Indledning
This manual provides essential information for the installation, operation, and maintenance of your Amerec KT60/K60 Digital Controls. These dual 3-button digital controls are designed to display temperature and time, offering precise management of your steam environment. The system includes both an internal control (KT60 with integral temperature sensor) and an external control (K60), along with necessary cables and a Comfort Flo steam head.
Opsætning og installation
The Amerec KT60/K60 Digital Control system is designed for integration with Amerec steam generators. Proper installation is crucial for optimal performance and safety. It is highly recommended that installation be performed by a qualified electrician or service technician.
- De KT60 control features an integral temperature sensor and is designed to be mounted inside the steam room.
- De K60 control is intended for mounting outside the steam room.
- Ensure all cables are securely connected between the controls and the steam generator as per the detailed wiring diagrams provided in the full installation manual.
- The Comfort Flo steam head should be installed according to the separate instructions provided with the steam generator.
Image: The Amerec KT60/K60 Digital Controls, showing the polished brass finish and the digital display with "114" degrees, along with "TIME", "ON/OFF", and "TEMP" buttons. The image displays the front and side views of the control units.
Betjeningsvejledning
The KT60/K60 controls provide intuitive operation for your steam bath experience.
- Tænd/sluk: Tryk på ON/OFF button to activate or deactivate the steam generator. The digital display will illuminate when the unit is active.
- Justering af temperatur: Tryk på TEMP button. The display will show the current set temperature. Use the up/down arrows (if present, or repeated presses of TEMP/TIME buttons in some models) to adjust the temperature up to 125° F. The display will revert to showing the actual room temperature once set.
- Justeringstid: Tryk på TID button. The display will show the current set duration. Use the up/down arrows (or repeated presses) to adjust the steam session duration up to 60 minutes. The display will show the remaining time during operation.
- Vise: The digital display continuously shows the current temperature or remaining time, depending on the mode selected or during idle operation.
Opretholdelse
Regular maintenance ensures the longevity and optimal performance of your Amerec digital controls.
- Rensning: To clean the polished brass finish, use a soft, damp klud. Undgå slibende rengøringsmidler, opløsningsmidler eller barske kemikalier, da disse kan beskadige overfladen og de elektroniske komponenter.
- Inspektion: Periodically inspect the control units and cables for any signs of wear or damage. If any damage is observed, contact a qualified technician for repair or replacement.
Fejlfinding
If you encounter issues with your Amerec KT60/K60 Digital Controls, consider the following basic troubleshooting steps:
- Ingen strøm/skærm slukket:
- Check the main power supply to the steam generator.
- Ensure all control cables are securely connected to both the controls and the generator.
- Verify that the circuit breaker for the steam unit has not tripped.
- Forkert temperaturaflæsning:
- Ensure the KT60 control (with the integral sensor) is properly installed inside the steam room and not obstructed.
- Avoid placing the sensor near direct steam output or drafts that could affect readings.
- Betjeningselementer reagerer ikke:
- Try cycling the power to the steam generator (turn off at the breaker for a few minutes, then turn back on).
- If issues persist, consult the comprehensive troubleshooting guide in the full product manual or contact Amerec customer support.
Specifikationer
| Feature | Detalje |
|---|---|
| Fabrikant | Amerec |
| Varenummer | DKT60/K60-PB |
| Varens vægt | 3.75 pund |
| Pakkedimensioner | 11.8 x 9.1 x 3.2 tommer |
| Varemodelnummer | DKT60/K60-PB |
| Farve | Poleret messing |
| Stil | Moderne |
| Vare Pakke Antal | 1 |
| Adjustable Time Duration | Op til 60 minutter |
| Justerbar temperatur | Up to 125° F |
Garantioplysninger
The Amerec KT60/K60 Digital Controls come with a limited warranty:
- Dele: Fem (5) år
- Arbejdskraft: To (2) år
Please retain your proof of purchase for warranty claims. For full warranty terms and conditions, refer to the documentation included with your product or visit the official Amerec webwebsted.
Kundesupport
For technical assistance, service, or to order replacement parts, please contact Amerec customer support or an authorized service center. Contact information can typically be found on the manufacturer's webwebstedet eller i den originale produktemballage.
When contacting support, please have your product model number (DKT60/K60-PB) and serial number (if applicable) ready.
