Indledning
The Clore Automotive Jump-N-Carry JNC4000 is a powerful and reliable 12V jump starter designed to provide instant starting power for a wide range of vehicles. Featuring Clore PROFORMER battery technology, industrial-grade clamps, and a built-in charger, this unit is engineered for durability and performance. This manual provides essential information for the safe and effective operation, maintenance, and troubleshooting of your JNC4000.
Billede: Forside view of the Clore Automotive Jump-N-Carry JNC4000 jump starter, showcasing det er rødt casing, integrated cables, and control panel with a voltmeter and charging status indicators.
Vigtige sikkerhedsoplysninger
Read and understand all safety information before using this product. Failure to follow these instructions may result in electric shock, fire, or serious injury.
- Øjenbeskyttelse: Brug altid sikkerhedsbriller, når du arbejder med batterier.
- Ventilation: Ensure adequate ventilation when charging or jump starting, as batteries can produce explosive gases.
- Gnister og flammer: Keep sparks, flames, and smoking materials away from the battery and jump starter.
- Korrekt forbindelse: Tilslut clamps in the correct order to avoid sparks and damage. Always connect the positive (+) clamp first, then the negative (-) clamp.
- Børn og kæledyr: Keep the jump starter out of reach of children and pets.
- Beskadiget enhed: Do not operate the unit if it is damaged or has been dropped.
- Opladning: Only charge the unit using the specified charging method.
Opsætning og første opladning
Before first use, fully charge your JNC4000 jump starter. This ensures optimal performance and extends battery life.
Hvad er der i æsken:
- (1) JNC4000 Jump Starter
- (1) 12V male-male cable (for charging)
Opladningsinstruktioner:
- Locate the AC charging port on the front of the JNC4000 unit.
- Connect a standard extension cord (not included) to the AC charging port on the unit.
- Sæt den anden ende af forlængerledningen i en standard 120V AC stikkontakt.
- The "CHARGING" indicator light on the unit will illuminate, indicating that charging has begun.
- Allow the unit to charge for a minimum of 24 hours for the initial charge. Subsequent charges may take less time.
- The "CHARGING COMPLETE" indicator light will illuminate when the unit is fully charged.
Image: Close-up of the charging status indicators on the JNC4000, showing "CHARGING COMPLETE" and "CHARGING" lights.
Brugsanvisning: Start af et køretøj med startkabler
Follow these steps carefully to safely jump start a vehicle.
- Forberedelse: Ensure the vehicle's ignition is off and all accessories (lights, radio, etc.) are turned off. Place the vehicle in park (automatic) or neutral (manual) and engage the parking brake.
- Tilslut positiv Clamp: Tilslut den røde positive (+) clamp of the JNC4000 to the positive (+) terminal of the vehicle's discharged battery. Ensure a solid connection.
- Tilslut negativ Clamp: Tilslut den sorte negative (-) clamp of the JNC4000 to a clean, unpainted metal part of the vehicle's engine block or chassis, away from the battery and fuel lines. Do not connect directly to the negative battery terminal.
- Start køretøj: Når begge clamps are securely connected, attempt to start the vehicle. Crank the engine for no more than 5-6 seconds. If the vehicle does not start, wait at least 3 minutes before attempting again to allow the jump starter to cool.
- Afbryd Clamps: Når køretøjet starter, skal den sorte negative (-) pol afbrydes.amp first, then disconnect the red positive (+) clamp.
- Genoplad: Immediately recharge the JNC4000 after each use to ensure it is ready for the next time it is needed.
Image: A person's hand connecting the red positive clamp of a jump starter to a car battery's positive terminal under the hood of a vehicle.
Opretholdelse
Proper maintenance will ensure the longevity and reliability of your JNC4000.
- Regelmæssig genopladning: Recharge the unit after every use. If not used, recharge every 30-60 days to maintain the internal battery's health.
- Opbevaring: Store the unit in a cool, dry place, ideally above 50°F (10°C). Avoid extreme temperatures.
- Rensning: Keep the unit clean and free of dirt, grease, and moisture. Use a dry cloth for cleaning.
- Kabel og Clamp Inspektion: Kontrollér kabler og koblinger regelmæssigtampKontroller for tegn på skader, flosning eller korrosion. Udskift om nødvendigt.
Fejlfinding
| Problem | Mulig årsag | Løsning |
|---|---|---|
| Unit does not turn on/no power. | Internt batteri er afladet. | Genoplad enheden helt. |
| Køretøjet starter ikke efter forsøg på at hoppe. | Poor connection; severely discharged vehicle battery; vehicle issue. | Tjek klamp connections for tightness and cleanliness. Allow unit to cool for 3 minutes before re-attempting. If still no start, vehicle may have other issues. |
| Charging indicator not illuminating. | Extension cord not plugged in; faulty outlet; unit already fully charged. | Ensure extension cord is securely plugged into unit and wall outlet. Test outlet with another device. Check if "CHARGING COMPLETE" light is on. |
Specifikationer
| Feature | Detalje |
|---|---|
| Mærke | Clore Automotive |
| Model | Jnc4000 |
| Spids Ampslette | 1100 Amps |
| Knæk Ampslette | 325 Amps |
| Batteriteknologi | Clore PROFORMER |
| Produktmål (D x B x H) | 14.5 cm x 5.5 cm x 16.6 cm |
| Varens vægt | 18 pund |
| Indbygget oplader | Ja |
| UPC | 747410990568 |
Image: Diagram showing the dimensions of the JNC4000 jump starter: 14.5 inches deep, 5.5 inches wide, and 16.6 inches high.
Garanti og support
Clore Automotive products are designed for durability and performance. For specific warranty details and support, please refer to the warranty card included with your product or visit the official Clore Automotive webwebsted.
Officiel Webwebsted: www.cloreautomotive.com
For customer service inquiries, please contact Clore Automotive directly through their webwebstedet eller kontaktoplysningerne på din produktemballage.
