Metabo WEA 14-125 Plus Vinkelsliber Brugermanual

1. Produktet er slutview

The Metabo WEA 14-125 Plus is a powerful 125 mm angle grinder designed for various grinding and cutting applications. This manual provides essential information for safe operation, maintenance, and troubleshooting to ensure optimal performance and longevity of your tool.

This image displays the Metabo WEA 14-125 Plus Angle Grinder. It features a dark green and black body with a silver-colored gear housing. A red side handle with the 'metabo' logo is attached, and a grinding wheel is visible under the protective guard. The power cord extends from the rear of the tool.

2. Sikkerhedsinstruktioner

Overhold altid følgende sikkerhedsforanstaltninger for at forhindre elektrisk stød, brand og alvorlig personskade.

• Sikkerhed på arbejdsområdet: Hold arbejdsområdet rent og godt oplyst. Rodede eller mørke områder indbyder til ulykker. Brug ikke elværktøj i eksplosive atmosfærer, f.eks. i nærheden af ​​brandfarlige væsker, gasser eller støv.
• Elektrisk sikkerhed: Stik på elværktøj skal passe til stikkontakten. Modificer aldrig stikket på nogen måde. Undgå kropskontakt med jordforbundne overflader såsom rør, radiatorer, komfurer og køleskabe.
• Personlig sikkerhed: Always wear eye protection. Use hearing protection when operating the tool. Wear a dust mask if operations create dust. Do not overreach. Keep proper footing and balance at all times.
• Brug og vedligeholdelse af elværktøj: Tving ikke elværktøjet. Brug det korrekte elværktøj til din anvendelse. Tag stikket ud af strømkilden, før du foretager justeringer, skifter tilbehør eller opbevarer elværktøj.
• Specifik sikkerhed for vinkelslibere:
  • Always use the guard provided with the tool.
  • Ensure the grinding wheel is correctly mounted and tightened before use.
  • Brug ikke beskadiget eller forkert tilbehør.
  • Lad værktøjet nå fuld hastighed, før det påføres på emnet.
  • Vær opmærksom på tilbageslag og hvordan du undgår det.

3. Opsætning

Before operating the angle grinder, ensure it is properly set up.

1. Udpakning: Carefully remove the angle grinder and all accessories from the packaging. Inspect for any damage. Do not use the tool if any part is damaged.
2. Fastgørelse af sidehåndtaget: The side handle can be screwed into either the left or right side of the gear housing, depending on user preference and application. Ensure it is securely tightened.

   Refer to the product image for the typical placement of the side handle.

3. Montering af slibeskiven:
   • Sørg for, at værktøjet er frakoblet strømkilden.
   • Tryk på spindellåseknappen for at fastgøre spindlen.
   • Placer den indre flange på spindlen.
   • Position the grinding wheel (e.g., 125 mm abrasive wheel, Type 27) onto the inner flange, ensuring it sits flush.
   • Skru den ydre flange (cl) fastampmøtrik) på spindlen.
   • Use the spanner wrench to firmly tighten the outer flange while holding the spindle lock.
4. Adjusting the Guard: The protective guard must always be used. Adjust its position to provide maximum protection for the operator, directing sparks and debris away from the user. Loosen the guard's clampskruen, drej beskyttelsesskærmen til den ønskede position, og spænd derefter skruen forsvarligt.

4. Betjeningsvejledning

Følg disse trin for sikker og effektiv drift.

1. Tænd/sluk:
   • To switch on, slide the switch forward. For continuous operation, press the front part of the switch down until it locks.
   • To switch off, release the switch. If locked for continuous operation, press the rear part of the switch to release it.
2. Slibning:
   • Hold godt fast i værktøjet med begge hænder.
   • Allow the grinding wheel to reach full speed before contacting the workpiece.
   • Apply light, even pressure. Do not press too hard, as this can reduce wheel life and motor efficiency.
   • Maintain an angle of approximately 15-30 degrees between the grinding wheel and the workpiece surface for optimal material removal.
3. Skæring:
   • For cutting, use appropriate cutting discs and ensure the guard is correctly positioned.
   • Hold the tool firmly. Make straight cuts without tilting the disc.
   • Do not apply side pressure to the cutting disc, as this can cause it to bind or break.
   • Sørg for, at arbejdsemnet er sikkert klampudg.

5. Vedligeholdelse

Regular maintenance ensures the longevity and safe operation of your Metabo angle grinder.

• Rensning: Regularly clean the ventilation slots to prevent overheating. Use a soft brush or compressed air. Do not use water or solvents.
• Kulbørster: This tool uses carbon brushes. If the motor sparks excessively or the tool loses power, the carbon brushes may need replacement. This should ideally be performed by a qualified service technician.
• Strømledning: Inspect the power cord regularly for damage. If damaged, have it replaced by a qualified electrician to avoid electrical hazards.
• Generel inspektion: Periodically check all screws and fasteners for tightness. Ensure the guard and side handle are securely attached.

6. Fejlfinding

Se dette afsnit for almindelige problemer og deres løsninger.

7. Tekniske specifikationer

Key technical data for the Metabo WEA 14-125 Plus Angle Grinder.

• Mærke: Metabo
• Modelnummer: 601105000
• Magt: 1400 watt
• Voltage: 230 volt
• Grinding Wheel Diameter: 125 mm
• Spindel gevind: M 14
• Produktmål (L x B x H): 13 x 37.2 x 12.4 cm
• Vægt: 2000 gram (2 kg)
• Strømkilde: Elektrisk med ledning
• Materiale: Plast
• Farve: Grøn

8. Garanti og support

For warranty information, service, or technical support, please refer to the documentation provided with your purchase or contact Metabo customer service directly. Keep your proof of purchase for warranty claims.

You can find more information on the official Metabo webwebsted: www.metabo.com