Waring Commercial WSB60ST Immersion Blender Shaft

1. Introduktion

This manual provides essential instructions for the proper use, maintenance, and care of your Waring Commercial WSB60ST 16-inch Stainless Steel Immersion Blender Shaft. This shaft is designed as an interchangeable accessory for specific Waring Big Stix immersion blender power units, offering versatility and durability for commercial kitchen environments.

Image 1.1: The Waring Commercial WSB60ST 16-inch Stainless Steel Immersion Blender Shaft. This component is designed for attachment to compatible Waring Big Stix power units.

2. Sikkerhedsoplysninger

Always observe basic safety precautions when using electrical appliances, especially in a commercial setting. This shaft is an accessory and must be used with a compatible Waring Big Stix immersion blender power unit.

• Læs alle instruktioner: Before using the immersion blender shaft, read all operating instructions for the compatible power unit.
• Korrekt vedhæftning: Ensure the shaft is securely attached to the power unit before operation.
• Klingesikkerhed: The cutting blade is sharp. Handle with care to prevent injury.
• Væskeniveau: Do not immerse the power unit in liquid. Only the shaft is designed for immersion.
• Overvågning: Tæt opsyn er nødvendigt, når et apparat bruges af eller i nærheden af ​​børn.
• Opretholdelse: Perform maintenance and cleaning only when the power unit is unplugged.

3. Pakkens indhold

Kontroller, at alle komponenter er til stede ved udpakning:

• One (1) Waring Commercial WSB60ST 16-Inch Immersion Blender Shaft

4. Opsætning

The WSB60ST shaft is designed for easy interchangeability with compatible Waring Big Stix immersion blender power units. Compatible models include WSB25X, WSB50, WSB55, WSB60, WSB65, WSB70, and WSBPPW.

1. Ensure Power Unit is Off and Unplugged: Before attaching or detaching the shaft, always ensure the immersion blender power unit is switched off and disconnected from the power supply.
2. Juster og fastgør: Align the top of the WSB60ST shaft with the coupling mechanism on the bottom of the power unit. Push the shaft firmly upwards and twist clockwise until it locks securely into place.
3. Bekræft forbindelsen: Gently pull down on the shaft to ensure it is fully engaged and will not detach during operation.

5. Betjeningsvejledning

Once the WSB60ST shaft is securely attached to a compatible Waring Big Stix power unit, you can proceed with blending operations. Refer to your power unit's instruction manual for specific operating procedures, speed controls, and safety guidelines.

• Forbered ingredienser: Place ingredients in a suitable container for blending. Ensure the container is deep enough to accommodate the 16-inch shaft and prevent splashing.
• Immerse Shaft: With the power unit unplugged, immerse the blending end of the shaft into the ingredients before turning on the power. Ensure the liquid level does not exceed the maximum immersion line, if indicated on your power unit.
• Start blendning: Plug in the power unit and select the desired speed setting. Begin blending, moving the shaft gently up and down and around the container to ensure thorough processing.
• Færdig blanding: Once blending is complete, turn off the power unit and unplug it from the outlet. Remove the shaft from the ingredients.

6. Vedligeholdelse og rengøring

Proper cleaning and maintenance extend the life of your immersion blender shaft and ensure hygienic operation.

1. Afbryd strømmen: Always unplug the power unit from the electrical outlet before cleaning or performing any maintenance.
2. Detach Shaft: Twist the shaft counter-clockwise and pull down to detach it from the power unit.
3. Rensning: The WSB60ST shaft is completely sealed and dishwasher safe. For manual cleaning, wash the shaft thoroughly with warm, soapy water. Use a brush to clean around the blade area carefully. Rinse thoroughly with clean water.
4. Tørring: Allow the shaft to air dry completely before storage or reattachment.
5. Opbevaring: Store the shaft in a clean, dry place.

7. Fejlfinding

If you encounter issues with your WSB60ST immersion blender shaft, consider the following:

• Shaft not attaching securely: Ensure the shaft is aligned correctly with the power unit's coupling and twisted until it locks. Check for any obstructions in the coupling mechanism.
• Poor blending performance: This is typically related to the power unit or the ingredients. Ensure the power unit is functioning correctly and that ingredients are suitable for immersion blending.
• Usædvanlig støj eller vibrationer: Discontinue use immediately. Check for any damage to the shaft or blade. If damage is present, replace the shaft.

For issues not resolved by these steps, contact Waring Commercial customer support.

8. Specifikationer

9. Garanti og support

For information regarding warranty coverage, service, or technical support for your Waring Commercial products, please refer to the documentation provided with your original Waring Big Stix immersion blender power unit or visit the official Waring Commercial webwebsted. Behold din købskvittering som købsbevis i tilfælde af garantikrav.

Fabrikant: Conair LLC Waring Commercial Inc. (BISS)