AKO CAMRegis Basic Owner’s Manual

AKO CAMRegis Basic

Advarsler

• Enheden skal installeres på et sted, der er beskyttet mod vibrationer, vand og ætsende gasser, hvor den omgivende temperatur ikke overstiger den værdi, der er angivet i de tekniske data.
• For the unit to operate correctly, use only the probes supplied by AKO. For the reading to be correct, the probe should be used in a place without heat influences apart from the temperature you want to me-asure or control.
• Sonden og dens kabel må ALDRIG installeres i et rør sammen med strøm-, kontrol- eller fødekabler.
• In the event of lengthening the NTC probe, always used shield cable and earth the mesh. In these cases, the maximum deviation will be 0.25 ºC from -40 ºC to +20 ºC (Maximum 1000 m with a minimum section of 0.5 mm2 ).
• We recommend using AKO-15586 cable. Always disconnect the power supply to do the wiring.
• The power circuit should be equipped with a switch marked as dis-connecting device of the equipment of at least 2 A, 230 V, situated near the appliance.
• The power supply cable should be H05VV-F or H05V-K type. The gauge will depend on local regulations, but should in no case be less than 1 mm2 . The electrical installation should be carried out under pipe. Using the logger not observing the manufacturer’s instructions may alter the appliance safety requirements. Only probes supplied by AKO should be used for the appliance to operate correctly.

Installation

DIMENSION

 Tekniske specifikationer

• Power supply……………………………………………… 90-240 V~ 50/60Hz
• Alarm relay…………………………………………………………… 8 A cos j=1
• NTC range (AKO-14931)…………………………………. -50 ºC to 99.9 ºC
• Range 4-20 mA…………. Configurable from -100 to 900 (1000 levels)
• Resolution ………………………………………………………………………..0,1
• Accuracy class (-40 ºC to 40 ºC):………………….. ±1 ºC acc/ EN 12830
• Response time:……………………………………………………. < 20 seconds
• Maximum relative time error:…………………………………………< 0.1 %
• Marked according to UNE-EN 12830……………..S,A,1,-40 ºC + 40 ºC
• ………………………………………………………… Velegnet til opbevaring (S)
• …………………………………………………………..Klimatisk miljøtype (A)
• ………………………………………………………………………….. Nøjagtighedsklasse (1)
• Maximum input power……………………………………………………8.5 VA
• Working ambient temperature…………………………………0 ºC to 40 ºC
• Storage ambient temperature……………………………… -20 ºC to 60 ºC
• Degree of protection…………………………………………………………IP40
• Dobbelt isolering mellem strømforsyning, sekundærkreds og relæudgang.
• Installation category……………………………………… II acc/ EN 61010-1
• Pollution degree…………………………………………… II acc/ EN 61010-1
• Maintenance of date and time without power supply……Up to 2 days
• Internal buzzer………………………………………………….. 70dB at 30 cm
• SD cards accepted……………………………………SD/SDHC (FAT / FAT32)

 Ledningsføring

Operation

Nøglefunktion

• key: A short press displays the maximum value reached in the last 24h, and the time when all the active inputs were reached. In the programming menu it allows scrolling around the different levels, or during the setting of a parameter, changing its value.
• key: A short press displays the minimum value reached in the last 24h, and the time when all the active inputs were reached. In the programming menu it allows scrolling around the different levels, or during the setting of a parameter, changing its value.
• key: A short press downloads the data of the ongoing log onto the SD card (if it has been inserted)
• key: A short press downloads ALL the logged data onto the SD card (if it has been inserted). The save without changes, return to previous level or exit programming parameter appears on the programming menu.
• SET key: A short press downloads the data of the last log onto the SD card (if it has been inserted).
• Slår den akustiske alarm fra (i henhold til parameter P50).
• Under programmering bekræfter valget og gemmer den indtastede værdi.
•   keys : Pressing for over 10 seconds accesses the data log display menu.
• Trykke for at vælge logblokken, og tryk på SET for at få adgang til den.
• Trykke  for at vælge den log, der skal vises, vil værdien af ​​hver input blive vist efter 1 sekund, der angiver dato og klokkeslæt for loggen.
• N + O keys : Pressing for over 10 seconds accesses the alarms log display menu.
  Press N / Q to select the input to be displayed and press SET.
  Press N / Q to select the event to be displayed (no. 1 is the most recent event), after 1 second the value of each input will be displayed, indicating the date and time of the event.
• keys: Pressing them for over 10 seconds accesses the programming menu.

Struktur af de loggede data

• De loggede data gemmes i loggerens interne hukommelse organiseret i logblokke. Tidsrummet, der er lagret i hver blok, og den maksimale kapacitet af den interne hukommelse, afhænger af log-intervallet (L1-parameter), som vist i tabellen.
• Loggeren har et slot til SD-kort, som gør det muligt at overføre de lagrede data til visning på en computer eller til at blive gemt som backup. Disse data gemmes i regnearksformat (.csv), organiseret på følgende måde:

VIGTIG: Do not remove the SD card until the indicator turns off. The download may take several minutes depending on the data saved.

• Downloads ALL the logged data (P key)
  To files genereres, hvis navn er året, måneden og dagen for download, i to forskellige mapper ALL og ALARMS. Den første indeholder file med alle data logget af enheden indtil da, og den anden indeholder file med begivenhederne gemt indtil da (se afsnit 5.2):
•  Alarmlog
  This function saves an event whenever an alarm is activated or deactivated. To download the events log data, press the P key, all the data logged up to date are downloaded onto the SD card, including the events log, contained in the “ALARMS” folder.
•  Indledende opstart
  Dato og klokkeslæt vil blive anmodet om ved første opstart.

 Programmeringsmenu (parametre)
To access the parameter programming menu, press the N + Q keys at the same time. Refer to the list of available parameters in section 5 of this manual. After 20 seconds without touching any key, the unit returns to the previous level. If it is in level 3 the changes will not be saved.

Parameter og meddelelsestabel

Def. kolonne angiver fabriksstandardparametrene. Medmindre andet er angivet, er temperaturværdierne udtrykt i ºC (ækvivalent temperatur i ºF).