Brugermanual til Linear MCT-3 Megacode 3-kanals fjernbetjening

1. Introduktion

This manual provides instructions for the Linear MCT-3 Megacode 3-Channel Remote Control, model DNT00089. This remote is designed for use with Linear's Mega Code series of receivers, commonly found in garage door openers and automatic gate systems. It allows for the control of up to three separate devices.

The Linear MCT-3 remote transmits a unique code for each of its three buttons. This enables control of multiple devices, such as a garage door opener, an access gate, and an additional garage door operator, all from a single remote.

Comparison of Linear DNT00093 and DNT00089 remote controls

Billede 1.1: Comparison showing the Linear DNT00093 (left) and DNT00089 (right) remote controls. The DNT00093 is a replacement for the DNT00089, indicating functional equivalence.

2. Produktfunktioner

Three-Channel Operation: Controls up to three separate Linear Mega Code compatible devices.
Mega Code Technology: Utilizes secure, encrypted radio frequency transmission.
Visor Clip Design: Easily attaches to a vehicle's sun visor for convenient access.
Kompakt og holdbar: Designed for everyday use.
Nem programmering: Simple "Learn" button programming with compatible receivers.

Billede 2.1: Front view of the Linear MCT-3 Megacode 3-Channel Remote Control, showing its three distinct buttons.

3. Opsætning og programmering

To program your Linear MCT-3 remote control, follow these steps. Ensure you are near your garage door opener or gate receiver during this process.

Locate the Receiver's Learn Button: On your garage door opener or gate receiver, find the "Learn" button. The location of this button varies by model, but it is typically on the motor unit itself. Refer to your opener's manual if you cannot locate it.
Aktivér læringstilstand: Press and release the "Learn" button on your receiver. The indicator light on the receiver will typically illuminate or flash, indicating it is in programming mode. You usually have about 30 seconds to complete the next step.
Programmér fjernbetjeningen: While the receiver is in learn mode, press and hold the desired button on your Linear MCT-3 remote control that you wish to use for this device.
Bekræft programmering: Release the remote button once the receiver's indicator light changes (e.g., turns off, flashes rapidly, or the garage door/gate moves slightly). This confirms successful programming.
Test drift: Press the programmed button on your remote control to ensure it activates the garage door or gate.

Note: If you wish to program additional buttons on the remote for other devices, repeat steps 2-5 for each device, selecting a different button on the remote each time.

4. Betjening

Once programmed, operating your Linear MCT-3 remote control is straightforward:

Aktiver enhed: Press the corresponding button on the remote control that has been programmed to your garage door opener or gate.
Rækkevidde: For optimal performance, ensure you are within a reasonable operating range of your receiver. Environmental factors can affect signal range.

5. Maintenance: Battery Replacement

The Linear MCT-3 remote control requires one 9V battery. If the remote's indicator light does not illuminate when a button is pressed, or if the range significantly decreases, the battery may need replacement.

Åbn fjernbetjeningen Casing: Locate the battery compartment cover on the back of the remote. This may require a small screwdriver or prying tool to open carefully.
Fjern det gamle batteri: Carefully remove the old 9V battery from its terminals.
Isæt nyt batteri: Insert a new 9V alkaline battery, ensuring the positive (+) and negative (-) terminals are correctly aligned.
Luk Casing: Sæt dækslet til batterirummet på igen, og sørg for, at det er ordentligt fastgjort.
Prøve: Test the remote's operation with your programmed device.

Bortskaffelse: Please dispose of old batteries responsibly according to local regulations.

6. Fejlfinding

Problem	Mulig årsag	Løsning
Remote does not activate device.	Tæt eller lavt batteri. Fjernbetjeningen er ikke programmeret korrekt. Uden for rækkevidde. Modtagerfejl.	Udskift 9V-batteriet (se afsnit 5). Re-program the remote (refer to Section 3). Flyt dig tættere på modtageren. Check the receiver's power and functionality.
Reduceret rækkevidde.	Lavt batteri. Interference from other radio frequency devices. Forhindringer mellem fjernbetjening og modtager.	Udskift 9V batteriet. Identificer og afbød kilder til interferens. Ensure a clear line of sight if possible.
Indikatorlampen på fjernbetjeningen lyser ikke.	Dødt eller forkert installeret batteri.	Check and replace the 9V battery.

7. Specifikationer

Feature	Detalje
Modelnummer	MCT-3 DNT00089 (Replaced by DNT00093)
Mærke	Lineær
Antal kanaler	3
Forbindelsesteknologi	Radio Frequency (Mega Code)
Kompatible enheder	Linear Mega Code Receivers
Strømkilde	1 x 9V batteri
Produktdimensioner	Cirka 2 x 1 x 1 tommer
Varens vægt	Cirka 0.141 ounce

8. Garanti og support

For specific warranty information and technical support regarding your Linear MCT-3 Megacode 3-Channel Remote Control, please refer to the documentation provided with your purchase or contact Linear directly through their official webwebsted. Gem din købsbevis til garantikrav.

For yderligere hjælp kan du besøge Lineær webwebsted (eksamp(linket, det faktiske link kan variere).

	Lineære MCT-1/MCT-2 MegaCode digitale transmittere: Betjeningsvejledning og programmeringsvejledning Betjeningsvejledning til Linear MCT-1 og MCT-2 MegaCode digitale sendere. Lær om funktioner, programmering, batteriudskiftning, garanti og vigtige FCC-oplysninger for disse sikre trådløse garage- og portfjernbetjeninger.
	Installations- og programmeringsvejledning til lineært NMTK MegaCode trådløst tastatur Detaljerede instruktioner til installation, programmering og betjening af det trådløse Linear NMTK MegaCode-tastatur, inklusive funktioner, batteriudskiftning, vægmontering og garantioplysninger.
	Lineær APEX-controller: Forenklet portbetjening Oplev den lineære APEX-controller, der revolutionerer portbetjening med dens plug-and-play-design, integrerede trådløse modtager og intuitive betjeningselementer for forenklet installation og brug.
	Installations- og programmeringsvejledning til LINEAR DNT00094 NMTK trådløst tastatur Omfattende vejledning til installation og programmering af det trådløse LINEAR DNT00094 NMTK-tastatur til garageport- og portåbnere, der dækker funktioner, betjening, batteriudskiftning og garanti.
	Lineær LDCO801 DC-motor garageportåbner: Husejerens instruktioner og vedligeholdelsesvejledning Omfattende brugervejledning til den lineære LDCO801 DC-motor-garageportåbner. Dækker betjening, opsætning af fjernbetjening, vedligeholdelse, sikkerhedstest, fejlfinding og garantioplysninger.
	Lineær LDCO801 DC-motor garageportåbner Husejervejledning Omfattende brugsanvisning til den lineære LDCO801 garageportåbner med jævnstrømsmotor, der dækker installation, betjening, sikkerhed, vedligeholdelse og fejlfinding. Lær, hvordan du betjener, vedligeholder og fejlfinder din garageportåbner sikkert.

Linear MCT-3 DNT00089