APC Smart-UPS RT 3000VA 208V 3U rackmonteret UPS-system brugermanual

Indledning

This manual provides essential instructions for the safe installation, operation, and maintenance of your APC Smart-UPS RT 3000VA 208V 3U Rackmount UPS System. This Uninterruptible Power Supply (UPS) is designed to provide reliable power protection for your critical electronic equipment, ensuring continuous operation during power outages og udsving.

Vigtige sikkerhedsinstruktioner

Please read these instructions carefully before installing, operating, servicing, or maintaining the equipment. Failure to follow these instructions can result in serious injury or equipment damage.

• Denne UPS indeholder farlige stoffertages. Do not attempt to disassemble the unit.
• Service af batterier bør udføres eller overvåges af personale, der har kendskab til batterier og de nødvendige forholdsregler.
• Bortskaf ikke batterier i åben ild. Batterierne kan eksplodere.
• Do not open or mutilate the batteries. Released electrolyte is harmful to the skin and eyes.
• Before installing or replacing the batteries, remove conductive jewelry such as chains, wristwatches, and rings.
• UPS'en skal være tilsluttet en jordet vekselstrømsstikkontakt.
• Ensure proper ventilation around the UPS.

Opsætning og installation

1. Udpakning og inspektion

Carefully unpack the UPS and inspect it for any shipping damage. Report any damage to the carrier and your dealer. The package should contain the UPS unit, rackmount hardware, and documentation.

2. Physical Installation (Rackmount)

The APC Smart-UPS RT 3000VA is designed for 3U rackmount installation. Use the provided rackmount hardware to secure the unit in a standard 19-inch equipment rack. Ensure adequate space for airflow around the unit.

Figur 1: Front view of the APC Smart-UPS RT 3000VA 3U Rackmount UPS System with rackmount ears attached, ready for installation. The front panel features status indicators and control buttons.

3. Batteritilslutning

The UPS ships with internal batteries disconnected for safety. Locate the battery connector on the rear or front panel (refer to the specific model diagram if available) and firmly connect the battery cables. The UPS will not power on or provide backup power until the batteries are connected.

4. Elektriske forbindelser

• Indgangseffekt: Connect the UPS input power cord (NEMA L6-30P) to a dedicated 208V or 240V (configurable) AC power source. Ensure the circuit can handle the UPS's maximum input current.
• Outputenheder: Connect your critical equipment to the UPS output receptacles (2x NEMA L6-20R, 2x NEMA L6-30R). Do not overload the UPS.

Figur 2: Side view of the APC Smart-UPS RT 3000VA 3U Rackmount UPS System, showing the depth of the unit and ventilation grilles. This perspective highlights the robust construction for rack integration.

5. Første opstart

After all connections are secure, press the power button on the front panel to turn on the UPS. The UPS will perform a self-test and the status indicators will illuminate. Allow the batteries to charge for at least 24 hours to ensure full runtime capacity.

Operation

Frontpanel display og kontroller

The front panel features an LED status display with load and battery bar-graphs, along with indicators for On Line, On Battery, Replace Battery, Overload, and Bypass. Control buttons allow for power on/off, self-test, and menu navigation.

Normal drift

Under normal conditions, the UPS operates in "On Line" mode, providing conditioned power to connected equipment and charging the batteries. The "On Line" indicator will be illuminated.

Om batteridrift

Under en magt outage eller betydelig volumentage fluctuation, the UPS automatically transfers to battery power. The "On Battery" indicator will illuminate, and an audible alarm may sound. The UPS will provide power for approximately 14.1 minutes at full load (2100 Watts) with standard battery configuration.

Bypass drift

The UPS features an internal bypass (automatic and manual). In bypass mode, utility power is supplied directly to the connected equipment, bypassing the UPS's power conditioning circuitry. This mode is typically used for maintenance or in case of an internal UPS fault. The "Bypass" indicator will be illuminated.

Emergency Power Off (EPO)

The UPS includes an Emergency Power Off (EPO) port. Connecting an EPO switch to this port allows for immediate shutdown of the UPS and connected equipment in an emergency situation. Refer to the installation guide for EPO connection details.

Opretholdelse

Udskiftning af batteri

The UPS uses maintenance-free sealed Lead-Acid batteries. The "Replace Battery" indicator will illuminate when the batteries need replacement. Batteries are hot-swappable, meaning they can be replaced without powering down the connected equipment. Refer to the specific battery replacement instructions provided with your replacement battery modules. Typical recharge time for new batteries is 2.5 hours.

Rensning

Keep the UPS free of dust and debris. Use a dry cloth to clean the exterior. Do not use liquid cleaners or solvents.

Firmware opdateringer

Periodically check the APC website for available firmware updates for your UPS model. Firmware updates can provide improved performance, features, and bug fixes. Follow the instructions provided with the firmware update package carefully.

Fejlfinding

Dette afsnit indeholder løsninger på almindelige problemer. Kontakt APC's tekniske support ved mere komplekse problemer.

Specifikationer

Garanti og support

Garantioplysninger

APC provides a two-year warranty for this product. Please retain your proof of purchase for warranty claims. The warranty covers defects in materials and workmanship under normal use.

Teknisk support

For technical assistance, troubleshooting, or warranty service, please contact APC customer support. Visit the official APC webwebsted for kontaktoplysninger, ofte stillede spørgsmål og yderligere ressourcer.

APC Webwebsted: www.apc.com