Brugervejledning til Simrad TP10 Rorpindpilot

1. Introduktion

The Simrad TP10 Tiller Pilot is an essential marine electronic device designed for use on sailboats up to 33 feet or 3.7 tons. This compact and robust autopilot provides reliable steering assistance, allowing sailors to maintain course with ease. It features an intuitive LED display and straightforward pushbutton controls for simple operation. The internal fluxgate compass ensures accurate heading information.

Nøglefunktioner omfatter:

• Nem at bruge: Simple controls for straightforward adjustments.
• Precision Steering: Maintains course effectively in various conditions, including challenging weather.
• Batterioptimering: Designed for low power consumption to extend battery life during prolonged use.
• Lydløs drift: Engineered for minimal noise, enhancing the peaceful experience on the water.
• Waterproof Sealing: Provides protection against marine elements.

2. Sikkerhedsoplysninger

Always prioritize safety when operating marine electronic equipment. Read and understand all instructions before installation and use. Failure to do so may result in damage to the product, vessel, or personal injury.

• Sørg for, at strømforsyningen er afbrudt, før du udfører nogen form for installation eller vedligeholdelse.
• Verify all electrical connections are secure and properly insulated to prevent short circuits and corrosion.
• Forsøg ikke selv at skille eller reparere enheden. Kontakt kvalificeret servicepersonale.
• Always maintain a vigilant watch and be prepared to take manual control of the vessel, especially in adverse weather conditions or congested waters.
• Keep the unit clear of obstructions that could impede its movement or function.

3. Pakkens indhold

Når du åbner pakken, skal du kontrollere, at alle komponenter er til stede og ubeskadigede:

• Simrad TP10 Tiller Pilot Unit
• Monteringsbeslag og hardware
• Strømkabel
• Brugervejledning og dokumentation

4. Opsætning

4.1 Mounting the Tiller Pilot

The TP10 Tiller Pilot should be mounted securely to the vessel's structure, ensuring it has a clear range of motion to connect to the tiller arm. Choose a location that provides easy access to the controls and is protected from direct impact.

1. Identify a suitable mounting point on the cockpit coaming or a sturdy bulkhead, ensuring it aligns correctly with the tiller arm.
2. Brug det medfølgende monteringsbeslag som skabelon til at markere boresteder.
3. Drill pilot holes and secure the mounting bracket using appropriate marine-grade fasteners.
4. Attach the TP10 unit to the mounting bracket.
5. Connect the tiller pilot's pushrod to the tiller arm using the appropriate pin or fitting. Ensure the connection allows for smooth movement and full range of steering.

4.2 Strømtilslutning

The Simrad TP10 operates on a 12 VDC power supply.

1. Connect the red wire from the power cable to the positive (+) terminal of your 12 VDC power source.
2. Connect the black wire to the negative (-) terminal or a suitable ground point.
3. It is recommended to install an in-line fuse (e.g., 10 Amp) on the positive power lead, close to the power source, to protect the unit from overcurrent.
4. Ensure all connections are watertight and corrosion-resistant.

5. Betjeningsvejledning

The TP10 Tiller Pilot features intuitive controls for easy operation.

5.1 kontroller overview

• STBY/AUTO Button (Red): Toggles between Standby and Auto modes. In Standby, the pilot is disengaged, allowing manual steering. In Auto mode, the pilot maintains the set course.
• Arrow Buttons (Blue, Up/Down): Used to adjust the course in Auto mode. Pressing the up arrow will steer the boat to starboard, and the down arrow to port.
• TACK Button: Initiates a tack maneuver, automatically turning the boat through a pre-set angle.
• CAL-knap: Used for calibration procedures.
• LED-indikatorer: Provide visual feedback on the unit's status (e.g., red for standby, green for auto).

5.2 Grundlæggende betjening

1. Tænd: Ensure the unit is properly connected to power. The unit will typically power on in Standby mode, indicated by a red LED.
2. Engaging Auto Mode: Once you are on your desired course, press the STBY/AUTO button. The LED indicator will change to green, and the tiller pilot will engage, holding the current heading.
3. Course Adjustment: Mens du er i Auto-tilstand, skal du bruge Pileknapper to make small course corrections. Each press will typically adjust the course by a few degrees.
4. Disengaging Auto Mode: To return to manual steering, press the STBY/AUTO button again. The unit will revert to Standby mode (red LED), and you can take control of the tiller.
5. Tack Maneuver: To perform a tack, ensure you are in Auto mode and press the TAK button. The pilot will automatically turn the boat through the pre-programmed tack angle.

The internal fluxgate compass provides accurate heading information, allowing the TP10 to maintain a precise course. The unit's robust design ensures reliable performance even in challenging marine environments.

6. Vedligeholdelse

Regular maintenance ensures the longevity and optimal performance of your Simrad TP10 Tiller Pilot.

• Rensning: Periodically wipe down the unit with a damp cloth to remove salt residue, dirt, and grime. Avoid using abrasive cleaners or solvents.
• Inspektion: Regularly inspect the power cable for any signs of wear, fraying, or damage. Check the mounting bracket and tiller arm connection for security.
• Smøring: Ensure the pushrod mechanism is clean and moves freely. Lightly lubricate the moving parts with a marine-grade lubricant if necessary, following manufacturer recommendations.
• Opbevaring: If storing the vessel for an extended period, disconnect the tiller pilot and store it in a dry, protected environment.

7. Fejlfinding

This section provides solutions to common issues you might encounter with your TP10 Tiller Pilot.

8. Specifikationer

9. Garanti og support

The Simrad TP10 Tiller Pilot comes with a 2 års producentgaranti. Denne garanti dækker fejl i materialer og udførelse ved normal brug.

For technical support, warranty claims, or service inquiries, please contact Simrad customer support. Refer to the official Simrad webwebstedet eller dokumentationen, der følger med dit produkt, for at få de seneste kontaktoplysninger.

Vigtig: Any unauthorized attempts to open or repair the unit may void the warranty.