RAB Lighting LFP16A Sleek projektør brugermanual

1. Produktet er slutview

The RAB Lighting LFP16A Sleek Floodlight is designed for outdoor illumination, providing efficient and durable lighting. This fixture accommodates a PAR16 type bulb and features a robust die-cast aluminum housing with a powder-coated finish for enhanced durability and weather resistance.

Nøglefunktioner:

• Designed for 60W PAR16 bulbs, delivering 650 lumens output (bulb not included).
• Durable die-cast aluminum housing with a powder-coated finish.
• Gasket and O-ring seals provide resistance against weather elements.
• Integrated shield helps reduce glare.
• Equipped with a 1/2" NPS threaded arm for secure mounting and a locking swivel for adjustable positioning.

Figure 1: RAB Lighting LFP16A Sleek Floodlight. This image shows the floodlight fixture with its threaded arm and wiring, highlighting its compact and durable design.

2. Sikkerhedsoplysninger

Læs og forstå alle instruktioner, før du installerer eller bruger dette produkt. Manglende overholdelse af disse instruktioner kan resultere i elektrisk stød, brand eller andre farer, der kan forårsage materielle skader eller personskade.

• Elektrisk sikkerhed: Always disconnect power at the circuit breaker or fuse box before wiring or servicing the fixture.
• Uddannet elektriker: Installationen skal udføres af en kvalificeret elektriker i overensstemmelse med alle lokale og nationale el-forskrifter.
• Jording: Sørg for, at armaturet er korrekt jordforbundet for at undgå potentielle elektriske farer.
• Pære type: Use only PAR16 type bulbs with a maximum wattagpå 60 W. Overskridelse af den maksimale watttage kan forårsage overophedning og beskadigelse af armaturet.
• Våd placering: This fixture is suitable for wet locations. Ensure all connections are properly sealed and waterproofed during installation.
• Temperatur: Do not install near combustible materials or surfaces that may be affected by heat.

3. Pakkens indhold

Kontroller, at alle komponenter er til stede, før installationen påbegyndes:

• RAB Lighting LFP16A Sleek Floodlight Fixture (1)
• Instruktionsmanual (1)

Note: Light bulb and wire connectors are not included and must be purchased separately.

4. Opsætning og installation

This floodlight is designed for wall mounting and features a 1/2" NPS threaded arm for secure attachment to a junction box or mounting accessory. Follow these steps for proper installation:

1. Forbered til installation:
   • Turn off power at the circuit breaker before starting any electrical work.
   • Gather necessary tools: screwdriver, wire strippers, electrical tape, silicone sealant (for waterproofing).
2. Monter armaturet:
   • Thread the 1/2" NPS arm of the floodlight into a compatible outdoor junction box or mounting plate. Ensure a tight and secure connection.
   • Use the locking swivel to adjust the initial angle of the fixture.
   

   Figure 2: Detail of the 1/2" NPS threaded arm and 180-degree adjustable swivel. This illustrates the mounting mechanism and flexibility of the floodlight.
3. Ledningsforbindelser:
   • Connect the black wire from the fixture to the hot (black) wire from the power supply.
   • Connect the white wire from the fixture to the neutral (white) wire from the power supply.
   • Connect the bare copper or green wire from the fixture to the ground wire from the power supply.
   • Secure all connections with appropriate wire connectors and electrical tape. For outdoor installations, consider using silicone-filled wire nuts for added moisture protection.
4. Installer pære:
   • Carefully insert a PAR16 bulb (max 60W) into the fixture socket. Do not overtighten.
5. Seal and Test:
   • Ensure all connections are secure and the fixture is properly sealed against moisture. Apply silicone sealant around the mounting base if necessary.
   • Restore power at the circuit breaker and test the floodlight's operation.

5. Betjeningsvejledning

Once installed and powered, the RAB Lighting LFP16A Floodlight operates by the control of the circuit it is connected to (e.g., a wall switch, timer, or photocell). There are no direct controls on the fixture itself.

• Justering af lysretning: The fixture features a locking swivel arm. To adjust the light direction, loosen the locking nut on the swivel, position the floodlight as desired, and then tighten the locking nut securely.
• Reduktion af blænding: The built-in shield is designed to minimize glare, directing light effectively to the intended area.

Figur 3: Eksample of the LFP16A floodlight used in a landscape setting, demonstrating its illumination capabilities.

6. Vedligeholdelse

Regelmæssig vedligeholdelse sikrer optimal ydeevne og levetid for din projektør.

• Rensning: Rengør armaturets yderside regelmæssigt med en blød, tør klud.amp cloth. Do not use abrasive cleaners or solvents, as these can damage the finish. Ensure power is off before cleaning.
• Udskiftning af pære:
  1. Sluk for strømmen til armaturet ved afbryderen.
  2. Allow the old bulb to cool completely before handling.
  3. Carefully unscrew and remove the old PAR16 bulb.
  4. Insert a new PAR16 bulb (max 60W) into the socket, ensuring it is seated correctly.
  5. Genopret strømmen og test den nye pære.
• Inspektion: Annually inspect the fixture for any signs of wear, damage, or loose connections. Address any issues promptly.

7. Fejlfinding

8. Specifikationer

9. Garanti og support

The RAB Lighting LFP16A Sleek Floodlight comes with a 1 års producentgaranti fra købsdatoen. Denne garanti dækker fejl i materialer og udførelse ved normal brug.

For warranty claims, technical support, or further assistance, please contact RAB Lighting customer service. Refer to the official RAB Lighting webhjemmeside for de seneste kontaktoplysninger.

Fabrikant: RAB belysning

Webwebsted: www.rablighting.com (Eksamplinket, det faktiske link kan variere)