Skil 9425 ME vinkelsliber brugsanvisning

1. Sikkerhedsinstruktioner

Always observe the following basic safety precautions when using the Skil 9425 ME Angle Grinder to reduce the risk of electric shock, fire, and serious injury.

1.1 Generelle sikkerhedsadvarsler for elværktøj

• Sikkerhed på arbejdsområdet: Hold arbejdsområdet rent og godt oplyst. Rodede eller mørke områder indbyder til ulykker. Brug ikke elværktøj i eksplosive atmosfærer, f.eks. i nærheden af ​​brandfarlige væsker, gasser eller støv.
• Elektrisk sikkerhed: Elværktøjsstik skal passe til stikkontakten. Modificer aldrig stikket på nogen måde. Brug ikke adapterstik med jordforbundne elværktøjer. Undgå kropskontakt med jordforbundne overflader.
• Personlig sikkerhed: Brug altid øjenbeskyttelse. Brug personlige værnemidler såsom støvmasker, skridsikre sikkerhedssko, sikkerhedshjelme eller høreværn, når det er relevant. Vær opmærksom, hold øje med, hvad du laver, og brug sund fornuft, når du bruger et elværktøj.
• Brug og vedligeholdelse af elværktøj: Tving ikke elværktøjet. Brug det korrekte elværktøj til din anvendelse. Tag stikket ud af strømkilden, før du foretager justeringer, skifter tilbehør eller opbevarer elværktøj.

1.2 Specifikke sikkerhedsadvarsler for vinkelslibere

• Dette elværktøj er beregnet til at fungere som slibemaskine, slibemaskine, stålbørste eller skæreværktøj. Læs alle sikkerhedsadvarsler, instruktioner, illustrationer og specifikationer, der følger med dette elværktøj.
• Always use the correct type of grinding disc for the material and application. Ensure the disc is securely mounted before operation.
• Always use the protective guard. The guard must be securely attached and positioned for maximum safety, covering the largest possible part of the wheel.
• Hold værktøjet fast med begge hænder. Tab af kontrol kan resultere i personskade.
• Never place the tool down until the accessory has come to a complete stop.

2. Produktet er slutview

The Skil 9425 ME is a robust angle grinder designed for demanding grinding and cutting tasks. It features a powerful 750 Watt motor, ball bearings, and angle gear for increased service life, and a lightweight, slim design for comfortable handling.

Figure 1: Skil 9425 ME Angle Grinder. This image shows the complete angle grinder with the main body, side handle, and protective guard in place, ready for operation.

3. Opsætning

3.1 Montering af sidehåndtaget

The side handle can be screwed into either the left or right side of the gear housing, depending on your preference and the application. Always ensure the side handle is securely tightened before operating the tool.

Figure 2: Side Handle. This image displays the textured side handle, which provides additional grip and control during operation.

3.2 Justering af beskyttelsesskærmen

The protective guard is essential for user safety. It can be easily adjusted without tools to suit the working angle and protect against sparks and debris.

1. Løsn clamping lever on the protective guard.
2. Rotate the guard to the desired position, ensuring it provides maximum protection.
3. Spænd clamping lever firmly to secure the guard in place.

Figure 3: Protective Guard. This image shows the metal protective guard, designed to shield the user from sparks and debris during grinding or cutting operations.

3.3 Montering/udskiftning af slibeskive

Always ensure the tool is unplugged from the power source before changing discs.

1. Tryk på spindellåseknappen for at forhindre spindlen i at rotere.
2. Use the double-hole wrench to loosen the clamping nut by turning it counter-clockwise.
3. Remove the old grinding disc and the clamping møtrik.
4. Place the new grinding disc onto the mounting flange, ensuring it sits correctly.
5. Skru clamping nut back on and tighten it firmly with the double-hole wrench while holding the spindle lock button.

Figure 4: Disc and Guard Close-up. This image provides a detailed view of the grinding disc mounted on the tool, with the protective guard positioned above it.

4. Betjening

4.1 Tænd/sluk

• Sådan tænder du: Press the ON/OFF switch. For continuous operation, press the switch and then slide it forward until it locks.
• Sådan slukker du: For continuous operation, press the rear part of the ON/OFF switch. For momentary operation, simply release the switch.

4.2 Slibeteknikker

• Hold altid vinkelsliberen fast med begge hænder.
• Brug moderat tryk. For højt tryk kan reducere skivens levetid og motorens effektivitet.
• Maintain a consistent angle between the disc and the workpiece, typically 15-30 degrees for grinding.
• Bevæg værktøjet jævnt hen over emnet for at sikre jævn materialefjernelse.

Figure 5: Angle Grinder with Handle. This image shows the angle grinder from a front perspective, highlighting the main body and the attached side handle, illustrating how the tool is held during use.

5. Vedligeholdelse

Regular maintenance ensures the longevity and safe operation of your Skil 9425 ME Angle Grinder.

5.1 Rengøring

• Tag altid stikket ud af stikkontakten før rengøring.
• Keep the ventilation slots clean to prevent motor overheating. Use a soft brush or compressed air to remove dust and debris.
• Tør værktøjshuset af med snavsamp klæde. Brug ikke skrappe rengøringsmidler eller opløsningsmidler.

5.2 Udskiftning af kulbørste

The carbon brushes wear down over time. If the motor performance decreases significantly or sparks become excessive, the carbon brushes may need replacement. This procedure should ideally be performed by a qualified service technician.

5.3 Opbevaring

Store the angle grinder in a dry, secure place, out of reach of children. Ensure the power cord is neatly coiled and not kinked.

6. Fejlfinding

Dette afsnit omhandler almindelige problemer, du kan støde på med din vinkelsliber.

• Værktøjet starter ikke:
  • Kontroller, om netledningen er sat ordentligt i en fungerende stikkontakt.
  • Undersøg netledningen for skader.
  • Ensure the ON/OFF switch is fully engaged.
  • If the issue persists, carbon brushes might be worn (refer to Section 5.2).
• Overdreven vibration:
  • Kontroller om slibeskiven er korrekt monteret og spændt.
  • Inspect the disc for damage or imbalance. Replace if necessary.
• Reduced performance/Overheating:
  • Ensure ventilation slots are clear of dust and debris.
  • Undgå at påføre for stort tryk under drift.
  • Lad værktøjet køle af, hvis det føles for varmt.

7. Specifikationer

8. Garanti og support

This Skil power tool is manufactured to high-quality standards. For information regarding warranty terms and conditions, please refer to the warranty card included with your product or visit the official Skil webwebsted.

For technical support, spare parts, or service inquiries, please contact your local authorized Skil service center. Always provide the model number (F0159425ME) and serial number (if applicable) when seeking support.