1. Introduktion
This manual provides essential instructions for the safe and efficient installation, operation, and maintenance of your Advance LED Driver. Please read this manual thoroughly before installation and retain it for future reference.
2. Sikkerhedsoplysninger
ADVARSEL: Risk of electric shock. Installation should be performed by a qualified electrician in accordance with all national and local electrical codes.
- Afbryd strømmen før installation eller servicering.
- Sørg for korrekt jording for at forhindre elektrisk stød.
- Do not exceed the specified input and output voltage/nuværende vurderinger.
- This device is designed for specific LED loads. Do not use with other types of lighting.
- Operate within the specified environmental conditions (temperature, humidity).
3. Produktet er slutview
The Advance LED Driver is a high-performance power supply designed for LED lighting applications. It provides a stable and efficient power source for compatible LED fixtures.
3.1 Nøglefunktioner
- Wattage: 150 Watt
- Output Current: 700mA (non-adjustable)
- Udgang Voltage Område: 60-210V
- Input bindtage: 120-277V
- Dimming: 0-10V Isolated dimming
- Weather Rating: UL Dry & Damp location rated, IP66
3.2 Produktbillede
4. Opsætning og installation
Before beginning installation, ensure all power is disconnected at the circuit breaker. Refer to local and national electrical codes for proper wiring practices.
4.1 Wiring Diagram (Refer to Product Label)
The product label on the LED driver includes a wiring diagram. Typically, connections involve:
- Indgang (AC): Connect the AC input wires (Line, Neutral, Ground) from the power source to the corresponding input terminals on the driver.
- Udgang (DC): Connect the DC output wires (Positive, Negative) from the driver to the LED fixture. Ensure correct polarity.
- Dimming (0-10V): If using dimming functionality, connect the 0-10V dimming control wires to the designated dimming terminals on the driver.
Note: The output current is fixed at 700mA and is not adjustable.
4.2 Montering
Mount the driver securely using appropriate fasteners. Ensure adequate ventilation around the driver to prevent overheating. The driver is rated for UL Dry & Damp locations and IP66, indicating protection against dust and powerful water jets.
5. Betjeningsvejledning
Once properly installed and wired, restore power to the circuit. The LED driver will automatically power the connected LED fixture.
5.1 Dæmpningsfunktionalitet
This driver supports 0-10V isolated dimming. Connect a compatible 0-10V dimmer to the dimming terminals. Adjusting the dimmer will control the light output of the connected LED fixture.
6. Vedligeholdelse
The Advance LED Driver is designed for long-term, reliable operation with minimal maintenance.
- Periodically inspect the driver and wiring for any signs of damage or wear.
- Ensure ventilation openings (if any) are clear of dust and debris.
- Clean the exterior with a soft, dry cloth if necessary. Do not use harsh chemicals or abrasive cleaners.
- If any issues arise, refer to the troubleshooting section or contact qualified personnel.
7. Fejlfinding
If the LED fixture is not operating as expected, perform the following checks:
| Problem | Mulig årsag | Løsning |
|---|---|---|
| LED'er lyser ikke | No power to the driver; incorrect wiring; faulty LED fixture. | Check circuit breaker and power connections. Verify input and output wiring. Test LED fixture with a known good driver. |
| LED'er flimrer eller dæmpes ujævnt | Loose connections; incompatible dimmer; faulty driver. | Inspect all wiring connections. Ensure dimmer is 0-10V compatible. Replace driver if necessary. |
| Driver is hot to the touch | Insufficient ventilation; overloaded driver. | Ensure adequate airflow around the driver. Verify the connected LED load does not exceed the driver's wattage vurdering. |
8. Specifikationer
| Elektriske specifikationer | |
|---|---|
| Input bindtage | 120-277V AC |
| Udgang VoltagRækkevidde | 60-210V DC |
| Udgangsstrøm | 700mA (Fixed) |
| Wattage | 150 watt |
| Dæmpning | 0-10V Isolated |
| Current Rating (Input) | 5 Amps |
| Physical & Environmental Specifications | |
| Dimensioner (L x B x H) | 8.38 cm x 2.35 cm x 1.47 cm |
| Vægt | 0.01 ounce (Note: Please verify actual product weight as this value may be a data entry anomaly.) |
| Vejrbedømmelse | UL Dry & Damp location rated, IP66 |
| Fabrikant | Forskud |
9. Garanti og support
For warranty information or technical support, please refer to the documentation provided with your purchase or contact Advance customer service. Keep your purchase receipt for warranty claims.
