Indledning
This manual provides instructions for the installation, operation, and maintenance of your Honeywell TH5110D1006/U Non-Programmable Thermostat. This thermostat is designed for simple and reliable control of your heating and cooling system.
It features a large, clear backlit digital display for easy viewing of both room and set temperatures, and offers basic control for 1 Heat/1 Cool conventional systems and heat pumps without auxiliary heat.
Sikkerhedsoplysninger
- Sluk altid for strømmen til varme-/kølesystemet ved hovedsikringen eller afbryderpanelet, før du installerer eller servicerer termostaten.
- Installationen skal udføres af en kvalificeret tekniker.
- Do not short (jumper) across the electrical terminals on the thermostat. This can damage the thermostat and/or the heating/cooling system.
- This thermostat is designed for 24 Vac conventional and heat pump systems or 750 mV heating systems. Ensure compatibility with your HVAC system.
Produkt overview
Figur 1: Honeywell TH5110D1006/U Non-Programmable Thermostat. This image shows the front view of the thermostat with its digital display and control buttons.
The Honeywell TH5110D1006/U thermostat features a large, clear backlit digital display for easy viewing. It includes simple push-button controls for adjusting temperature, fan settings, and system mode. The unit is dual-powered, operating on either 2 AA batteries or hardwired to your system.
Opsætning
1. Installation
For detailed wiring instructions, please refer to the installation guide provided with your thermostat packaging. It is recommended that a qualified HVAC technician performs the installation to ensure proper wiring and system compatibility.
2. Tænd for enheden
Termostaten kan forsynes med strøm på to måder:
- Batteridrevet: Requires 2 AA alkaline batteries (not included). The thermostat features an easy-access battery replacement door. A "Replace Battery" indicator will appear on the display when batteries are low.
- Hardwired: Can be hardwired to your HVAC system for continuous power. Batteries can still be installed as a backup.
3. Initial Configuration (Installer Setup)
After installation, the thermostat may require initial configuration to match your specific HVAC system (e.g., conventional or heat pump, gas or electric heat). This is typically done through an "Installer Setup" menu, often accessed by holding specific buttons (e.g., Fan and Up buttons) for a few seconds. Refer to your detailed installation manual for specific steps to configure system type and other advanced settings.
Betjeningsvejledning
1. Justering af temperatur
Brug Op (▲) og Ned (▼) Brug pileknapperne på højre side af termostaten til at indstille den ønskede temperatur. Displayet viser både den aktuelle rumtemperatur og den indstillede temperatur.
2. Ventilatorindstillinger
Tryk på Ventilator button (left button below the display) to cycle through the fan modes:
- Auto: Ventilatoren kører kun, når varme- eller kølesystemet er aktivt i drift. Dette er den mest energieffektive indstilling.
- På: The fan runs continuously, regardless of whether the heating or cooling system is active. This can help with air circulation.
3. Systemtilstand
Tryk på System button (right button below the display) to cycle through the system modes:
- Afkøle: The thermostat will activate your cooling system to maintain the set temperature.
- Varme: The thermostat will activate your heating system to maintain the set temperature.
- Slukket: Turns off both heating and cooling systems. The fan can still be operated manually if set to "On".
- EmHeat (Emergency Heat): (If applicable to your system) Used for heat pumps when the outdoor temperature is too low for the heat pump to operate efficiently, or if the heat pump requires service. This mode uses auxiliary heat.
- Auto: (If applicable to your system) The thermostat automatically switches between heating and cooling to maintain the set temperature range.
4. Backlight Feature
The large digital display is backlit for easy viewing, especially in low-light conditions. The backlight typically activates when any button is pressed and remains on for a short period.
Opretholdelse
1. Udskiftning af batteri
When the "Replace Battery" indicator appears on the display, it's time to replace the 2 AA alkaline batteries. The thermostat features an easy-access battery compartment, usually located on the side or front of the unit. Slide open the compartment, remove old batteries, and insert new ones, ensuring correct polarity. The thermostat settings are typically retained during battery replacement if done promptly.
2. Rensning
Rengør termostatens yderside med en blød, tør klud.amp klud. Brug ikke slibende rengøringsmidler eller opløsningsmidler, da disse kan beskadige overfladen eller de indvendige komponenter.
Fejlfinding
| Problem | Mulig årsag | Løsning |
|---|---|---|
| Skærmen er tom | Ingen strøm, døde batterier. | Replace batteries or check circuit breaker/power supply. |
| Ingen opvarmning/køling | Incorrect system mode, thermostat setting too high/low, power issue. | Verify system mode (Heat/Cool), adjust set temperature, check power. If issue persists, contact a qualified technician. |
| Fan runs continuously in Auto mode | Fan setting is "On" instead of "Auto". | Press the Fan button to select "Auto". |
| Temperaturaflæsningen virker unøjagtig | Termostatens placering, træk eller direkte sollys. | Ensure thermostat is not in direct sunlight or near drafts. Allow time for temperature stabilization. |
If you encounter problems that cannot be resolved using the troubleshooting steps above, please contact a qualified HVAC service professional.
Specifikationer
- Model: TH5110D1006/U
- Mærke: Honeywell
- Dimensioner: 1.5" D x 3.4" B x 4.5" H
- Controller type: Tryk knap
- Speciel funktion: Non-Programmable (Note: While some product data may list 'Programmable', this model is specifically designed as a non-programmable thermostat for straightforward operation.)
- Farve: Premier White
- Kompatible systemer: 1 Heat/1 Cool Conventional Systems, Heat Pumps (no auxiliary heat)
- Strømkilde: Dual-powered (2 AA batteries and/or hardwire)
- Voltage: 30 Volts (for hardwired connection)
- Skærmtype: Digital with Backlight
- Skærmstørrelse: 1.5 tommer
- Monteringstype: Vægmontering
Officielle produktvideoer
No official product videos from a 'Seller' were found in the provided data that meet the embedding criteria.
Garanti og support
For warranty information or technical support, please refer to the documentation included with your product or visit the official Honeywell website. You can also contact Honeywell customer service for assistance with your TH5110D1006/U thermostat.
