1. Introduktion
This manual provides instructions for the installation, operation, and maintenance of the ICM Controls Fixed 60 Degrees F Thermostat. This low voltage thermostat is designed for use with 2-wire HVAC systems to maintain a fixed temperature of 60 degrees Fahrenheit.
The ICM Controls Fixed 60 Degrees F Thermostat is a non-programmable device intended for applications where a constant temperature setting is required, such as in unoccupied spaces or for freeze protection.
2. Sikkerhedsoplysninger
ADVARSEL: Fare for elektrisk stød
- Always disconnect power to the HVAC system at the main service panel before installing or servicing this thermostat. Failure to do so can result in electrical shock, property damage, or death.
- Installationen skal udføres af en kvalificeret tekniker.
- Sørg for, at alle ledningsforbindelser er sikre og overholder lokale el-forskrifter.
Læs alle instruktioner omhyggeligt, inden du fortsætter med installation eller drift.
3. Pakkens indhold
Kontroller, at alle komponenter er til stede, før installationen påbegyndes:
- ICM Controls Fixed 60 Degrees F Thermostat
- Integrated 6-inch wire leads
4. Installation og opsætning
4.1 Monteringssted
Vælg et monteringssted, der er:
- On an interior wall, approximately 5 feet (1.5 meters) above the floor.
- Away from direct sunlight, drafts, or heat sources (e.g., lamps, appliances, fireplaces).
- Away from areas with poor air circulation.
4.2 Ledningsinstruktioner
- Afbryd strømmen: Turn off power to the HVAC system at the circuit breaker or fuse box.
- Identificér ledninger: This thermostat is designed for 2-wire low voltage HVAC systems (18VAC to 30VAC). Typically, these systems use R (power) and W (heat call) wires. Consult your HVAC system's manual if unsure.
- Tilslut termostat: Connect the two wire leads from the ICM Controls thermostat to the corresponding R and W terminals of your HVAC system's control wiring. Ensure connections are secure.
- Monter termostat: Secure the thermostat to the wall using appropriate fasteners. This unit is designed for surface mounting.
- Gendan strøm: Once wiring is complete and secure, restore power to the HVAC system.
The thermostat will immediately begin sensing the ambient temperature and control the heating system to maintain 60 degrees F.
5. Betjening
The ICM Controls Fixed 60 Degrees F Thermostat is a non-adjustable, single-setpoint device. It is designed to activate your heating system when the ambient temperature falls below 60 degrees Fahrenheit and deactivate it when the temperature reaches or exceeds 60 degrees Fahrenheit.
There are no user-adjustable settings, buttons, or displays on this thermostat. Its operation is fully automatic once correctly installed and powered.
6. Vedligeholdelse
This thermostat requires minimal maintenance. Follow these guidelines:
- Rensning: Periodically wipe the exterior of the thermostat with a soft, dry cloth. Do not use liquid cleaners or solvents.
- Luftstrøm: Ensure that the thermostat is not obstructed by furniture, curtains, or other objects that could impede proper air circulation around the sensor.
- Årlig kontrol: It is recommended to have your HVAC system and thermostat checked annually by a qualified technician to ensure optimal performance.
7. Fejlfinding
If your heating system is not operating as expected, consider the following:
| Problem | Mulig årsag | Løsning |
|---|---|---|
| Varmesystemet tænder ikke. | No power to the thermostat or HVAC system. | Kontroller afbryderen/sikringen. Sørg for, at strømmen er genoprettet. |
| Forkert ledningsføring. | Verify wiring connections (R and W) are secure and correct. Refer to Section 4.2. | |
| Ambient temperature is above 60°F. | The thermostat will only activate heating when the temperature drops below 60°F. This is normal operation. | |
| Heating system running constantly. | Ambient temperature is consistently below 60°F. | This is normal operation if the space requires continuous heating to maintain 60°F. |
| Termostat fejlfunktion. | If the temperature is above 60°F and the heating system is still running, disconnect power and contact a qualified technician or ICM Controls support. |
For issues not listed here, or if troubleshooting steps do not resolve the problem, contact ICM Controls customer support.
8. Specifikationer
| Feature | Detalje |
|---|---|
| Mærke | ICM-kontroller |
| Modelnummer | 7431990920987 |
| Kontrolområde | Fixed 60 Degrees F |
| Voltage | 18VAC til 30VAC |
| Systemskift | Ingen |
| Ventilatorskift | Ingen |
| Automatisk skift | Ingen |
| Dual Transformer Compatible | Ingen |
| Power metode | Hardwired |
| 750mV Compatible | Ingen |
| Monteringstype | Overflademontering |
| Dimensioner (højde x bredde x dybde) | 2 In. x 3/8 In. x 3/8 In. (Approximate, based on description) |
| Inkluderede komponenter | 6" Wire Leads |
| Varens vægt | 16 ounce (1 pund) |
9. Garanti og support
For warranty information, please refer to the documentation provided with your purchase or visit the official ICM Controls website. ICM Controls products are designed for reliability and performance.
If you require technical assistance or have questions regarding your ICM Controls Fixed 60 Degrees F Thermostat, please contact ICM Controls customer support through their official channels. Have your model number (7431990920987) ready when contacting support.
ICM-kontroller Webwebsted: www.icmcontrols.com
