Sharp Cyclone støvsuger EC-CT12-C brugermanual

1. Produktet er slutview

The Sharp EC-CT12-C is a bagless cyclone vacuum cleaner designed for efficient cleaning of various floor types. It features a powerful centrifugal cyclone system for dust separation and a turbine head for effective debris collection.

Figure 1: Assembled Sharp EC-CT12-C Cyclone Vacuum Cleaner.

2. Sikkerhedsinstruktioner

Before operating the vacuum cleaner, please read and understand all safety instructions to prevent electric shock, fire, or injury.

• Sørg for, at strømforsyningen voltage stemmer overens med den klassificering, der er angivet på støvsugeren.
• Brug ikke støvsugeren på våde overflader eller til at opsuge væsker.
• Saml ikke brændende eller rygende genstande op, såsom cigaretter, tændstikker eller varm aske.
• Hold hår, løstsiddende tøj, fingre og alle dele af kroppen væk fra åbninger og bevægelige dele.
• Unplug the appliance from the electrical outlet before cleaning or performing maintenance.
• Brug ikke støvsugeren med en beskadiget ledning eller stik.

3. Opsætning og montering

The Sharp EC-CT12-C requires minor assembly before first use. Follow these steps:

1. Fastgør slangen: Insert the flexible hose into the suction port on the main unit until it clicks securely into place.
2. Connect the Extension Wand: Attach the extension wand to the end of the flexible hose.
3. Install the Floor Head: Connect the turbine floor head to the end of the extension wand. Ensure it is firmly attached.

Figure 2: Main vacuum unit with detached turbine floor head, ready for assembly.

Once assembled, extend the power cord and plug it into a suitable electrical outlet.

4. Betjeningsvejledning

To operate your Sharp EC-CT12-C vacuum cleaner:

1. Tænd/sluk: Press the power button located on the main unit or handle to turn the vacuum cleaner on or off.
2. Juster sugestyrke: The vacuum cleaner features 3 power levels. Adjust the suction power as needed for different cleaning tasks and floor types. A lower setting is suitable for delicate surfaces, while a higher setting provides maximum suction for heavily soiled areas.
3. Using the Turbine Head: The turbine head utilizes wind power to rotate its brush, effectively collecting debris from carpets and hard floors. For certain floor conditions, the brush rotation may temporarily stop. The turbine head also includes a wipe function suitable for various floor types, including tatami mats.
4. Eco-Cleaning Mode: This mode adjusts power consumption based on the cleaning operation and floor type, optimizing energy use.
5. Brug af vedhæftede filer: For specific cleaning tasks, detach the floor head and attach appropriate accessories (not specified in provided data, but generally include crevice tools, upholstery brushes).

5. Vedligeholdelse

Regelmæssig vedligeholdelse sikrer optimal ydeevne og forlænger din støvsugers levetid.

5.1 Tømning af støvbeholderen

The EC-CT12-C features a one-touch detachable dust cup for easy emptying.

1. Sørg for, at støvsugeren er taget ud af stikkontakten.
2. Press the release button to detach the dust cup from the main unit.
3. Hold the dust cup over a trash receptacle and open the bottom lid to empty collected dust and debris.
4. Close the lid and reattach the dust cup to the main unit until it clicks securely.

Figure 3: Detached dust cup from the main vacuum unit, showing the cyclone mechanism.

5.2 Rengøring af HEPA-filteret

The HEPA clean filter effectively captures fine dust. It is designed for easy cleaning.

1. Træk støvsugeren ud.
2. Fjern støvbeholderen som beskrevet ovenfor.
3. Locate the HEPA filter within the dust cup assembly.
4. Turn the knob to easily clean the filter. Refer to the markings on the filter for specific cleaning instructions (e.g., tapping out dust, rinsing if applicable and allowing to dry completely).
5. Sørg for, at filteret er helt tørt, før det samles igen.

5.3 Rengøring af børstevalsen

Periodically inspect and clean the brush roll in the turbine head to remove tangled hair or debris.

1. Træk støvsugeren ud.
2. Detach the turbine floor head from the extension wand.
3. Turn the floor head over to access the brush roll.
4. Use scissors or a brush to carefully cut and remove any tangled hair or fibers from the brush roll.
5. Ensure the brush roll spins freely before reattaching the floor head.

Figur 4: Underside view of the turbine floor head, showing the brush roll for cleaning.

6. Fejlfinding

If you encounter issues with your Sharp EC-CT12-C, refer to the following common troubleshooting steps:

• Ingen strøm:
  • Kontroller, om netledningen er sat ordentligt i en fungerende stikkontakt.
  • Sørg for, at tænd/sluk-knappen er trykket ned.
  • Tjek din husstands afbryder.
• Tab af sugeevne:
  • Empty the dust cup if it is full.
  • Clean the HEPA filter as described in Section 5.2.
  • Check the hose, wand, and floor head for blockages.
  • Ensure all connections (hose, wand, floor head) are secure.
• Usædvanlig støj:
  • Turn off and unplug the vacuum. Inspect the brush roll for obstructions.
  • Check for any foreign objects lodged in the hose or floor head.
• Brush Roll Not Rotating:
  • Clean the brush roll as described in Section 5.3.
  • Ensure the floor head is properly attached.
  • Note that the turbine head's brush rotation may stop depending on the floor surface.

If the problem persists after performing these checks, contact Sharp customer support.

7. Specifikationer

Figure 5: Approximate size comparison of the vacuum cleaner.

8. Garanti og support

Garantioplysninger: This product is covered by a manufacturer's warranty. Please refer to the warranty card included with your purchase for specific terms, conditions, and duration. Retain your proof of purchase for warranty claims.

Kundesupport: For technical assistance, spare parts, or warranty service, please contact Sharp customer support. You can find contact information on the official Sharp webwebstedet eller via den dokumentation, der følger med dit produkt.

Visit the official Sharp Store for more information: Sharp Store på Amazon