1. Introduktion
This manual provides detailed instructions for the proper installation, operation, and maintenance of your Lanzar VIBE211 Vibe 360 Watt 2 Channel Mosfet Amplifier. Please read this manual thoroughly before attempting to install or operate the amplifier for at sikre optimal ydeevne og sikkerhed.
2. Sikkerhedsoplysninger
Overhold altid følgende sikkerhedsforanstaltninger under installation og drift:
- Disconnect the vehicle's negative battery terminal before any wiring connections are made.
- Sørg for, at alle ledninger er korrekt ført og fastgjort for at forhindre skader eller kortslutninger.
- Brug passende ledningsføring til strøm- og jordforbindelser som angivet i installationsafsnittet.
- Monter ampOpbevar køleren sikkert på et sted, der giver tilstrækkelig ventilation og er beskyttet mod fugt og overdreven varme.
- Betjen ikke amplifier if it is damaged or malfunctioning. Refer to the troubleshooting section or seek professional assistance.
3. Produktet er slutview
The Lanzar VIBE211 is a 2-channel Mosfet amplifier designed for car audio systems. It features a bridgeable design, allowing for flexible configuration, and incorporates a regulated Mosfet power supply for stable performance. Key features include variable high/low pass crossover controls and a remote subwoofer bass control.
En vinklet view of the silver Lanzar VIBE211 Vibe 360 Watt 2 Channel Mosfet Ampløfter, showcasing its finned heatsink design, RCA inputs, and control panel. The amplifier features text indicating 'bridgeable 2 channel amplifier', 'vibe 211', 'Lanzar vibe', '360 watts', 'high/low pass crossover', and 'regulated mosfet power supply'. A small, separate remote bass level control unit is visible in the foreground.
4. Opsætning og installation
4.1 Montering af Amplivligere
Choose a secure mounting location that provides adequate air circulation around the amplifier's heatsink. Avoid mounting in direct sunlight or areas prone to moisture. Use the provided mounting hardware to secure the amplifier firmly to a solid surface.
4.2 Ledningsforbindelser
Ensure all connections are tight and properly insulated to prevent short circuits.
- Effekt (B+): Connect a heavy-gauge wire (e.g., 8 AWG or larger) directly from the positive terminal of the vehicle's battery to the amplifier's B+ terminal. Install an appropriate fuse (15A) within 18 inches of the battery.
- Jord (GND): Connect a heavy-gauge wire of the same size as the power wire from the amplifier's GND terminal to a clean, unpainted metal surface of the vehicle chassis. Ensure a good electrical connection.
- Fjernbetjening (REM): Connect a smaller gauge wire (e.g., 18 AWG) from the ampFjernbetjeningens REM-terminal til fjernbetjeningens tændingsudgang på din hovedenhed. Denne ledning tænder amptænd og sluk for højttaleren med dit stereoanlæg.
- RCA-indgange: Connect the RCA audio cables from your head unit's pre-amp udgange til amplifier's Gold RCA Inputs. The amplifier includes Line Outs for Left and Right Channels for daisy-chaining to other amplivførere.
- Højttaler udgange: Connect your speakers to the amplifier's speaker terminals. Observe correct polarity (+ to + and - to -). The amplifier is 2 Ohm stereo stable and bridgeable at 4 Ohms.
- Remote Subwoofer Bass Control: Connect the remote bass control unit to the designated port on the amplifier. Mount the control unit in an accessible location for easy adjustment.
5. Betjeningsvejledning
5.1 Indledende opstart
After all connections are made, reconnect the vehicle's negative battery terminal. Turn on your head unit. The amplifier features Soft Turn On/Off circuitry to prevent pops and clicks. Power Protection LED Indicators will illuminate to show operational status.
5.2 Adjusting Input Level Controls
De amplifier has Variable Input Level Controls. Start with the amplifier's input level set to minimum. Play a familiar piece of music through your head unit at about 75% of its maximum volume. Slowly increase the amplifier's input level until you hear slight distortion, then back it off slightly. This ensures the amplifier receives an optimal signal without clipping.
