Progressive Industries EMS-HW50C 50 Amp Brugsanvisning til overspændingsbeskytter til campingvogne

1. Introduktion

The Progressive Industries EMS-HW50C is a 50 Amp Heavy Duty RV Surge Protector equipped with an advanced Electrical Management System (EMS). This unit is designed to provide top-tier protection for your RV's sensitive electronics and appliances against various power fluctuations and surges encountered at campgrounds or other power sources. It actively monitors incoming power and disconnects the RV if hazardous conditions are detected, ensuring the longevity and safety of your electrical equipment.

2. Sikkerhedsoplysninger

ADVARSEL: To reduce the risk of electrical shock, always open or disconnect the circuit from the power-distribution system (or system) of the building before installing or servicing current-sensing transformers. Installation should only be performed by a qualified electrician or RV technician.

Dette produkt kan udsætte dig for kemikalier, herunder bly, som staten Californien har kendskab til for at forårsage kræft og fosterskader eller andre reproduktionsskader. For mere information, gå til www.P65Warnings.ca.gov.

• Always ensure the power source is disconnected before handling the unit or any associated wiring.
• Brug ikke enheden, hvis den ser ud til at være beskadiget.
• Hold enheden væk fra vand og ekstreme temperaturer.
• Ensure proper grounding for safe operation.

3. Opsætning og installation

The EMS-HW50C is a hardwired unit designed for permanent installation within your RV's electrical system. It should be installed after the transfer switch but before the main electrical panel.

Figure 1: Progressive Industries EMS-HW50C main unit with remote display.

Installationstrin:

1. Strømafbrydelse: Ensure all power to the RV, including shore power and generator, is completely disconnected.
2. Montering: Select a suitable, dry location within your RV for mounting the main EMS unit. Ensure adequate ventilation and access for wiring.
3. Ledningsforbindelser: Connect the incoming power lines (Line/Input) to the designated terminals on the EMS unit. Connect the outgoing power lines (Load/Output) from the EMS unit to your RV's main electrical panel. Ensure all connections are secure and follow local electrical codes.
4. Jording: Securely connect the ground wires to the designated ground screws on the unit.
5. Remote Display Installation: The remote display provides real-time status and error codes. Mount the remote display in a convenient, visible location inside your RV. Connect the remote display to the main EMS unit using the provided data cable.

Figur 2: Intern view of the EMS-HW50C, illustrating wiring components.

After installation, ensure all covers are securely fastened to protect internal components.

4. Betjening

Once installed and powered, the EMS-HW50C continuously monitors the incoming electrical power. The integrated display on the unit and the remote display will show real-time voltage og amperage readings for both lines, as well as frequency and any detected error codes.

Upon initial power-up or after a power interruption, the unit typically undergoes a 30-second delay. This delay allows the EMS to perform a comprehensive diagnostic check of the power source, ensuring it is clean and safe before allowing power to pass through to your RV.

Figure 3: The EMS-HW50C display showing operational status or error codes.

The display cycles through various readings:

• Linje 1 Voltage & Ampalder: Viser voltage and current draw on the first power line.
• Linje 2 Voltage & Ampalder: Viser voltage and current draw on the second power line.
• Frekvens: Shows the frequency of the incoming power (should typically be 60 Hz).
• Fejlkoder: If a fault is detected, an error code (e.g., E1, E2) will be displayed. Refer to the Troubleshooting section for a full list of codes and their meanings.

5. Vedligeholdelse

The EMS-HW50C is designed for durability and minimal maintenance. However, periodic inspection is recommended to ensure optimal performance and safety:

• Visuel inspektion: Regularly check the unit and its wiring for any signs of physical damage, corrosion, or loose connections.
• Renhed: Keep the unit free from dust, dirt, and debris. Use a soft, dry cloth for cleaning. Do not use abrasive cleaners or solvents.
• Funktionstjek: Periodically observe the display during operation to ensure it is cycling through readings correctly and not displaying persistent error codes.

Hvis der observeres problemer, skal du se afsnittet Fejlfinding eller kontakte kundesupport.

6. Fejlfinding

The EMS-HW50C is equipped with advanced fault detection capabilities. If an electrical issue is detected, the unit will display an error code (E0-E10 or PE) and may cut power to your RV to prevent damage. Refer to the table below for common error codes and their meanings:

Figure 4: Error codes displayed on the EMS-HW50C unit.

For further assistance, consult the official Fejlfindingsvejledning (PDF) or contact Progressive Industries customer support.

7. Specifikationer

• Model: EMS-HW50C
• Ampalder: 50 Amps
• Voltage: 120-240 volt
• Wattage: 12,000 watt
• Overspændingsbeskyttelse: 3,580 Joule
• Varens vægt: 2.49 pund
• Produktdimensioner: 10.2 x 5.6 x 0.1 tommer
• Særlige funktioner: Electrical Management System (EMS), Advanced Fault Detection, A/C Frequency Protection, Thermal Protection, Integrated Display with LED Indicators.
• Farve: Sort
• Fabrikant: Progressive industrier
• Oprindelsesland: Fremstillet i USA

8. Garanti og support

Progressive Industries is known for its excellent customer support and offers a lifetime warranty on its EMS products. For any questions, technical assistance, or warranty claims, please contact Progressive Industries directly.

Yderligere ressourcer:

• Officiel brugermanual (PDF)
• Fejlfindingsvejledning (PDF)