Buderus WK 7300-00.500 Termostathoved Brugermanual

1. Introduktion

This manual provides essential information for the proper installation, operation, and maintenance of your Buderus WK 7300-00.500 Thermostatic Head. Please read these instructions carefully before installation and retain them for future reference. Correct use ensures optimal performance and longevity of the product.

2. Produktet er slutview

The Buderus WK 7300-00.500 is an angled thermostatic head designed for precise temperature control in rooms equipped with radiators. It features a liquid-filled sensor for stable and accurate regulation of room temperature by controlling the flow of hot water through the radiator.

Nøglefunktioner:

• Angled Design: Optimized for mounting on radiators with an M30 x 1.5 threaded connection.
• Integreret sensor: Ensures accurate temperature detection and control.
• Vendbar montering: Can be installed on either the left or right side of the radiator valve.
• Liquid-Filled Thermostat: Provides stable and responsive control behavior.
• White Scale Cover: Clear and easy-to-read temperature settings.

3. Opsætning og installation

Sikkerhed først: Before beginning installation, ensure the heating system is depressurized and cooled down to prevent injury from hot water or steam. If you are unsure about any steps, consult a qualified heating technician.

Installationstrin:

1. Prepare the Radiator Valve: Ensure the existing thermostatic valve body on your radiator has an M30 x 1.5 threaded connection.
2. Fjern gammelt hoved (hvis relevant): If replacing an old thermostatic head, carefully unscrew it from the valve body.
3. Position the Thermostatic Head: Place the Buderus WK 7300-00.500 onto the valve body. The head is reversible, allowing for left or right mounting to suit your radiator's orientation.
4. Fastgør hovedet: Hand-tighten the threaded ring of the thermostatic head onto the M30 x 1.5 connection of the valve body until it is firm. Do not overtighten.
5. Tjek for stabilitet: Ensure the head is securely attached and does not wobble.

4. Betjeningsvejledning

The Buderus WK 7300-00.500 Thermostatic Head allows you to set your desired room temperature by rotating the control knob. The scale is typically marked with numbers and symbols:

• Snowflake Symbol (❄): Frost protection setting. This setting prevents the room temperature from dropping below approximately 6°C (43°F), protecting pipes from freezing.
• Tal (1-5): These numbers correspond to approximate room temperatures. Each increment typically represents a change of about 4°C (7°F).
• Indstilling 1: Cirka 12°C (54°F)
• Indstilling 2: Cirka 16°C (61°F)
• Indstilling 3: Approximately 20°C (68°F) - Recommended comfort setting
• Indstilling 4: Cirka 24°C (75°F)
• Indstilling 5: Maximum heat, approximately 28°C (82°F)
• Sun Symbol (☀): Often indicates a higher comfort setting, typically around 20-21°C (68-70°F), similar to setting 3.

To adjust the temperature, simply rotate the control knob until the desired number or symbol aligns with the indicator mark on the head.

5. Vedligeholdelse

The Buderus WK 7300-00.500 Thermostatic Head requires minimal maintenance to ensure continued efficient operation.

• Rensning: Tør ydersiden af ​​termostathovedet af med en blød, tør klud.amp klud. Brug ikke slibende rengøringsmidler eller opløsningsmidler, da disse kan beskadige overfladen.
• Funktionskontrol: Periodically check that the control knob turns smoothly and that the radiator heats up and cools down as expected when adjusting the setting.
• Undgå forhindringer: Ensure that curtains, furniture, or other objects do not obstruct the thermostatic head, as this can interfere with its ability to accurately sense room temperature.

6. Fejlfinding

If you experience issues with your thermostatic head, consider the following common problems and solutions:

• Radiatoren varmer ikke op:
  • Sørg for, at termostathovedet er indstillet til en temperatur, der er højere end den aktuelle rumtemperatur.
  • Check if the valve pin is stuck. Remove the thermostatic head and gently press the pin in the valve body. It should move freely. If stuck, it may need lubrication or professional attention.
  • Verify that the central heating system is operational and that other radiators are heating.
• Radiator Always Hot (even on low setting):
  • Ensure the thermostatic head is correctly installed and tightened.
  • The valve pin might be stuck in the open position. Try the method described above to free it.
  • The thermostatic head might be faulty and require replacement.
• Inconsistent Room Temperature:
  • Check for drafts or obstructions around the thermostatic head that could affect its temperature sensing.
  • Ensure the heating system is balanced.

If these steps do not resolve the issue, contact a qualified heating technician.

7. Specifikationer

8. Garanti og support

This Buderus product is covered by the manufacturer's standard warranty. For specific warranty terms and conditions, please refer to the documentation provided with your purchase or contact Buderus customer support directly. If you require technical assistance or have questions not covered in this manual, please reach out to your retailer or a certified Buderus service partner.