5.3 Delefiltreindstillinger
De amplifier features Variable High Low Pass Crossover Controls. These allow you to filter specific frequencies to your speakers or subwoofers.
- Højpasfilter (HPF): Used for full-range speakers to prevent low frequencies from reaching them, improving clarity.
- Lavpasfilter (LPF): Used for subwoofers to allow only low frequencies to pass, enhancing bass response.
Adjust these controls to match the frequency response characteristics of your speakers and subwoofers.
5.4 Bass Boost Circuit
The built-in Bass Boost Circuit allows for an increase in bass output at specific frequencies. Use this feature sparingly and adjust to your preference, avoiding excessive boosting that could lead to distortion or speaker damage.
5.5 Bridged Mode Operation
De amplifier can be bridged at 4 Ohms to combine the power of both channels into a single, higher-power output, typically for driving a subwoofer. Refer to the wiring diagram for specific instructions on bridging the amplivligere.
6. Vedligeholdelse
The Lanzar VIBE211 amplifier requires minimal maintenance. Periodically inspect the wiring connections for tightness and corrosion. Keep the amplifier's heatsink clean and free of dust or debris to ensure proper cooling. Use a soft, dry cloth for cleaning the exterior.
7. Fejlfinding
Hvis du oplever problemer med din ampLifier, se følgende tabel, før du søger professionel service:
| Problem | Mulig årsag | Løsning |
|---|---|---|
| Ingen strøm / ingen lyd | Blown fuse; Loose power/ground/remote wire; Faulty head unit. | Check and replace fuse; Verify all power, ground, and remote connections; Test head unit functionality. |
| Forvrænget lyd | Input level too high; Speaker impedance too low; Damaged speakers. | Adjust input level; Verify speaker impedance (2 Ohm stereo stable, 4 Ohm bridged); Inspect speakers for damage. |
| Amplifier Goes into Protection Mode | Overheating; Short circuit in speaker wiring; Low voltage. | Ensure adequate ventilation; Check speaker wires for shorts; Verify battery voltage og ladesystem. |
| No Bass from Subwoofer | LPF not enabled or set too high; Phase issue; Remote bass control set to minimum. | Adjust LPF setting; Check subwoofer phase; Increase remote bass control level. |
8. Specifikationer
Technical specifications for the Lanzar VIBE211 amplivligere:
- Power Output (RMS @ 4 Ohms): 2 x 90 watt
- Power Output (Max @ 4 Ohms): 2 x 180 watt
- Power Output (Max Bridged @ 4 Ohms): 1 x 360 watt
- Power Output (RMS @ 2 Ohms): 2 x 150 watt
- Amplivligere Type: 2 Channel Mosfet
- Frekvensrespons: 15 Hz - 35 kHz
- Signal-til-støj-forhold (S/N): 90 dB
- Sikringsvurdering: 15A
- Dimensioner (B x H x L): 10.25 tommer x 2 tommer x 8 tommer
- Indgangsniveaukontrol: Variabel
- Crossover kontrol: Variable High/Low Pass
- Stabilitet: 2 Ohm Stereo Stable, Bridgeable at 4 Ohms
- Beskyttelseskredsløb: Advanced Power Protection LED Indicators
- Yderligere funktioner: Remote Subwoofer Bass Control, Electronic Crossover Network, Bass Boost Circuit, Soft Turn On/Off
9. Garanti og support
9.1 Garantioplysninger
The Lanzar VIBE211 amplifier leveres med en 1-ÅR limited warranty from the date of purchase. This warranty covers defects in materials and workmanship under normal use. Please retain your proof of purchase for warranty claims. The warranty does not cover damage caused by improper installation, accident, misuse, abuse, negligence, or unauthorized modification.
9.2 Kundesupport
For technical assistance, troubleshooting beyond this manual, or warranty service, please contact Lanzar customer support. Refer to the official Lanzar webwebstedet eller produktemballagen for aktuelle kontaktoplysninger.
