1. Introduktion
The Gardner Bender AMT-113 Xtreme Environment Spade Terminal is designed to create secure, insulated, and moisture-resistant electrical connections. These terminals are suitable for 16-14 AWG (American Wire Gauge) wires and feature heat-shrink insulation for enhanced protection against environmental factors such as moisture intrusion and abrasion. They are ideal for automotive and marine applications where reliable connections are critical.
Figure 1: Gardner Bender AMT-113 Xtreme Environment Spade Terminal with heat-shrink insulation.
2. Sikkerhedsoplysninger
Overhold altid følgende sikkerhedsforanstaltninger, når du arbejder med elektriske komponenter:
- Ensure power is disconnected before installing or removing terminals.
- Brug passende personlige værnemidler (PPE), såsom sikkerhedsbriller.
- Use tools specifically designed for electrical work, such as insulated crimping tools.
- Never exceed the specified voltage or temperature ratings of the terminal.
- Hold børn og uautoriseret personale væk fra arbejdsområdet.
3. Opsætning og installation
Follow these steps for proper installation of the spade terminal:
- Forbered ledningen: Strip approximately 3/8 inch (9.5 mm) of insulation from the end of the 16-14 AWG wire. Ensure the copper strands are clean and untwisted.
- Indsæt ledningen: Insert the stripped wire completely into the metal barrel of the spade terminal. Ensure no bare wire strands are exposed outside the terminal barrel.
- Klem terminalen: Using a suitable crimping tool, crimp the terminal barrel firmly onto the wire. Apply sufficient pressure to ensure a secure mechanical and electrical connection. A proper crimp should be tight and not allow the wire to be pulled out.
- Påfør varme: Using a heat gun (not an open flame), apply even heat to the heat-shrink insulation sleeve of the terminal. Move the heat gun slowly and evenly around the sleeve until it shrinks tightly around the wire insulation and the terminal barrel. The heat-shrink material will conform to the wire, creating a waterproof and strain-relieved seal.
- Connect to Stud: Once cooled, connect the spade end of the terminal to an appropriate stud (typically sizes 8-10) and secure it with a nut or screw.
Figur 2: Forside view of the spade terminal, showing the U-shaped connector.
4. Driftsprincipper
Once properly installed, the Gardner Bender AMT-113 terminal provides a reliable electrical connection. The copper contact material ensures excellent conductivity, while the polyvinyl chloride (PVC) heat-shrink insulation offers superior protection against moisture, corrosion, and physical abrasion. This design maintains circuit integrity in challenging environmental conditions, preventing shorts and ensuring consistent power flow.
5. Vedligeholdelse
These terminals are designed for long-term reliability with minimal maintenance. However, periodic inspection of electrical connections in harsh environments is recommended:
- Visually inspect connections for any signs of damage, corrosion, or loosening.
- Ensure the heat-shrink insulation remains intact and fully sealed.
- If any damage is observed, disconnect power and replace the terminal.
6. Fejlfinding
If an electrical connection fails or performs inconsistently, consider the following:
- Løs forbindelse: Ensure the terminal is securely crimped to the wire and tightly fastened to the stud. Re-crimp or re-fasten if necessary.
- Poor Electrical Contact: Check for corrosion on the stud or terminal. Clean surfaces if needed.
- Beskadiget isolering: Inspect the heat-shrink for tears or punctures. If damaged, the terminal should be replaced to maintain environmental protection.
- Forkert trådtykkelse: Verify that the wire used is within the 16-14 AWG range for this terminal. Using an incorrect gauge can lead to poor crimps.
7. Specifikationer
| Feature | Detalje |
|---|---|
| Modelnummer | AMT-113 |
| Kompatibilitet med trådmåler | 16-14 AWG |
| Stud Size Compatibility | 8-10 |
| Connector Type | Spade Terminal |
| Isoleringsmateriale | Polyvinyl Chloride (Heat-Shrink) |
| Kontaktmateriale | Kobber |
| Voltage Bedømmelse | 600 volt |
| Temperatur vurdering | 257°F (125°C) |
| Overholdelse | UL-listet |
| Omtrentlige pakkemål | 7.6"L x 5.1"W x 12.7"H (for 3-pack) |
| Omtrentlig varevægt | 0.32 ounces (for 3-pakning) |
8. Garantioplysninger
Gardner Bender products are manufactured to high-quality standards. For specific warranty details regarding the AMT-113 Xtreme Environment Spade Terminals, please refer to the official Gardner Bender webwebstedet eller kontakt deres kundesupport direkte. Garantivilkår og -betingelser kan variere.
9. Support og kontakt
For further assistance, technical support, or additional product information, please visit the official Gardner Bender webwebsted:
Visit the Gardner Bender Store
You may also find contact information for customer service on their webwebsted.
