |
| Scoring Saw Speed | 5800 rpm |
| Main Blade Diameter / Bore | 315 mm / 30 mm |
| Scoring Saw Diameter / Bore | 90 mm / 20 mm |
| Skærehøjde ved 90° | 100 mm |
| Skærehøjde ved 45° | 80 mm |
| Sliding Carriage Stroke | 2000 mm |
| Rip Capacity against Fence | 1260 mm |
| Støvudsugningsudtag | 100 mm |
| Nettovægt | 270 kg |
| Produktmål (L x B x H) | 82 x 80 x 80 cm (hovedenhed) |
| Inkluderede komponenter | Carbide blade, scoring saw, eccentric clamp, blade guard, precision miter gauge, cross-cut fence, rip fence |
9. Garanti og support
The Holzmann TS315VF-2000-230V Table Saw comes with a 2 års garanti. This warranty covers manufacturing defects but excludes wear parts. For warranty claims, technical support, or spare parts, please contact your authorized Holzmann dealer or the manufacturer directly with your proof of purchase and the machine's model number.
Always refer to the official Holzmann website or your local distributor for the most up-to-date warranty terms and service information.
